Question about 1999 Pontiac Grand Prix

2 Answers

Driverside window wont go up! motor works but seem like the control wires are not connected cables are loose can this be fixed

Posted by on

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 1,800 Answers

Hello Sir.
Welcme To Fixya's Community.


  1. Remove the rear door trim panel, as outlined in this section.
  2. Remove the plastic sheet water deflector.
  3. Remove the window-to regulator bolts by raising the window far enough to gain access to the bolts through the door metal.
  4. Raise and securely tape the window in the full up position.
  5. Detach the electrical connector.
  6. Remove the mounting bolts and remove the regulator from the door.
  7. If the motor is to be replaced, simply unbolt the motor from the regulator.

To install
  1. If the motor is to be replaced, install the motor to the regulator. The motor can be installed with the regulator in any position. Tighten the bolts to 89 inch lbs. (10 Nm).
  2. Install the regulator to the door and install the mounting bolts. To ensure proper orientation of the window regulator to the door, it is very important that the window regulator bolts are tightened in the specified sequence. Tighten the bolts to 89 inch lbs. (10 Nm) in this sequence.
    1. Lower Right
    2. Upper Right
    3. Lower Left
    4. Upper Left
  3. Attach the electrical connector.
  4. Carefully untape the window and lower the glass far enough to gain access to the bolts through the door metal. Tighten the bolts to 89 inch lbs. (10 Nm).
  5. Install the plastic sheet water deflector.
  6. Install the door trim panel, as outlined in this section.
Thank You For Using Fixya.

Please give a good feedback, also let me know if you need any further Info.
Good luck.

Fixe_You ^^

Posted on Jun 25, 2009

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 2,712 Answers

Yes

Posted on Jun 25, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

My 2002. Grandprix window wont work the motor works but theres like a cable loose in there


the cable or "ribbon" is what connects the window to the motor.

Mar 19, 2015 | Cars & Trucks

1 Answer

Hy driverside power window, driverside remote mirror and driver seat adustments do not work.


Have you check connection wireS, connector contact , finally the control switch ?
Using contact cleaner to clear dirt at connector, checking connector pins as we'll.
the wireS maybe broken ..

Aug 26, 2014 | 1998 Mercedes-Benz E-Class

1 Answer

Driverside window wont roll up put new motor on it


Are you getting power to the switch? Bad switch or broken wire at hinge cable.

Mar 15, 2014 | 2005 Chevrolet Colorado

1 Answer

The driverside window on 2008 nissan altima is not working


see the diagram and troubleshooting. God bless you

see for dirty, corrosion, oxide, bad contact, loose connector, switch faulty or dirty or bad contacts, motor faulty, LUBE in the system.

10_18_2012_5_35_16_am.gif

Oct 18, 2012 | Cars & Trucks

1 Answer

My driverside power window cable is bad, do I have to replace the whole motor and how do I connect the cables?


The cable is part of the window regulator and is replaced as an assembly.It may or may not come with a motor.

Apr 21, 2011 | 1999 Lincoln Town Car

1 Answer

Driver's side power window was inop. Window failed to go back up. Chevy dealer replaced the regulator motor and now working. Now the power dood lock switch on drivers side won't unlock doors.. Is the...


Hi, that wire is disconnected when the door panel is removed to work on the window motor. Take the car back and ask them to reconnect your door locks. If you want to fix it yourself, you may be able to access the connector by removing only the control panel where the door lock switch is installed. Remove any visible screws and then pry gently to pull up the panel. Odds are, however, that the whole door panel will need to be pulled loose to find the cable. You can possibly just pull the bottom of the panel loose, but do it carefully. Feed the wire back up to the control panel and reconnect to the switch. Thanks for using Fixya.

Jan 24, 2011 | 2003 Chevrolet Venture Passanger

1 Answer

Window stuck midway down on driver side driver switch control not working........how do i get to it to fix switch or motor or whatever may be the problem??


first remove door pannel and switch use test light at motor leave motor connected use a pin in oneterminal so you can attach test light ground end to pin place pointed end into other terminal doesnt matter which terminal basically place test licht in paralell use window switch testlight will light up if switch is ok and motor is deffective if no power to test light main switch on driverside is deffective

Jan 13, 2011 | 2002 Jeep Grand Cherokee

1 Answer

Window comes down but won't go back up


Since you hear the motor, it's probably the cable connecting the motor to the regulator, but the cable itself is not replaceable. The regulator and motor come as an assembly.

Jan 22, 2010 | 2000 Pontiac Grand Prix

2 Answers

Electric window


most likely the electric motor that raises and lowers the window is defective, u will need to remove the door panel and replace the window motor, about a 2 hour job and $100 in parts.

Apr 23, 2009 | 2003 Ford Focus

1 Answer

Driverside window won't go back up


I had to change the driver side switch in mine, also on a MonteCarlo. I think it was $40.
On the passenger door, the window came out of the track because the guide track rusted loose.

Feb 24, 2009 | 2000 Chevrolet Impala

Not finding what you are looking for?
1999 Pontiac Grand Prix Logo

371 people viewed this question

Ask a Question

Usually answered in minutes!

Top Pontiac Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8152 Answers

Are you a Pontiac Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...