Question about 2008 Dodge Charger

1 Answer

How do I remove my headlights on my 2008 dodge charger

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 721 Answers

The bulb is held in by a round screw in plastic clasp. Simply turn it counter clockwise a quarter turn & it out. Wiggle the bulb loose & unplug the wire. The headlight complete assembly is a different story & one I can't type out.

Posted on Jun 25, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to remove a oil pan from a 2008 dodge charger v6 2.7l


jack it up,drain all the oil.take all the bolts off,scrape all the gasket off without damaging the metal,put new gasket and pan on put all bolts back,

Jun 16, 2015 | 2008 Dodge Charger

1 Answer

Have a 2008 dodge charger the emergency release lever was accidentally pulled can tou tell me how to reset it


  1. Reset emergency trunk release 2007 dodge charger - Fixya

    www.fixya.com/.../t14008171-reset_emergency_trunk_release_2007_do... Aug 15, 2012 - reset emergency trunk release 2007 dodge charger - Dodge 2008Charger question.

Feb 28, 2015 | 2008 Dodge Charger

1 Answer

Dodge charger 2008 will not go from drive to park or Revere


the button on side of gear shift may be bad. remove gearshift and check button.

Jul 20, 2010 | 2008 Dodge Charger

2 Answers

Removing and replacing tension struts on 08 Dodge Charger


Here is a good write up on how to remove and replace your Tension struts. These appear to be easy to DIY, and i am going to follow this right up on my 07 Charger since the suspension for the 300/Magnum/Chargers are the same.. Dodge/Chrysler did not improve the setup as the years progressed.

http://www.300cforumz.com/showthread.php?t=78269

May 04, 2010 | 2008 Dodge Charger

1 Answer

How do I remove the headlight fixture from my 2008 Dodge Ram?


the headlight it self is a capusule it twists out then just unplug the capsule

Dec 17, 2009 | 2001 Dodge Ram 2500 Truck

1 Answer

Headlight pointing down, loose in housing


The adjustment screws/nuts should be located either on the top of the headlamp assembly, behind the headlamp assembly, or near the frame rail by the radiator support.

You will have vertical adjustment screws for each independent beam (separate highs and separate lows, but will be same screw if highs and lows are the same bulb). You may also have additional horizontal adjustment screws as well

Park your car on a level ground 30 feet from a wall and measure the height from the ground to the bulb and mark on a wall (do this for highs beams and low beams if the bulbs are separate, if highs and lows are the same bulb, only do it for the lows)

For Low Beams: If the headlights read VOR, then aim the brightest part or cutoff part just below the mark on the wall. If it says VOL or nothing, aim them 2 inches below the mark on the wall.

For High Beams (if separate from low beams): Aim the headlight directly at the line you marked on the wall.

Nov 19, 2009 | 2008 Dodge Charger

1 Answer

Install headlights on dodge charger


Pop the hood and find the back of the bulb you need to change and you should see a cover. Turn this cover a 1/4 turn counter clockwise and it will unlock the bulb and it can then be pulled out.

Sep 17, 2009 | 2008 Dodge Charger

1 Answer

Replace Bulbs in Headlight. 2008 Dodge Avenger


there is 2 bolts on top 1 top outer and 1 top front behind grill, u need to remove the top center black cover and 1 bottom side outer need to remove the inner finder liner to get to the 3rd bolt.
hope that helps, it is stupid

Mar 09, 2009 | 2008 Dodge Avenger

1 Answer

New 208 dodge charger with factory wig wag lights sometimes work and sometimes don't


To activate factory wigwags in a 2007/2008 Police Dodge Charger, connect pin 1 of the 24way upfitter connector found at the console (near the radio) to battery voltage -- the 47k series resistor is only required for MY2006.

That connection causes the VSIM module (located under the AM/FM radio) to send a CAN message to the FrontControlModule, where the front control module drives the headlights in the wigwag mode.

Pin 2 of the upfitter connector does the rear wigwags.

Some of the pinout of the 2008 upfitter connector from the VSIM to the console is different than 2006/2007 -- a Chrysler harness booboo for 2008.

Note that the VSIM (also known as PTIM) module is only on factory police Chargers -- civilian cars do not have this module.

Jul 18, 2008 | Dodge Charger Cars & Trucks

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

387 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8215 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...