Question about 2005 Ford Mustang

1 Answer

There is any way that the Spark Plug from a 1996

There is any way that the Spark Plug from a 1996 for mustang will work on a engine of a 2005 for mustand use a 1996 harnes

Posted by on


1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 221 Answers

For testing only it should work, but to get all the performance your 2005 engine offers, use Autolite HT0 sparkplugs
Be very careful removing the stock plug. Other are reporting that they break off easily and the heads might have to come off to get the broken pieces out. $$$$$$$$$

Be careful !!!

Good Luck

Posted on Jun 25, 2009


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

2 Answers

I have a 96 mustang with the 3.8 engine it will turn over but won't start it had a lot of gas in the oil when I bought the car eney ideal as to what can be wrong

I know you said you had spark to one plug but it sure sounds like a spark issue - especially since there was fuel in the oil. I'd re-check spark at the coil and all the plugs. Remember you only need fuel, air and spark for the engine to run. A tune up won't hurt either.

Feb 07, 2015 | 1996 Ford Mustang

1 Answer

I have a 1996 mustang with a 2005 f-150 engine in it. It has sat in a garage for 7 months without being started,what should i do before starting it?

hi,im elroy, u should change the oil and oil filter,drain old oil and refill with new oil, dont forget to change the oil filter before you refill with new oil.change all spark plugs

Feb 01, 2013 | 2005 Ford F-150

2 Answers

On the ford 1996 mustang crankshaft pully you have10,0,10 ,20 which 10 is the TDC engine 3.8

Niether, 0 Is top dead center. The numbers to the left are before top dead center, number to thr e right are after.

Feb 05, 2011 | 1996 Ford Mustang

1 Answer

How does the spark plug wires run on the ford 2.3 liter engine 8 spark plugs - Cached

This website gives you the digram

Dec 07, 2010 | 1993 Ford Mustang

2 Answers

I dont know in what order my spark plug wires hooked up.


Below are the firing orders for 5.0L, 4.6L, 3.8L, and 2.3L late model Mustangs. Remember to be very careful when checking your firing order because the ignition system on your car runs on very high voltage. Do not remove spark plug wires from the distributor or spark plugs while the engine is running.
Firing order sequences:
V8's 1-3-7-2-6-5-4-8
V6's 1-4-2-5-3-6
2.3L 1-3-4-2


Hope this help (remember comment and rated this) TY for using Fixya.

Apr 30, 2010 | 2005 Ford Mustang

1 Answer

Diagram for 1996 cougar car v8 where to put spark plugs wire

1 & 5 at front of engine. Says Mustang, but should be same.

May 22, 2009 | 1996 Lincoln Town Car

1 Answer

2005 ford mustang

chances are you blew the fuse... look in the engine compartment fuse panel near the battery....

Apr 09, 2009 | 2005 Ford Mustang

1 Answer

2005 V6 Mustang

check for fuel, spark and compression. these are the only things needed for a engine to run

Feb 08, 2009 | 2005 Ford Mustang

1 Answer

Replaced a 96 mustang 3.8 engine with a 95 mustang 3.8 engine.

check your cam positioning and crankshaft positioning sensors

Jan 01, 2009 | 1996 Ford Mustang

2 Answers

Cannot remove harmonic balancer

take one of the spark plugs out and turn the engine till that cillinder reaches full decomprecion and using a funnel put about 1/2 a quart of oil in there put the spark plug back in and turn the engine manually till that cillinder reaches compression when your done remove the spark plug and rotate the pistons a couple of times and the oil will come out this works i just did it on my 05
p.s. there will be a little smoke when you first start your engine from the last of the oil getting burnt out

Jul 26, 2008 | 2005 Ford Mustang

Not finding what you are looking for?
2005 Ford Mustang Logo

Related Topics:

70 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts


Level 3 Expert

79865 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers


Level 3 Expert

5687 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides