Question about 1997 Audi A4

2 Answers

No dipstick to put transmission fluid into

I had a similar problem...i was changing the oil...instead of draining the oil pan i did the transmission fluid and now i cant fill the tranny fluid because there is no dipstick to put the the transmission fluid into....WHAT THE FLIP DO I DO

Posted by on

Ad

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 6,784 Answers

HI, this transmission is a sealed type. you will need to purchase a special tool from the dealership to fill this unit properly.

Contact the nearest Audi dealer for this fill tool.

Posted on Jun 25, 2009

Ad
  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Governor:

    An expert whose answer got voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 81 Answers

There should be another plug on the tranny if not the one plug that u pulled out is also where u put the tranny fluid at with a special funnel.

Posted on Jun 25, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Change transmission oil


Hi Peter, If your Camry has an automatic transmission, for normal driving the auto fluid should be changed every 40,000km, there should be a drain plug on the transmission pan that takes a 10mm hex drive or 17mm socket to undo. You have two choices after driving the car onto ramps or jacking up and supporting on jack stands so you can safely get under the car. 1 - You can loosen and remove the transmission drain plug to let the auto fluid drain out into a container (careful not to lose the sealing washer) refit and tighten the drain plug and washer again. Remove the auto transmission fluid level dip stick, using a suitable funnel pour about 2.5 litres of suitable new auto trans fluid back into the transmission via the dipstick tube (I believe they take dexron 2 of 3 type fluid). Start the car and move it onto a level surface. With the engine running, handbrake on and brake pedal applied, shift the transmission from park through every gear selection slowly into 1st gear, then back to park. Leave engine running. Wipe the dip stick & insert it back into the dip stick tube fully, remove and check where the fluid level mark is on the end of the dipstick. If the fluid level indicates low or does not show at all, add 100ml of additional fluid and recheck the level till the fluid reaches the full mark on the dipstick. 2 - The second option is everything in the first option but includes replacement of the transmission filter and pan gasket. I would only do this if the car had travelled high km or the pan gasket was leaking. At the point where you've drained the old fluid into a container and refitted the drain plug and washer, remove all the transmission pan bolts and the transmission pan. If you have the time to let the fluid drain overnight prior to removing the pan it's a good idea because once the pan is removed, fluid will continue to drip from the transmission. You'll need to remove the old pan gasket, some may be stuck to the pan and or transmission, a razor blade type gasket scraper can be good for this but be careful not to scratch either surface when cleaning off the old gasket. Remove the bolts/nuts that hold the transmission filter onto the bottom of the transmission. Careful caus more fluid may drain out of the transmission or filter once removed. Fit the new filter and filter tube gasket & bolts/nuts, careful not to over tighten. Fit new pan gasket, pan and bolts. Continue with fluid filling procedure from option 1. I would suggest you only use option one and remember to double check the drain plug is tight. Also, remember to dispose of the old fluid correctly. Cheers

Nov 30, 2013 | 1993 Toyota Camry V6

1 Answer

Transmission fluid


Transmission fluid should be checked with the engine warmed up and running in Park. The dipstick is always near the back of the engine bay, and is VERY long when you pull it out. Transmission fluid should be red. It should not be brown.
Changing transmission fluid is much more difficult than changing engine oil. Engine oil can be changed by removing a plug and draining it out. Transmission oil can only be changed by removing brackets, removing the pan (think of a shallow oven pan bolted to the bottom of the transmission) and letting all the fluid drain out. A transmission fluid change should ALWAYS include a new filter and gasket as well. This is one best left to a shop with the proper tools.

Oct 26, 2013 | 1986 Ford Thunderbird

1 Answer

I have a 2005 Hyundai Santa Fe and I accidently put motor oil in the A/T oil spot. What should I do?


Don't run the engine at all. If it was started, the transmission pump will have pumped the motor oil all through the transmission-go have it professionally flushed. If the engine was not started, drop the transmission pan to drain the fluid, and get a new transmission filter. Put it back together and run the engine until the transmission fluid gets hot. Then change the fluid and filter again. After this, monitor the transmission fluid dipstick. If any traces of more motor oil in the pink fluid, do the drain and change filter a third time. (buy a case of transmission fluid-each drain and change will take about 6 quarts.)

Aug 18, 2013 | Cars & Trucks

3 Answers

Where do I put the transmission fluid


You put the fluid in where the dipstick is but check it often as to not over fill

Jun 11, 2011 | 1999 Ford Windstar

2 Answers

Just wanted to know how to change transmission oil.


Hello,

Before You change the transmission oil, You need to check if it is due for changing. To check the transmission oil. please follow the steps below:
  1. Open the hood and locate the transmission dipstick. It is in front of the engine on the left side, just behind the radiator cap.
  2. Pull the ring on top of the dipstick to remove it from its tube. Wipe it off with the paper towel and replace it. This will ensure an accurate reading.
  3. Remove the dipstick again an look at the markings at the tip. If the fluid on the stick is below the full line, add more transmission fluid.
  4. Repeat this procedure until the fluid reaches the correct level on the dipstick.

There are different types of engine therefore there are several ways to change their transmission fluid. Unless you got something in there via dipstick its really not necessary to ever change the ATF. It's a messy job because there's no drain plug to change the fluid, but You can do it yourself if you're so inclined. To change the fluid,

  1. You have to get under your vehicle and remove the pan from the bottom of the transmission.
  2. When you loosen the pan, fluid will start to dribble out in all directions so you need a fairly large catch pan. You should also know that removing the pan doesn't drain all of the old fluid out of the transmission. Approximately a third of the old fluid will still be in the torque converter. There's no drain plug on the converter so you're really only doing a partial fluid change. Even so, a partial fluid change is better than no fluid change at all.
  3. A typical fluid change will require anywhere from 3 to 6 quarts of ATF depending on the application, a new filter and a pan gasket (or RTV sealer) for the transmission pan. The pan must be thoroughly cleaned prior to reinstallation. This includes wiping all fluid residue from the inside of the pan and scraping all traces of the old gasket from the pan's sealing surface. Don't forget to clean the mounting flange on the transmission, too.
  4. When the new filter is installed, be sure it is mounted in the exact same position as the original and that any O-rings or other gaskets have been properly positioned prior to tightening the bolts. Then tighten the bolts to the manufacturer's recommended specs.
  5. When refilling the transmission with fresh fluid, be careful not to allow any dirt or debris to enter the dipstick tube. Using a long-neck funnel with a built-in screen is recommended.
  6. Do not overfill the transmission. Too much fluid can cause the fluid to foam, which in turn can lead to erratic shifting, oil starvation and transmission damage. Too much fluid may also force ATF to leak past the transmission seals.
  7. Add half a quart at a time until the dipstick shows full. The transmission really isn't full yet because the dipstick should be checked when the fluid is hot, and the engine is idling with the gear selector in Park. So start the engine, drive the vehicle around the block, then recheck the fluid level while the engine is idling and add fluid as needed until the dipstick reads full.
Hope this helped. Thank You for using FixYa!!!

Jan 27, 2011 | Lexus IS Cars & Trucks

2 Answers

How to Change transmission fluid on 2001 celica


Hi there, hope these few steps help:
  • Raise the car with a jack and support the vehicle with jack stands sufficiently rated to safely support the weight of the vehicle.
  • Place a large drip pan under the transmission.
  • Remove the transmission fluid drain bolt with a wrench. The drain bolt is located at the bottom of the transmission facing the pan. The pan is the large flat plate that covers the very bottom of the transmission.
  • Drain the transmission fluid into the drip pan.
  • Reinstall the transmission fluid drain bolt with the same wrench used to remove the bolt.
  • Lower the vehicle to the ground after removing the jack stands.
  • Open the hood and remove the transmission dipstick from the filler tube by pulling the dipstick. The end of the dipstick will be curved into a circle to allow a finger to slide into the circle to withdraw the dipstick.
  • Place a funnel into the dipstick tube and fill the transmission with new fluid by pouring the fluid into the dipstick tube.
  • Remove the funnel and check the fluid level with the dipstick until the fluid reaches the "Full" mark on the tip of the dipstick.
  • Start and allow the engine to run for a few minutes.
  • Move the transmission gear selector through all of the gears while depressing the brake pedal.
  • Turn the engine off and check the fluid level on the dipstick. Add transmission fluid if necessary.
Best of luck.

Jan 11, 2011 | 2001 Toyota Celica

2 Answers

Changing transmission fluid


Hello,

changing transmission fluid a messy job because there's no drain plug to change the fluid, but you can do it yourself if you're so inclined. To change the fluid, you have to get under your vehicle and remove the pan from the bottom of the transmission.
When you loosen the pan, fluid will start to dribble out in all directions so you need a fairly large catch pan. You should also know that removing the pan doesn't drain all of the old fluid out of the transmission. Approximately a third of the old fluid will still be in the torque converter. There's no drain plug on the converter so you're really only doing a partial fluid change. Even so, a partial fluid change is better than no fluid change at all.
A typical fluid change will require anywhere from 3 to 6 quarts of ATF depending on the application, a new filter and a pan gasket (or RTV sealer) for the transmission pan. The pan must be thoroughly cleaned prior to reinstallation. This includes wiping all fluid residue from the inside of the pan and scraping all traces of the old gasket from the pan's sealing surface. Don't forget to clean the mounting flange on the transmission, too.
When the new filter is installed, be sure it is mounted in the exact same position as the original and that any O-rings or other gaskets have been properly positioned prior to tightening the bolts. Then tighten the bolts to the manufacturer's recommended specs.
When refilling the transmission with fresh fluid, be careful not to allow any dirt or debris to enter the dipstick tube. Using a long-neck funnel with a built-in screen is recommended.
CAUTION: Do not overfill the transmission. Too much fluid can cause the fluid to foam, which in turn can lead to erratic shifting, oil starvation and transmission damage. Too much fluid may also force ATF to leak past the transmission seals.
Add half a quart at a time until the dipstick shows full. The transmission really isn't full yet because the dipstick should be checked when the fluid is hot, and the engine is idling with the gear selector in Park. So start the engine, drive the vehicle around the block, then recheck the fluid level while the engine is idling and add fluid as needed until the dipstick reads full.

Take care and good luck

Oct 26, 2010 | Toyota MR2 Cars & Trucks

2 Answers

How can i put transmission oil in a izuzu trooper


At transmission pan, there will be two drain plugs, the up most drain plug is where you fill it and check level, to check level, with engine running and in park, unscrew up most plug on transmission pan, if fluid come's out, level is good, if no fluid come's out need to add transmission fluid in that drain plug.

Jul 22, 2010 | 1999 Isuzu Trooper

1 Answer

Automatic transmission oil change


you have to remove the trans pan to drain and replace filter the fluid get refilled at the dipstick tube {drivers side rear of engine- black } with filter it should take 6 qts

Dec 10, 2009 | 1993 Ford Taurus

1 Answer

How to change the automatic transmission oil and filter. On 4 cylinder engine


Check fluid level every 12 months or 7500 miles, whichever comes first. Transmission fluid and filter should be changed every 100,000 miles. On THM 250C transmissions, intermediate (front) band requires adjustment every 60,000 miles, or as required.
1. With vehicle on level surface, apply parking brake and let engine run at curb idle. Move selector lever through all ranges, ending in "PARK". Remove dipstick and wipe clean, reinstall, then remove again and check fluid level mark on dipstick. Fluid level should check between "ADD 1 PT." and "FULL HOT" marks on dipstick.
RECOMMENDED FLUID Use only Dexron II or equivalent automatic transmission fluid.
CAUTION: If vehicle has been operated for an extended period of time at high speed, or in city traffic in hot weather, or if vehicle has been pulling a trailer, an accurate fluid level cannot be determined until fluid has cooled down (approximately 30 minutes after vehicle has been parked).
So let's get started... 1. With vehicle raised and drain pan placed under transmission, remove front and side transmission oil pan bolts. Loosen rear pan bolts approximately 4 turns each.
2. Carefully pry pan loose with screwdriver, allowing fluid to drain. Remove remaining bolts and oil pan with gasket. Remove screen/filter-to-valve body bolts and remove screen/filter with gasket.
3. Thoroughly clean pan and screen with solvent and dry with compressed air. Paper type filters should be replaced. Install new gasket or "O" rings, lubricated with clean oil, into screen/filter assembly.
4. Install screen/filter assembly to transmission. Use new pan gasket and install pan. Add proper amount of fluid to transmission through filler tube.
5. Start engine with shift selector lever in "PARK" position and with parking brake set. Check fluid level and add as required. CAUTION: DO NOT overfill.

Best of luck :)

Oct 20, 2009 | 1986 Pontiac Fiero

Not finding what you are looking for?
1997 Audi A4 Logo

933 people viewed this question

Ask a Question

Usually answered in minutes!

Top Audi Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

yadayada
yadayada

Level 3 Expert

76846 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

14384 Answers

Are you an Audi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...