Question about 1999 Isuzu Rodeo

1 Answer

WHERE DOES THE EGR Flow GO ON a 99 honda crv - 1999 Isuzu Rodeo

Posted by on


1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that gotĀ 5 achievements.


    An expert whose answer gotĀ voted for 20 times.


    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 145 Answers

Where does the flow go? eventually the exhaust. It has ports throught the intake manifold ,cylinder heads,egr valve ,bypass pipe,

Posted on Aug 09, 2009


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

2 Answers

99 maxima ran till it was parked now it turns over will not start gave code p0400 any ideas

The fault is somewhere around the EGR valve - probably the EGR valve or the throttle position sensor.

Before replacing any sensors try removing and cleaning the EGR.

Here's a Youtube link that may be of help to you:

1999 maxima egr Google Search

This link explains about the EGR:
P0400 Exhaust Gas Recirculation Flow Malfunction

CEL code P0400 EGR Flow Malfunction

Mar 27, 2016 | Cars & Trucks

1 Answer

99 Honda Passport EGR valve what's the difference between $49.00 valve and $300 valve both have the same warranty?

If they are both new EGR valves, the difference is $251. That's the only difference :) (An EGR valve that works is an EGR valve that works... no premiums or upgrades or high definition or anything... just an EGR valve.)

May 15, 2015 | Honda Cars & Trucks

1 Answer

How to chech climate control switch on 99 crv

as for my japan model 99 crv, there is no switch for climate control. So pls chech again yr model. yr sincerely naing lynn.

Jul 09, 2014 | 1999 Honda CR-V

1 Answer

Oil lea from the Valve cover plug...? Honda CRV 1998. any advice

Have a compression test done to check for worn rings. Check EGR valve/ solenoid and check the check vale from the cover to the manifold for correct operation

Sep 23, 2013 | 1997 Honda CR-V

2 Answers

99 acura code p1491

Code P1491 in Honda/Acura vehicles means insufficient EGR valve lift. Note - this is not the same as 0401 for EGR low flow when you have to clean EGR passage in the intake manifold. If code 1491 is not accompanied with 0401 - that could be faulty EGR valve itself. Try to reset the code, and if it will return soon - replace EGR valve. If, however you see both codes together - cleane the manifold passage before you replacing the valve.

Sep 20, 2012 | Acura RL Cars & Trucks

1 Answer

Where is the obd port in a 1997 Honda crv

Where can i find the OBD port of my 99 honda hrv?

Aug 23, 2012 | 1997 Honda CR-V

1 Answer

Honda crv start problems

First check the immobiliser is disarming before you go further. The vehicle handbook will provide details.

Jan 06, 2018 | Honda CR-V Cars & Trucks

1 Answer

My 99 crv stalls on cold starts,have to hold the gas pedal down until engine warms up

Here are 2 very common causes for your issue.
1. Dirty air filter.
2. Faulty, or dirty MAF, ( mass air flow ), sensor.

Both of these things can restrict air flow to the engine. Your ECM, ( electronic control module, also referred to as the computer ), regulates the fuel/air mix ratio for the engine, which should be 1 part fuel to 14.7 parts air. When the air is resricted it often causes the driver to have to compensate the lower air level with fuel, which may be why you have to hold the gas pedal down to prevent stalling.

I hope this helps you.

Mar 09, 2011 | Honda CR-V Cars & Trucks

1 Answer

I need a diagram for a honda crv 99 timming belt

My email is,I will send it to you if you email me,I can do it on here.

Dec 20, 2009 | 1999 Honda CR-V

2 Answers


The knock sensor is located on the side of the engine block. And the oxygen sensors are located in the exhaust system. There will be one oxygen sensor (upstream) screwed into either the exhaust manifold or the exhaust pipe before the catalytic converter. The other oxygen sensor (down stream) will be screwed into the exhaust pipe just after the catalytic converter.

May 12, 2009 | 1999 Isuzu Rodeo

Not finding what you are looking for?
1999 Isuzu Rodeo Logo

Related Topics:

244 people viewed this question

Ask a Question

Usually answered in minutes!

Top Isuzu Experts


Level 3 Expert

81285 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

14423 Answers

Are you an Isuzu Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides