Question about 1999 Mercury Cougar

1 Answer

Key broke off in ignition lock cylinder. Can't remove cylinder.

My ignition key broke off in my key switch. Now the cylinder won't turn, and I can't get the broken portion of the key out of the cylinder. I have tried to remove the cylinder to no avail. The dealer says if I can remove the broken portion of the key, he can make me a new one. I have tried everything I can think of, and it won't budge. Can anyone help? Thanks

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Mercury Master
  • 2,984 Answers

Non-Functional Lock Cylinder

  1. Disconnect the negative battery cable.
  2. Remove the upper and lower steering column covers.
  3. Insert a 0.125 (3.17mm) drill bit in the hole at the top of the cylinder housing and drill out the retaining pin. NOTE: Be careful not to drill into the lock cylinder housing.
  4. Pull out the lock cylinder.
  5. Clean out all the metal shavings and check the tube for damage. If damaged, the housing must be replaced. To Install:
  6. Turn the new lock cylinder to accessory position and while pressing the retaining pin in, insert the lock cylinder into the housing.
  7. Turn the key to the OFF position the release the retaining pin.
  8. Try the lock cylinder operation in all positions.
  9. Reinstall the steering column covers.
  10. Reconnect the negative battery cable.

Posted on Jun 25, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Key won't come out of ignition on 1999 vw jetta


IGNITION KEY WILL NOT RELEASE

It can be faulty ignition lock cylinder. I suggest to wiggle the steering wheel a bit and see if the key gets released out. If that is not helping then first turn steering wheel to right and try removing the key, or next turn steering wheel to left and see if you can remove the key.

----------

Spray wd-40 in the ignition key hole and let it remain there for few minutes, after that once again try to remove the key and see if that helps.

---------

But if that is not helping then ignition lock cylinder has to be removed out and key has to be manually removed.

-----------

For more troubleshooting on these types of issues, I suggest you to refer the help links mentioned below. Its the accurate solutions mentioned in it. That will help you to narrow the problem: -----

Click the link below: ------


-----------

1999 Toyota Camry: Key Will Not Come Out Of Ignition?

http://whatisbyme.blogspot.in/2012/05/1999-toyota-camry-key-will-not-come-out.html

---------------

2001 Toyota Tacoma: Ignition Locked?

http://technoanswers.blogspot.in/2012/04/2001-toyota-tacoma-ignition-locked.html

------------

Ignition Switch Will Not Turn Off?

http://schematicsdiagram.blogspot.in/2012/04/ignition-switch-will-not-turn-off.html

-----------

Car will not turn the ignition to start?

http://technoanswers.blogspot.com/2012/01/car-will-not-turn-ignition-to-start.html

-----------

Ignition Key OFF but engine still running?

http://howtobyme.blogspot.in/2012/03/ignition-key-off-but-engine-still.html

--------------

Chevrolet Malibu: Key Stuck in ON position?

http://technoanswers.blogspot.in/2012/04/chevrolet-malibukey-stuck-in-on.html

2012 Dodge Ram: Ignition Key will not release?

http://whoisbyme.blogspot.in/2012/07/2012-dodge-ram-ignition-key-will-not.html

-----------

Ignition locked up on Mercury Villager?

http://technoanswers.blogspot.in/2012/01/ignition-locked-up-on-mercury-villager.html

-------------

Key won't turn in the ignition on Toyota land cruiser?

http://technoanswers.blogspot.in/2012/02/key-wont-turn-in-ignition-on-toyota.html

-------------------

How to remove ignition switch on VW Car models?

http://schematicsdiagram.blogspot.com/2011/12/how-to-remove-ignition-switch-on-vw-car.html

-------------

How to Replace Ignition Switch on Chevrolet Caprice Classic?

http://schematicsdiagram.blogspot.com/2011/12/how-to-replace-ignition-switch-on.html

-----------------

1995 Ford Taurus: Ignition switch not turning OFF?

http://repairhelpcenter.blogspot.in/2012/06/1995-ford-taurus-ignition-switch-not.html

-------------

Ignition Problem Troubleshooting

http://whoisbyme.blogspot.in/2012/07/ignition-problem-troubleshooting.html

------------------

These will help.

Thanks.

Feb 15, 2013 | 1999 Volkswagen Jetta

1 Answer

I have a 1998 Ford Windstar. Got in to drive, turned the key to start and 'snap' something seems to have broke within the ignition lock cylinder... all of the accessories are on... the key...


This happened to to me with my ranger. I went and bought in ignition and a junk yard and no problems after that. That way your not out of a lot of money.

Jun 02, 2011 | 1998 Ford Windstar

2 Answers

The car will turn over but won`t start but if I turn the key on and jump the starter it starts


Sounds like the ignition switch has gone kaput. The ignition switch come in two pieces, an electrical switch and a mechanical switch.

The switch electrical portion can be replaced separatly from the mechanical portion (tumbler that the key engages). It is not a real difficult repair but requires some mechanical knowlege of how the column is assembled.

This can be verified with electrical test equipment prior to buying a new electrical switch.

Apr 18, 2011 | 1994 Volkswagen Golf

2 Answers

Ignition


the actuator inside the sterring column that the lock cylinder turns is boken, this is a very complex job and is not for the home tech without a factory service manual.

Apr 21, 2010 | 1996 Ford Taurus

1 Answer

How do you program the keyless remote on a 2002 Intrigue?


1. Close the vehicle doors.
2. Turn OFF the ignition.
3. Remove the key from the ignition.
4. Press and hold the driver side door lock switch in the UNLOCK position.
5. Insert the ignition key into the ignition lock cylinder and remove the key. (Do not turn the ignition key in the lock cylinder.)
6. Insert the ignition key into the ignition lock cylinder and remove the key. (Do not turn the ignition key in the lock cylinder.)
7. Insert the ignition key into the ignition lock cylinder. (Do not turn the ignition key in the lock cylinder.) Leave the ignition key in the ignition lock cylinder.
8. Release the door lock switch. The vehicle will sound three beeps in order to verify the Program Mode has been activated.
9. Press the LOCK and UNLOCK buttons together on the keyless entry transmitter and hold until the vehicle beeps twice to verify that the transmitter has been successfully programmed (this take approximately 15 seconds).
10. Perform the previous step to program up to four transmitters (including your old ones).
11. Remove the ignition key in order to exit the Program Mode.


Good luck and thank you for using Fixya

Mar 09, 2010 | 2002 Oldsmobile Intrigue

1 Answer

Key ignition switch needs replaced lock cylinder how do i change key broke off inside damaged needs replaced wires broke off behind key switch


disconnect the battery and pull the air bag fuse out to diable the air bag. Remove the steering coulmb trim covers and expose the lock cylinder. If the lock cylinder can be turned and is functional then push in the bottom tab and turn the lock cylinder then pull the whole cylinder out. If the keys broke inside and the lock cylinder is not functional the bottom tab will need to be drilled out.
graphic.aspx?mod=reptiff&module_id=1&session_id=%7b812b1a44-e9f7-498d-9233-3843c35aa6d4%7d&image_guid=00010135&print_bw=0&

Feb 27, 2010 | 2000 Pontiac Sunfire

1 Answer

Car was stolen broke the ignition


REMOVAL

  1. On models equipped with airbag, disarm airbag as described under MAINTENANCE PROCEDURES/AIRBAG SYSTEM DISARMING.
  2. On all models, disconnect battery ground cable.
  3. Remove ignition switch as described under STARTING AND CHARGING SYSTEMS/COMPONENT REPLACEMENT AND REPAIR PROCEDURES/IGNITION SWITCH.
  4. Remove key light case from lock body, if equipped.
  5. On 1989 Accord models, place ignition lock cylinder in the ACC position.
  6. On except 1989 Accord, place ignition lock in the I position.
  7. On all models, position suitable punch into hole on lock cylinder housing and depress pin, then remove lock cylinder from housing.
INSTALLATION

  1. On 1989 Accord models, install ignition lock cylinder as follows:
    1. Place ignition lock cylinder in the LOCK position.
    2. Rotate key until it is almost at the ACC position, then insert lock cylinder until pin contacts housing.
    3. Rotate key to ACC position, then push pin in and insert lock cylinder into housing until pin clicks into place.
  1. On except 1989 Accord, install ignition lock cylinder as follows:
    1. Place ignition lock cylinder in the O position.
    2. Rotate key until it is almost at the I position, then insert lock cylinder until pin contacts housing.
    3. Rotate key to I position, then push pin in and insert lock cylinder into housing until pin clicks into place.
  1. Install ignition switch and connect battery ground cable.
SRS wire harness is routed near the ignition switch.

CAUTION:
  • All SRS electrical wiring harnesses are covered with yellow outer insulation.
  • Before disconnecting the SRS wire harness, install the short connector on the airbag.
  • Replace the entire affected SRS harness assembly if it has an open circuit or damaged wiring.
IGNITION SWITCH
  1. Remove the steering wheel, then remove the steering column covers.
  2. Disconnect the 7-P connector from the under-dash fuse box.
  3. Insert the key and turn it to "0."
  4. Remove the 2 screws and replace the base of the switch.

Feb 13, 2009 | 1992 Honda Accord

1 Answer

Ignition key switch


You have to use a pin or paper lip to insert in hole in igmition switch to release the lock cylinder. The key has to be in "on" position I think.

Removal
  1. Disconnect battery ground cable (14301) .
  1. Turn lock cylinder key to RUN position.
  1. Place a 3.17mm (1/8-inch) diameter wire pin or small drift punch in hole in upper steering column shroud (3530) under ignition switch . Press retaining pin while pulling out on ignition switch to remove it from lock cylinder housing (22074) .
Installation
  1. Install ignition switch by turning it to RUN position and pressing retaining pin. Insert ignition switch into lock cylinder housing . Ensure ignition switch is fully seated and aligned in interlocking washer before turning key to OFF position. This will permit cylinder retaining pin to extend into lock cylinder housing hole.
  1. Rotate ignition switch, using lock cylinder key, to ensure correct mechanical operation in all positions.
  1. Connect battery ground cable.
871404a.gif

Jan 13, 2009 | 1986 Ford Mustang

1 Answer

1990 Jeep Cherokee Ignition key replacement


Removal & Installation
Without Air Bag
See Figures 1, 2, 3 and 4
  1. Remove the turn signal switch.
  2. Insert the key in the lock cylinder and turn it to the ON position.
0900c152800a9f7f.jpgFig. 1: Using a pair of needle nose pliers, remove the key warning buzzer switch and contacts from the steering column
  1. Remove the key warning buzzer switch and contacts AS AN ASSEMBLY using needle-nosed pliers, or a paper clip with a 90° bend.
0900c152800a9f80.jpgFig. 2: Lock cylinder retaining screwSome steering columns may have a retaining screw holding the lock cylinder in the column. When servicing this type, simply remove the retaining screw and remove the lock cylinder.
0900c152800a9f81.jpgFig. 3: Using a small thin bladed tool, press in the ignition lock clinder retaining tab ... 0900c152800a9f82.jpgFig. 4: ... then pull out the lock cylinder from the steering column
  1. With the ignition switch still in the ON position, insert a thin screwdriver into the slot adjacent to the switch attaching screw boss (right-hand slot). Depress the spring latch located at the bottom of the slot to release the lock cylinder.
  2. Remove the lock cylinder.
To install:
  1. To install the lock cylinder, turn the key to the LOCK position. Insert the lock cylinder in to the housing far enough to contact the drive tang. Force it inward and move the ignition switch actuator rod up and down to align the components. When the components align, the cylinder will move inward and the spring-loaded retainer will snap into place locking the lock cylinder in the housing.
If the lock cylinder is retained by a screw, tighten the screw to 40 inch lbs. (5 Nm).
  1. Install the key warning buzzer switch.
  2. Follow the ignition switch installation procedures to adjust the ignition switch.
  3. Install the turn signal switch.
With Air Bag
Please refer to the ignition switch removal and installation procedure.50c573d.jpg73cc55f.jpgb9448d0.jpg278f367.jpg

Oct 22, 2008 | 1990 Jeep Cherokee Limited

Not finding what you are looking for?
1999 Mercury Cougar Logo

1,013 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mercury Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

fordexpert

Level 3 Expert

5501 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Are you a Mercury Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...