Question about 1998 Jeep Wrangler

1 Answer

I have a 1998 Jeep Wrangler with a 3.5" lift kit. My problem is that about a year ago I noticed the front passenger side was beginning to dip. I have since replaced the shocks but that has not fixed the problem. I have gone to the local off-road shop and they were no help. This 'dip' doesn't affect how it drives, that I can tell, but it looks bad. Help!

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 314 Answers

Your springs could be going bad. Check these out.

Posted on Jun 25, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

89 jeep wrangler was carburated now has a Howell throttle body injection kit (kit was installed years ago) jeep has sat for 10 years now it will start but will not stay running without holding the key in...


check the ballast resistor near the coil. white thing with wires...

run a wire from the +battery to the +coil and test (no more than 30 seconds)
if it works, replace the ballast resistor.
ballast should have 12v on one side and 7v on the other side with the ignition on.

Sep 30, 2012 | 1989 Jeep Wrangler

1 Answer

I need to replace the cam sensor on my 97 jeep wrangler were do i find it in the motor..


For 1997 Jeep Wrangler 4WD 4.0L MFI 6cyl the Camshaft Position Sensor is located: Under hood, passenger side, front engine area, mounted on front of intake manifold

Hope helps (remember to rate this).

Oct 12, 2010 | 1997 Jeep Wrangler

2 Answers

I have a 88 jeep wrangler w/a 4in. lift when accelerating the jeep will pull to one side or the other pretty bad any ideas


Yes. Don't lift it in the first place. Your lift components are not correct for your application. Your getting the pulling, because the steering linkage/arms are wrong or wrongly installed. A good 4x4 shop, which I recall stopped existing 20 years ago or a frontend specialist ,if they will even touch it, could help. As your veh lifts on acceleration,the steering is out of travel,so to speak.

Feb 08, 2010 | 1988 Jeep Wrangler

1 Answer

I have a 1998 Jeep Wrangler and my windshield whipers, radio nor my turn signal are working.


I hate to state the obvious but you didnt say. have you checked your wiper relay and the fuses? Locted ubder the hood in a black box passenger side. Hope this helps.

Nov 11, 2009 | 1998 Jeep Wrangler

2 Answers

2005 jeep shimmy


Check front end again for any side play (small amounts at different locations can add up. Also check that steering box is not loose on frame.Check all bushings as well. If all else fails, if caster is adjustable have another degree or two put in. (positive)

Jun 26, 2009 | 2005 Jeep Wrangler

1 Answer

Blow rear differential


If all metal debris was not cleaned from inside housing it will make short work of bearings etc. If unit was not assembled correctly (requires skill, dial indicators and absolute attention to clearances), it will also quickly fail.If not properly filled with fluid same. If you went off-road and beat on it, that does not help either!!! 3" or any lift kit technically voids most warranties....in my opinion, a lift of 3" will not cause diff failure, especially that fast.

May 30, 2009 | 1998 Jeep Wrangler

1 Answer

Grinding sound near lower front end of jeep


Might want to chk. the axel, or maybe wheel bearing, or caliper hanging up. Sounds more like axel or bearing bad.

Mar 28, 2009 | 1990 Jeep Cherokee Limited

2 Answers

Loose steering on 2001 wrangler


you might think its tight but its not. it could be worn on the inside where the gears are and never know it. i would change the pitman arm soon

Jan 17, 2009 | 1998 GMC Suburban

Not finding what you are looking for?
1998 Jeep Wrangler Logo

Related Topics:

148 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8152 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...