Question about Chevrolet Impala

1 Answer

Replaced battery in remote even though old battery still had 3 volts,tried to initialze per instructions and still won't unlock door.get no chime when programming, just run out of time.2001 chevy impala

Posted by on

  • doodlemant Jun 26, 2009

    Did nothing at all and when i try to reprogram it the phrase "PushFob" does not flash as the owners manual says it will.

×

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Chevrolet Master
  • 426 Answers

• Resynchronization may be necessary due to the security method used by the remote keyless entry system. Resynchronization may be necessary due to the security method used by the remote keyless entry system.
The transmitter does not send the same signal twice to the remote control door lock receiver (RCDLR). • The RCDLR will not respond to a signal that has been sent previously. This prevents anyone from recording and playing back the signal from the transmitter. • Resynchronization may be necessary under the following conditions: - The battery in the transmitter is very weak. - The battery in the transmitter was replaced. - The battery in the vehicle has been in a low or no charge condition for an extended period of time. • In order to resynchronize the transmitter with the RCDLR, perform the following steps: 1. Stand within 1.5 m (5 ft) from the vehicle. 2. Simultaneously press and hold the LOCK and UNLOCK buttons on the transmitter for 7 seconds

Posted on Jun 25, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Having trouble with keyless remote control on 1993 lexus es300. Replace battery on remote- still not openning doors. Help Please!


Try reporgraming it

1. Start with key out of ignition, drivers door is open all others closed and
drivers door is unlocked.

2. Insert key into the ignition (Do NOT Turn) and Pull key out.
3. Perform these steps within 40 seconds.
A. Using the power lock switch on the drivers door, perform 5 lock/unlock cycles
starting with lock. Use an even pace and try to go about one cycle per second.
(1Cycle = 1 lock and 1 unlock).
B. Close, then open drivers door.

4. Perform these steps within 40 seconds.
A. Using the power lock switch on the drivers door, perform 5 lock/unlock cycles
starting with lock. Use an even pace and try to go about one cycle per second.
(1Cycle = 1 lock and 1 unlock).
B. Insert the key in the ignition cylinder.
C. Turn the ignition to ON (Do NOT Start) then back to OFF.
D. Remove the key from the ignition.

5. Press any button on remote for a minimum of 1 second.
System should now lock and unlock doors once.

6. Close and open drivers door.

7. Press any button on remote for a minimum of 1 second. System should now lock and
unlock doors. Once to confirm programming, twice to indicate programming failed.

8. Repeat steps 5, 6 and 7 for additional remotes.

Jan 02, 2013 | Cars & Trucks

2 Answers

KEY FOB


Hi there:
From Owners Manual...
7_2_2012_3_58_16_pm.gif

Hope this helps; also keep in mind that your feedback is important and I`ll appreciate your time and consideration if you leave some testimonial comment about this answer.

Thank you for using FixYa, have a nice day.

Jul 02, 2012 | 2008 Dodge Ram 1500 2WD

2 Answers

08 dodge ram key FOB reprogramming


ATTENTION: You MUST HAVE one working remote to add one more to the system. If you do not have one working remote right now then these instructions will not work. You will have to have a Locksmith or dealership use a computer to program the first remote for you.

Click here to find a Locksmith in your area to program this remote.
1. Enter your vehicle and close all doors.

2. Fasten your seat belt ( fastening the seat belt will cancel any chiming that may
confuse you during this programming procedure.)

3. Place key into the ignition.

4. Turn the ignition to the ON position ( DO NOT START THE ENGINE )

5. Press and hold the UNLOCK button on a working remote.


6. Continue to hold the UNLOCK button, wait at least 4 seconds, but no longer than
10 seconds, then press and hold PANIC button.

7. When a single chime is heard, release both buttons. The chime indicates the system
is in program mode.

8. Press and release both the LOCK and UNLOCK buttons, simultaneoulsly on the remote
to be programmed.


9. A single chime will be heard. The chime indicates the the remote was recognized.


10. Within 4 seconds of hearing the chime, press and release any button on the remote
being programmed.

11. A single chime will be heard The chime indicates the remote has been programmed.

12. Repeat steps 8 to 11 for a total of 4 remotes.

13. Turn the ignition to the OFF position or wait 60 seconds to exit program mode.

Jul 02, 2012 | 2001 Mercedes-Benz C-Class

1 Answer

After changing battery my car won't shift out of park or start? HELP!!!


You've activated the vehicles anti theft system, sounds like. Hard to know without knows what type of vehicle you have

Apr 27, 2017 | 2006 Nissan Maxima SL

1 Answer

98 intrigue keyless entry


Here's what i found.

1. Close all doors.

2. Insert key into the ignition cylinder but do not turn it.

3. Press and hold the Unlock button on door lock switch on drivers door.
Hold until instructed to release in step 6.

4. Remove key from ignition and then insert key into ignition without turning ignition cylinder and remove key.

5. Insert key in ignition a third time and leave key in ignition. Do Not turn ignition.

6. Release door lock switch on drivers door panel.
A Chime will sound 3 times indicating that you are in programming mode.

7. Press both the Lock and Unlock buttons on the remote up to 30 seconds.
A chime will sound 2 times if remote has programmed successful.

8. Repeat step 7 if you are programming additional remotes.

9. Remove key from ignition to exit programming mode.

NOTE: If you are having trouble getting this procedure to work, we have found that some vehicles need step 3 to be done before step 2.

Did you make sure to pull the key out after the procedure? This closes the "programming mode".

Mar 14, 2012 | 1998 Oldsmobile Intrigue

1 Answer

Hi I m trying 2 program my remote on my 2001 Pontiac Aztec


Obtain all remote transmitters for this vehicle.

1. Close all doors.

2. Insert key into the ignition cylinder but do not turn it.

3. Press and hold the Unlock button on door lock switch on drivers door.
Hold until instructed to release.

4. Remove key from ignition and then insert key into ignition without turning ignition cylinder and remove key.

5. Insert key in ignition a third time and leave key in ignition. Do Not turn ignition.

6. Release door lock switch on drivers door panel.
A Chime will sound 3 times indicating that you are in programming mode.

7. Press both the Lock and Unlock buttons on the remote up to 30 seconds.
A chime will sound 2 times if remote has programmed successful.

8. Repeat step 6 if you are programming additional remotes.

9. Remove key from ignition to exit programming mode.

NOTE: If you are having trouble getting this procedure to work, we have found that some vehicles need step 3 to be done before step 2

Aug 02, 2011 | Pontiac Aztek Cars & Trucks

1 Answer

How do I program my keyless remote for my 2002 Rendezvous?


1. Close all doors.
2. Press and hold the Unlock button on door lock switch on drivers door.
Hold until instructed to release.
3. Insert and remove key from ignition 2 times. Do Not turn ignition.
4. Insert key in ignition a third time and leave key in ignition. Do Not turn ignition.

5. Release door lock switch on drivers door panel.
A Chime will sound 3 times indicating that you are in programming mode.
6. Press both the Lock and Unlock buttons on the remote up to 30 seconds.
A chime will sound 2 times if remote has programmed successful.
7. Repeat step 6 if you are programming additional remotes.
8. Remove key from ignition to exit programming mode.

Jul 23, 2009 | 2002 Buick Rendezvous

3 Answers

The Lexus car remote key control model ES300


try this:

1. Start with key out of ignition, drivers door is open all others closed and
drivers door is unlocked.

2. Insert key into the ignition (DO NOT Turn) and Pull key out.
3. Perform these steps within 40 seconds.
A. Using the power lock switch on the drivers door, perform 5 lock/unlock cycles
starting with lock. Use an even pace and try to go about one cycle per second.
(1Cycle = 1 lock and 1 unlock).
B. Close, then open drivers door.

4. Perform these steps within 40 seconds.
A. Using the power lock switch on the drivers door, perform 5 lock/unlock cycles
starting with lock. Use an even pace and try to go about one cycle per second.
(1Cycle = 1 lock and 1 unlock).
B. Insert the key in the ignition cylinder.
C. Turn the ignition to ON (Do NOT Start) then back to OFF.
D. Remove the key from the ignition.

5. Press any button on remote for a minimum of 1 second.
System should now lock and unlock doors once.

6. Close and open drivers door.

7. Press any button on remote for a minimum of 1 second. System should now lock and
unlock doors. Once to confirm programming, twice to indicate programming failed.

8. Repeat steps 5, 6 and 7 for additional remotes.

Mar 23, 2009 | 1997 Lexus ES 300

1 Answer

Setting up keyless remote entry with a new remote


1. Close all doors.
2. Press and hold the Unlock button on door lock switch on drivers door.
Hold until instructed to release.

3. Insert and remove key from ignition 2 times. Do Not turn ignition.
4. Insert key in ignition a third time and leave key in ignition. Do Not turn ignition.

5. Release door lock switch on drivers door panel.
A Chime will sound 3 times indicating that you are in programming mode.

6. Press both the Lock and Unlock buttons on the remote up to 30 seconds.
A chime will sound 2 times if remote has programmed successful.

7. Repeat step 6 if you are programming additional remotes.
8. Remove key from ignition to exit programming mode.

Dec 09, 2008 | 2002 Buick Rendezvous

1 Answer

Need programming instructions for RKE for 2000 Mazda 626


2000 Mazda 626
Note: Make SURE the battery is new.
Instructions for programming ONE keyless remote fob.
1. Open the driver’s door & leave open.
2. Insert the key in the ignition.
3. Turn the key to the on and off position 3 times.
4. Remove the key from the ignition.
5. After door open chime stops, press the door open button 3 times.
6. After chime, press any fob key twice.
7. After second chime, press any fob key twice again.
8. After third chime, press any fob key twice again.
9. Press the door open button once.
10. The car should give another acknowledgement chime.
11. Test key fob.
This DOES work. I just programmed mine successfully today, three hours ago.

Sep 03, 2008 | 2000 Mazda 626

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

707 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6918 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...