Question about 1994 Nissan Pickup

1 Answer

Replace Rear brake light-Need Diagram of how to remove light assembly

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Contributor
  • 24 Answers

For the rear assemblies, there are two bolts per side. Look INSIDE the bed in the corners (behind each light location. The bolts are 10mm with a phillips pattern in the center. You can use a wrench, socket, or screw driver.

Posted on Jun 27, 2009

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
Pyrhyc
  • 2028 Answers

SOURCE: Replacing rear disk rotors on 2003 Mercedes E320

Generally when you remove the caliper assembly the rotor slides over the hub assembly. Since I have not done a brake job on this particular model, it may possibly be held in place by the hub nut. Remove the caliper assembly first in order to be sure. I could only find two diagrams for the brake assembly for the E320, neither one had the size of the nut or allan bolt. The easiest way to get the size is to measure from one flat area directly across to the other flat area this will give you the size for the socket and allan wrench needed. If in the US, keep in mind that this is in a metric measurement, so it will calculate to millimeters, which makes it much easier to measure than the American standard. Also, if you do have to remove the hub nuts, they will not have to be replaced unless you scar the threads or round the corners.

Posted on Jul 09, 2008

  • 1 Answer

SOURCE: Replacing the rear rotors on a 2003 E320

So this is what it takes to replace rear brake rotors on a 2003 Mercedes E320;
1) open the bonnet (hood) of the car and loosen/remove the cap off of the brake fluid resevior.
2) remove outer spring clamp from brake assembly (it clips in to the iner edge of the holes of the caliper).
3)using a 7 MM allen wrench, remove the brake caliper.
4) using 18 MM box wrench, remove the caliper housing assembly off of the wheel hub.
5) using a star wrench, unscrew the rotor locking screw from the rotor
6) squirt some liquid wrench on the rotor hub and knock the rotor with a hammer to work the liquid wrench in.
7) using the same hammer, knock the rotor off the hub.
8) using a metal file, lightly file old residue off of the hub and place the new rotor on the hub.
9) set the hub by screwing in the lug nuts and then screw in the hub locking screw using the star wrench, then remove the lug nuts.
10) reinstall the caliper housing assembly onto the wheel hub using the 18 MM box wrench.
11) push back the brake claiper piston to its home position and install the inner brake pad (the one with the snap clips)
12) insert the outer brake pad in the claper housing assembly.
13) slide on the caliper housing with the inner brake pad in place (over the outer brake pad) and screw in the caliper screw rods using the 7 MM allen wrench
14) on the right wheel brakes, DO NOT FORGET to slide in the brake sensor (the one with the black connector) and connect it to the connector on the caliper housing.
15) be sure to reinsert the spring clamp onto the outer brake assembly to set the assembly squarely onto the wheel (there should be no wiggle in the brake assembly after the spring clamps are installed).
16) finally mount the wheels.
17) you can bleed the brakes at this point to release any trapped air (which is unlikely) but be sure to pump the brakes after starting the car BUT BEFORE MOVING IT to re-preassurize the brake system before driving the car.
17) ONE WEEK LATER - recheck brake assembly to ensure all is okay and brake fluid.

This proposed solution is for a 2003 Mercedes Benz E320 and NOT a 2005 model as stated by the limited option selection provided by FIXYA.com when initially describing the problem.

Posted on Jul 10, 2008

  • 110 Answers

SOURCE: Rear brake diagram

Look at other side rear brake, if you can't transpose it in your mind, then stick a big mirror in front of the other side and take a photo of the brake image in the mirror ... hmmm,  you may end up thinking like this after a while.  I don;t know that that is a good thing;~).
good luck, ..ajm


please rate all solutions

Posted on Nov 06, 2008

  • 496 Answers

SOURCE: removing rear light assembly on honda odyssey 2006

Yes, there is a "spear point" plastic clip that is still engaged into a socket type holder in the front outboard portion of the tail lamp assembly. Pry gently with a tape wrapped screwdriver at the front outboard corner of the assembly and the clip will release. You will then be able to see how the clip works and will be able to align and engage it first when replacing the tail lamp assembly.

-T

Posted on Jan 24, 2009

MNfisherman
  • 11896 Answers

SOURCE: REAR BRAKE SHOE ASSEMBLY DIAGRAM

You can go to autozone.com and register for full free online repair manual that has the diagrams you need and everything else you could want.

Posted on Nov 18, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do i replace left rear brake light bulb


1) Open trunk
2) Remove small round plastic access panel with a flat tip screw driver by prying open
3) Remove flat tip screw holding tail light assembly
4) Remove tail light assembly by pulling outward, careful not to break plastic guide/nub
5) Disconnect wiring connectors
6) Remove plastic housing access plate on back of tail light assembly by twisting/turning tabs until they click and then lift access plate from tail light assembly
7) When viewing the the bulbs, the turn signal bulb is the bottom left bulb
8) Install in reverse order, ensuring tail light seal seats properly during installation

Oct 13, 2014 | 1999 Audi A4

1 Answer

How do I install new brake parts? I need brake assembly diagram.


Go to Youtube.Com type in year model and what you're looking to replace, I'm sure you'let find a video showing you exactly what needs replacing

Jul 24, 2014 | 2001 Ford Crown Victoria

1 Answer

Rear brake light top not working


You must replace the whole light assembly in this year, the part is very expensive and a dealer only item if still avail (which I doubt). You need to drop the headliner down in the rear to access the light fixture assembly by removing the trim at rate of cargo area.

Jun 17, 2012 | 1996 Ford Explorer

1 Answer

Replace a brake light, how do you remove the lens?


Hi there,

Well you can please follow the below link -
1. Open the rear hatch of the Murano.
2. Remove the screws holding the rear trim covers in place.
3. Pull off the rear trim covers to expose the rear taillight housing assembly.
4. Remove the power connector running to the brake light ballast.
5. Turn the brake light counterclockwise with your hand, and remove the light from the housing assembly.
6. Install the new brake light. Installation is in reverse of removal. Post comments for more help or information......

Good Luck!!

Mar 28, 2010 | 2003 Nissan Murano

1 Answer

Need to replace right brake light. How do I remove and replace trunk lining to get access withou doing damage to the liner? What is the correct lamp?


Remove the luggage compartment rear trim panel. Detach luggage compartment side trim panel. Detach the rear lamp assembly bulb holder. Remove the rear lamp assembly. To install, reverse the removal procedure.

Aug 03, 2009 | 2003 Jaguar S-Type

1 Answer

Remove and replace rear brake shoes on 2004 honda accord


Brake Shoes Removal & Installation To Remove:
  1. Raise and safely support rear of vehicle.
  2. Remove rear wheel assemblies.
  3. Release parking brake.
  4. Remove brake drum.
Rear brake shoe assembly


6c57c70.gif
  1. Using an appropriate brake spring tool, unhook upper return spring from rearward brake shoe.
  2. Push retainer springs IN and turn to remove tension pins.
  3. Lower brake shoe assembly and remove lower return spring.
  4. Remove brake shoe assembly from back plate.
  5. Disconnect parking brake cable from lever and remove brake shoe.
  6. Remove parking brake lever from brake shoe.

To Install:

d36458c.gif
  1. Install parking brake lever to rearward brake shoe.
  2. Secure lever to brake show with a NEW U-clip.
  3. Pinch U-clip closed.
  4. Connect parking brake cable to rearward brake shoe.
  5. Install self-adjuster lever spring on front brake shoe.
  6. Assemble clevises, adjuster bolt and upper and lower return springs.
  7. Apply a light coat of grease (Molykote 44MA or equivalent) to sliding surfaces.
  8. Install brake shoe assembly onto back plate.
  9. Install tension springs.
  10. Using an appropriate brake spring tool, unhook upper return spring to rearward brake shoe.
  11. Install brake drum.
  12. Install rear wheel assembly.
  13. Lower vehicle.
  14. Adjust self-adjusting brakes by pressing brake pedal several times.

Jul 13, 2009 | 2004 Honda Accord

1 Answer

How do i replace the brake light on my 1997 ford taurus?


To Remove:
  1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
  2. Remove the luggage compartment quarter trim panels.
  3. Disconnect the rear lamp assembly electrical connector.
  4. Remove the lamp assembly mounting nuts.
  5. Pull the lamp assembly away from the body.
  6. Disconnect the rear lamp assembly bulb connectors.
  7. Remove the rear lamp assembly.

Mar 29, 2009 | 1997 Ford Taurus

2 Answers

Removing rear light assembly on honda odyssey 2006


Yes, there is a "spear point" plastic clip that is still engaged into a socket type holder in the front outboard portion of the tail lamp assembly. Pry gently with a tape wrapped screwdriver at the front outboard corner of the assembly and the clip will release. You will then be able to see how the clip works and will be able to align and engage it first when replacing the tail lamp assembly.

-T

Jan 24, 2009 | 2007 Honda Odyssey

2 Answers

PT Cruiser Brake Light


The bulb in the rear light has burned out and to replace it follow these instructions: 1) go to your owner's manual to find out the part number. You can find and purchase the replacement bulb at Target, any auto parts store and even at Walmart for under $4.00; 2) pop open the trunk door; 3) get a phillips screw driver and unscrew the 2 screws holding the rear brake light fixture to your car body; 4) as soon as you turn over the fixture you'll see where to pull out the burned out bulb and replace it with the new one(s). Good luck!

Jul 14, 2008 | 2006 Chrysler PT Cruiser

Not finding what you are looking for?
1994 Nissan Pickup Logo

138 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

77499 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

726 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22306 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...