Question about 1995 Chevrolet Suburban

1 Answer

What kind of brakes are on the back - 1995 Chevrolet Suburban

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 138 Answers

Call auto parts supplier for info

Posted on Jun 25, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Brake pedal goes almost to the floor


Is the brake fluid low in master cylinder reservoir? Notice any fluid around the area. Have you checked your brake cylinders for brake fluid leaks?

Jun 26, 2014 | 1993 Mercury Tracer

1 Answer

After replacing leaky rear lines and while bleeding i couldn't seem to get any kind of a pedal i held it after pumping quite a few times i did end up with a steady stream without the pedal moving ,so...


sounds like one of the bleeder nipples wasn't tightened properly. There's a cool little bleeder kit that has a blocker ball in it so it doesn't allow any air back into the brake line when you go pump the brake pedal until you tighten the nipple.

Oct 04, 2013 | 1999 Mazda 626

1 Answer

Brake peddle jumping back when prested on funny kind of rumbling from the brake cylender


Peddle jumping is your anti lock brakes activating. Rumbling could be anti lock recycling or your brakes are grinding and need replacing

Mar 23, 2011 | Ford Explorer Sport Cars & Trucks

2 Answers

My brake light did not warn me that i needed brakes


someone probably topped off your brake fluid when your brakes were low. the only way i know is to have new front and back brakes then make sure the brake fluid level is right . the light only comes on if your brake fluid goes low so the system has too much fluid if it says full and your brakes are not new front and back

Dec 16, 2010 | 2005 Mercury Mountaineer

1 Answer

I need to have brake. What kind of brakes for front and back?


YOU NEED PADS FOR THE FRONT BRAKES AND BRAKE SHOES FOR THE BACK BRAKES.

Jun 28, 2010 | 2005 Chrysler Town & Country

1 Answer

Asking which kind of brake in back rear driver makes a lot a nois


You have brake rotors and pads on the front. Looking on the rear axle if it looks like the front it will be rear rotor and pads. And if you cannot see the rotor or pads on the rear axle then you will have what is called rear drums and brake shoes. Hope this will help you.

May 20, 2010 | Cars & Trucks

1 Answer

Asking which kind of brake in back rear driver makes a lot a nois


What exactly is your question? Read what you wrote and then write it again so we can understand what you are asking.

Apr 19, 2010 | 1994 Toyota Tercel

1 Answer

Brake warning light is on, emergency brake is ok. Is brake cylinder at back of engine on driver side? Do I just add brake fluid to the fill line? Is there a particular kind of brake fluid to use?


If the fluid is lower use dot3 brake fluid.There is a sensor in the master cylinder for the level.If the light goes off then have your brakes checked out if your pads are low the the calipers will be moved out when this happens the fluid level will drop if the calipers are push back in after brake pads are installed the fluid level will go back up i hopes this helps :)

Jan 31, 2010 | 1990 Toyota Pickup

1 Answer

Rear brake piston compression problem? How do I compress the rear piston into the caliper to allow new brake pads to be installed?


As far as I know, most front disc brake setups have pistons that are pressed back into the cylinders using a C-clamp or something similar.

However, not all rear disc systems are like this. There are some that require that the rear pistons be screwed back into the cylinder bores. These pinstons usually have some kind of indentations on the front where special tools fit and help move them back into the cylinder.

Your Hyundai may have this kind of setup.

Oct 15, 2009 | 2001 Hyundai Elantra

Not finding what you are looking for?
1995 Chevrolet Suburban Logo

Related Topics:

21 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6924 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...