Question about 2006 Pontiac Montana SV6

1 Answer

How do i change the rear tail lamp bulb in my 2006 pontiac montana sv6

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 1,800 Answers

Bulbs used in most other lighting fixtures fit into sockets and are held in place by spring tension or mechanical force.
how do i change the rear tail lamp bulb in my 2006 - f19-42.gif Common type of automotive bulbs. Bulbs are coded with numbers for replacement purposes. Bulbs with different code numbers might appear physically similar but have different wattage ratings.
There are two basic construction designs for exterior lights: those in which the lens is removed and then the bulb removed from the front, and those in which the light assembly must first be removed, then the socket from the back of the assembly, and finally the bulb from the socket.

  • Removing the lens from the latter type assembly could cause serious damage to the reflector due to dust and other contaminants.
  • Wiping the reflector surface to clean it can also seriously reduce the light's brightness. Therefore, do not remove the lens from light assemblies in which the socket and bulb are removed from the back of the assembly.
  • The bulbs are held in their sockets in a number of ways.
  • Some bulbs are simply pushed into and pulled out of their sockets, and some are screwed in and out.
  • To release a bayonet-style bulb from its socket, the bulb is pressed in and turned counterclockwise.
  • The blade-mount style is removed by pulling the bulb off the mounting tab, then turning the bulb and removing it from the retaining pin.
  • To replace a bulb, remove the bulb accordingly from its socket, and insert a new bulb.

Posted on Jun 25, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2005 PONTIAC MONTANA FUSE BOX DIAGRAM


On this website you find fuse box diagram for Pontiac Montana SV6 2005 - 2006

Pontiac Montana SV6 2005 2006 fuse box diagram Auto Genius

Mar 02, 2013 | 2006 Pontiac Montana SV6

1 Answer

Where 2005 Pontiac Montana SV6 heater fuse in the box


On this website (link below) you find fuse box diagram and description for Pontiac Montana Sv6 (2005 - 2006)

Pontiac Montana SV6 2005 2006 fuse box diagram Auto Genius

Feb 01, 2013 | Pontiac Montana SV6 Cars & Trucks

1 Answer

How do you get access to change the front right turn signal bulb on a 2005 pontiac montana SV6?


Open the hood. If you cannot gain access, the grill of the vehical will have to be removed. This will give you access to the bulb.

Apr 17, 2011 | 2005 Pontiac Montana SV6

1 Answer

2006 Pontiac Montana SV6 Front heater only blowing warm. Rear heater blowing cold.


First off make sure the thermostat settings are set the same on the control panel for both front and rear units if thats ok it could b a few possibilities. 1 pluged heater core in rear 2 blocked heater hose try looking into these and see if it helps any

Dec 10, 2010 | 2006 Pontiac Montana SV6

3 Answers

Changing the front brake pads on a 2006 Pontiac Montana SV6


no that is only the older rear calipers on gm and others. the fronts do not have that style caliper and sound like the calipers are frozen and may be way your changing the pads. try opening the bleeder screw and then compressing them if they go then you need need brake hoses and if not you need calipers. god luck man

Dec 13, 2009 | 2005 Pontiac Montana SV6

1 Answer

2005 pontiac montana sv6 Is there a upgrade or brighter headlamp for this vehicle. as it stands now I am having difficultly in tracking them. Each headlamp has a high and low halogen lamp.(2) in the body


yes there is you may have to upgrade headlamp relay to handle the higher voltage bulb your local part`s should be able to help you with this i have seen kit`s in JC WHITNEY catalouges

Oct 07, 2009 | 2006 Pontiac Montana SV6

1 Answer

Changing headlamp on a 06 pontiac montana


There should be two or 3 wing nuts securing the headlamp assembly on. Remove the nuts and the housing should just slide out for you to change the bulb

Oct 05, 2009 | 2006 Pontiac Montana SV6

1 Answer

Real right turn signal light - Pontiac Montana SV6 2005


If the 2005 Montana is similar to the 2001 Montana, I have a solution. First you'll need a hexagonal wrench (the 6-sided L-shaped wrench). The tail light assembly is held on by two screws. You'll need the hexagonal wrench to remove them, because a normal screwdriver won't do it. I also had to use a conventional adjustable wrench to get the leverage to turn the hexagonal wrench, because the screws were in there pretty tight. Once you remove the two screws, the whole tail light assembly should come off. Mine required a little force and I had to play with it a bit, but it came off without a lot of work. There will be one set of wires that connects the tail light assembly to the rest of the minivan--try not to damage that set of wires. Once you get the tail light assembly off, you'll have to take apart the assembly that actually holds the lights. No tools should be required. It's held on by four plastic catches. Just undo the catches (easier said than done, but still not too tough) and it comes apart. Then you can pop out the old light and pop in the new light. Then re-assemble. For me, it went back together much easier than it came apart.

Dec 16, 2008 | 2005 Pontiac Montana SV6

Not finding what you are looking for?
2006 Pontiac Montana SV6 Logo

146 people viewed this question

Ask a Question

Usually answered in minutes!

Top Pontiac Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8202 Answers

Are you a Pontiac Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...