Question about 1998 Land Rover Discovery

1 Answer

Zee4real. how do i fix my landrover disco. 2004 that cannot start if it is in parking but can start when a small pin on the gear lever(park-neutral switch) is pressed in and the car is placed in neutral. this car was in a rake but has been fixed and the fuel cut switch activated but cannot start unless in neutral and the key cannot be removed unless the batery head is removed.

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 138 Answers

Shifter Linkage to transmission has to be adjusted.

Posted on Jun 25, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

P0705 code on 2005 MB ML350


Possible causes Faulty Park/Neutral Position Switch Misadjusted Park/Neutral Position Switch Park/Neutral Position Switch harness is open or shorted Park/Neutral Position Switch circuit poor electrical connection What does this mean? When is the code detected? The transmission range switch detects the selector lever position and sends a signal to the TCM. Possible symptoms Engine Light ON (or Service Engine Soon Warning Light) P0705 MERCEDES-BENZ Description The park/neutral position (PNP) switch includes a transmission range switch. The transmission range switch detects the selector lever position when the shift lever is in the N or P shift position and sends a signal to the Transmission Control Module (TCM).

Jul 13, 2017 | Mercedes-Benz Cars & Trucks

1 Answer

Wont shift out of park


You need to pull off the gearstick trim and reach down on the left side if the housing.

You will see a black plastic lever arm. Using a long screwdriver or rod, you need to move the small plastic lever and pull the gear selector lever to reverse or neutral .

Nov 15, 2013 | 2004 Jaguar X-Type

2 Answers

Driving down the road my 2004 trailblazer when into neutral engine still running fine,now all I have is park but all other gears are neutral


Trans has to out & be taken apart
Internal failure
There are things a shop could check first,
but no reason to come out of gear

Aug 11, 2013 | 2004 Chevrolet TrailBlazer

1 Answer

What is a neutral safety switch?


The Neutral Safety switch monitors the position of your gear selector lever and either interrupts or allows the starting circuit in your car or truck to do its job. On newer vehicles it may also monitor the position of the brake pedal to make sure that the vehicle is in park or neutral AND that your foot is on the brake.

If your vehicle is equipped with a neutral safety switch, it should NOT start UNLESS the transmission is in Neutral or Park. On the other hand your vehicle SHOULD start when it is in Neutral or Park. If your car will start in Neutral but not in Park, you have a bad switch. Also, if your car or truck will only start by turning the key to the start position and wiggling the gear selector lever, your neutral safty switch is in need of replacement.

The nuetral safety switch is usually found near the gear shifter. If your car has the gear shift on the column, then the neutral safety switch is usully mounted on the steering column near the brake pedal. On floor mount or console mount vehicles you will find the nuetral safety switch mounted near or on the shifter mechanism.

Oct 24, 2012 | 1993 Cadillac DeVille

1 Answer

I HAVE A 1990 LS 400 WHEN TURNING KEY NO CRANKING AND HAVE GOOD BATTERY POWER. NO POWER TO STARTER WIRE ON STARTER SELINOD.WHAT CAN IT BE


It could be a bad ignition switch or bad starter wire from the starter switch, or the PNP is not adjusted correctly:

Here are instructions on how to remove and replace the PNP, but read over it to understand how to adjust:
Park/Neutral Safety Switch REMOVAL AND INSTALLATION ES300 1993-94 Models
  1. With the ignition switch in the LOCK position, disconnect the negative battery terminal. If equipped with an air bag system, wait at least 90 seconds or longer before performing any other work.
  2. Raise and safely support the vehicle.
  3. Disconnect the Park/Neutral switch connector.
  4. Remove the clip from the shift control cable.
  5. Remove the nut and control cable.
  6. Remove the bolts and pull out the Park/Neutral switch. To install:
  7. Install the Park/Neutral switch and loosely install the bolts.
  8. Adjust the switch and torque the bolts to 48 inch lbs. (5 Nm).
  9. Install the control shaft lever.
  10. Install the control shaft cable and torque the nut to 9 ft. lbs. (13 Nm). Fig. 1: The transaxle control shaft lever has a nut and washer to retain it - 1993-94 ES300 54617.gif
    Fig. 2: Removing the Park/Neutral switch - 1993-94 ES300 54618.gif

  11. Install the clip to the shift control cable.
  12. Lower the vehicle.
  13. Connect the negative battery cable.
  14. Make sure the vehicle will start only in the PARK or NEUTRAL position.
1995-97 Models Fig. 3: Aligning the neutral base line and groove - 1995-97 ES300 293716.gif
Fig. 4: Park/Neutral switch removal and installation - GS300, LS400, SC300 and SC400 300569.gif
Fig. 5: Park/Neutral switch adjustment - GS300, LS400, SC300 and SC400 300571.gif
  1. With the ignition switch OFF, disconnect the battery cables, negative terminal first. Allow 90 seconds to elapse before performing any other work.
  2. Apply the parking brake fully and block the rear wheels.
  3. Disconnect the electrical connector from the Park/Neutral position switch.
  4. Remove the locknut and disconnect the control cable from the manual shift lever.
  5. Remove the clip from the holding the control cable to the bracket.
  6. Remove the nut, washer and the manual shift lever from the manual valve shaft.
  7. Using a flat bladed tool, bend the lock washer back away from the nut.
  8. Remove the nut and lock washer from the Park/Neutral switch.
  9. Remove the two bolts and the Park/Neutral position switch. To install:
  10. Install the Park/Neutral position switch to the manual valve shaft. Leave the two bolts loose at this time.
  11. Install the lock washer and nut. Torque the nut to 61 inch lbs. (7 Nm).
  12. Using a flat bladed tool, bend the lock washer over the nut to secure the nut in place.
  13. Adjust the Park/Neutral as follows:
    1. Install the manual shift lever to the Park/Neutral switch and set the shift lever to the neutral ( N) position.
    2. Align the groove and the neutral basic line on the Park/Neutral switch.
    3. Hold the Park/Neutral switch in this position and tighten the two bolts to 48 inch lbs. (5 Nm).
  14. Install the manual shift lever with washer and nut.
  15. Install the control cable to the manual shift lever and install the nut. Torque the nut to 11 ft. lbs. (15 Nm).
  16. Install the control cable to the bracket by installing the clip.
  17. Connect the electrical connector to the Park/Neutral switch.
  18. Lower the vehicle and check the vehicles shifting positions.
  19. Connect the negative battery cable to the battery.
  20. Verify that the vehicle only starts in PARK or NEUTRAL.
GS300, LS400, SC300 and SC400
  1. With the ignition switch OFF, disconnect the battery cables, negative terminal first. Allow 90 seconds to elapse before performing any other work.
  2. Raise and safely support the vehicle.
  3. If necessary, remove the front exhaust pipe.
  4. Disconnect the neutral start switch connector.
  5. Remove the control shaft shift lever.
  6. Pry off the washer and remove the nut.
  7. Remove the bolt and pull out the neutral start switch. To install:
  8. Install the Park/Neutral switch and loosely install the bolt.
  9. Adjust the switch as follows:
    1. Loosen the neutral start switch bolt and place the shift lever in the N position.
    2. Align the groove and the neutral basic line.
    3. Hold in position and tighten the bolt to 9 ft. lbs. (13 Nm).
  10. Install the nut and washer.
  11. Install the control shaft shift lever.
  12. Connect the electrical connector.
  13. Install the front exhaust pipe. Torque the front nuts to 46 ft. lbs. (62 Nm). Torque the pipe support bracket to bolts to 32 ft. lbs. (43 Nm). Torque the No. 2 front exhaust pipe to the front exhaust pipe bolts to 32 ft. lbs. (43 Nm).
  14. Lower the vehicle.
  15. Connect the negative battery cable to the battery.
  16. Verify that the vehicle will only start in the N or P positions.
---
Maybe try to press the brake pedal and run the gear shift throughout the full range of gears while the car is on level ground, and retry the starter to see if there is a faulty PNP adjustment.

Try to start in Neutral not Park, and jiggle the gear shift back and forth to see if the PNP is not adjusted right.

Good luck on this repair.

Nov 09, 2010 | 1992 Lexus Ls 400

1 Answer

I have a 2004 GMC Envoy XT with 4wd. I started to


sounds like you have a broken shifter cable.Go under the rig and shift the transmision manually.Put on the parking brake and on the drivers side of the trany should be the lever to move.Look for the broken part while you are there it will also help to locate the shift lever on the trany.

Jul 31, 2010 | 2004 GMC Envoy

1 Answer

Hi, I own a 1997 Ford E 350 Econoline, I have the following transmission engagement problem: Truck will not start: Transmission will not engage any gear, neutral or park. The shift lever feels like is not...


The weld on the manual lever is known to break loose. First, with the wheels off the ground, with the lever in the park position, does the drive shaft lock in park? If yes or no sometimes, drop the trans pan. I bet the nut on the lever camd loose.

Mar 31, 2010 | 1994 Ford Econoline

2 Answers

How to replace neutral saftey switch on a 1980 cadillac deville?


Use like reference guide for GM Cadillac 1967-1989 Repair Guide Neutral Safety Switch - REMOVAL & INSTALLATION

All Except 1985-89 Eldorado and Seville
See Figure 1
The neutral safety switch prevents the engine from being started in any transmission position except Neutral or Park. The switch is located on the upper side of the steering column under the instrument panel on column shift cars, and inside the shift console on floor shift models.
  1. Remove the console for access on floor shift models.
  2. Disconnect the electrical connectors.
  3. Remove the neutral switch.

To install:
  1. Place 1967-70 column shift lever models in Drive, and 1971 and later models in neutral. Locate the lever tang against the transmission selector plate on column shift models.
  2. Align the slot in the contact support with the hole in the switch. Insert a 3 / 32 in. (2.38mm) diameter pin in place. The switch is now aligned in Drive position.

1973 and later neutral safety switches have a shear-pin installed to aid in proper switch alignment so that insertion of a pin is unnecessary. Moving the shift lever from Neutral shears the pin.
  1. Place the contact support drive slot over the drive tang. Install the switch mounting screws.
  2. Remove the aligning pin. Connect the electrical wiring, and replace the console.
  3. Set the parking brake and hold your foot on the service brake pedal. Check to see that the engine will start only in Park or Neutral.
7b3f2a9.jpg

Fig. 1: Installation of a common neutral safety switch



ADJUSTMENT
See Figure 2
1974 and later cars do not have a neutral safety switch. Instead, these cars have an interlock between the lock and the transmission selector, which is non-adjustable.
  1. Place the shift lever in Neutral.
  2. Move the switch until you can insert a gauge pin, 3 / 32 in. (2.38mm) diameter, into the hole in the switch and through to the alignment hole.
  3. Loosen the switch securing screws. Remove the console first, if necessary.
  4. Tighten the screws and remove the pin.
  5. Step on the brake pedal and check to see that the engine will only start in Neutral or Park.
05843d3.jpg


Fig. 2: Adjustment of a common neutral safety switch


1985-89 Eldorado and Seville
See Figure 3

All neutral safety/back-up light switches come with a small plastic alignment pin installed. Leave this pin in place.
  1. Place the shifter assembly in the Neutral position.
  2. Remove the shifter lever-to-switch nut and the lever.
  3. Disconnect the electrical connector from the neutral safety/back-up light switch.
  4. Remove the neutral safety/back-up light switch-to-transaxle bolts and the switch from the vehicle.

To install:
  1. Position the shifter shaft in the Neutral position.

If using an old switch or the plastic pin (new switch) is broken, install a3/32in. (2.38mm) diameter pin gauge (drill bit) into the neutral safety/back-up light switch; the switch is then locked into its Neutral position.
  1. Align the flats of the shifter shaft and the neutral safety/back-up light, then, align the switch-to-tang on the transaxle. Torque the switch-to-transaxle bolts to 22 ft. lbs. (30 Nm). Remove the pin gauge.
  2. To complete installation, reverse the removal procedures. Make sure that the engine starts only in the Park and Neutral positions.
c796664.jpg

Fig. 3: Neutral start and back-up lamp switch - 1985-89 Eldorado and Seville

Hope help with this (remember rated and comment this). Good luck.

Mar 21, 2010 | 1980 Cadillac Deville

1 Answer

Truck will not start.


sounds like the starter solenoid or starter relay or the "Park-Neutral Safety switch"

Try starting it in neutral, or carefully, hold the key in start while moving the shift lever from park to low gear slowly and - with your foot on the brake and parking brake on.

report back.

May 14, 2009 | 2005 Lincoln Navigator

1 Answer

1999 ram auto trans wont shift into park


you could need a throttle linkage adjustment. first check to see if your ram will start in "park" and "neutral" only. if it starts in any other gear=faulty neutral safety switch. replace. ok, now check linkage for proper adjustment...with engine off and in park...remove intake housing..disconnect cableend from attatchment stud on your throttle body..slide cable off the stud (carefully)..verify that the transmissionthrottle lever is fully forward (idle) position..and verify that the lever on the throttle body is at curb idle pos..insert small screwdriver under edge of the retaining clip and remove..center the cable end on attatchment stud to within 0.04", or 1mm. install retaining clip onto cable housing..check cable adjustment..be sure trans throttle lever and throttlr body lever move in sync with each other.

Jan 11, 2009 | 1999 Dodge Ram

Not finding what you are looking for?
1998 Land Rover Discovery Logo

208 people viewed this question

Ask a Question

Usually answered in minutes!

Top Land Rover Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

yadayada
yadayada

Level 3 Expert

75822 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8195 Answers

Are you a Land Rover Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...