Question about 1999 Dodge Durango

1 Answer

1999 dodge Durango 5.9 My abs pump would not shut off so my mechanic disconnected it. That took away my speedometer. I could not pass my Connecticut emissions test today because of the speedometer. Is it true i can just pull the #9 fuse under the hood?

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 25 Answers

No u need the abs pump hook back up because it controls your speed sensor for the dash

Posted on Jun 25, 2009

  • bsm240 Jun 25, 2009

    no u need the abs pump hook back up because it controls your speed sensor for the dash

  • bsm240 Jun 25, 2009

    no u need the abs pump hook back up because it controls your speed sensor for the dash

×

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1999 dodge durango abs pump stays running why???


may hav a bad abs module--dirty brake fluid causes it--expensive to replace---git car scanned or checked by specialist

Feb 06, 2013 | 1999 Dodge Durango

1 Answer

1999 durango the abs light and brake light comes on about 3 or 4 times in the past week as im driveing and then goes off in a few minutes i have new brakes and roters on the front and only rear wheel abs,...


did you check the speed sensor on the rear end on top of the rear end. this sensor works the speedometer the abs and break lights and power door locks

Aug 30, 2010 | 1999 Dodge Durango

1 Answer

Abs, brake lamp won't stay running


try to change the speed sensor and the differential sensor,good luck to change it cost of the parts is about 60 dollars both.

Aug 04, 2009 | 1999 Dodge Durango

2 Answers

1999 Dodge Durango. Brake Light and the ABS Light


If you backup lights are not working as well, I would say check the fuse for the backup lights, if the fuse is good, see if you are getting power to that fuse. We had this problem and after weeks of searching and changing sensors, we found the backup light fuse was good, but not getting power. Ran a wire from that fuse to the cig. lighter fuse and all woprksf great.

Jul 09, 2009 | 1999 Dodge Durango

1 Answer

P0500, intermittant speedometer, after sitting 6 months


Sounds speedmeeter is going haywire. Like everything in today's automobiles they are made with plastic gears. Some can be unscrewed under the stearing wheel others are not. The problem with the brake light break pads were probably stuck.I would say that your speedometer is not removable to many people disconnecting them for low milage on vehicle when trading or selling.

Jun 12, 2009 | 1999 Dodge Durango

2 Answers

ABS hydraulic control unit


Go to Module Master. I had the same problem sent mine in and came back. took less then 5 minutes to R/R. www.modulemaster.com

Prior to 2004, Durangos with 4 wheel ABS use the Kelsey Hayes Dodge controller attached to the hydraulic unit. Durangos with just rear wheel ABS use the Kelsey Hayes 125 located separately from the hydraulic unit.
2004 and later Durangos use the Bosch 5.4 controller.

Kelsey Hayes Dodge 1) Disconnect the negative battery cable.
2) Push the harness connector locks to release the locks, then remove the connectors from the CAB.
3) Disconnect the pump motor connector.
4) Remove screws attaching CAB to the HCU.
5) Remove the CAB.

Kelsey Hayes 125 1) Push the CAB harness connector lock to release the lock and remove the connector from the controller.
2) Remove the RWAL valve harness connector from the controller.
3) Remove the controller mounting screws and remove the controller from the mounting bracket.

Bosch 5.4 1) Pull out the side locking tab on the Bosch controller as shown.
2) Remove the connector.
3) Remove the 6 screws and separate the controller from the hydraulic unit.

durango.jpg 2008 Dodge Durango
kh_dodge_location.gif Kelsey Hayes Dodge Location
kh310_location.gif 1997 and earlier Durangos using the Kelsey Hayes 310
kh125_location.gif
Kelsey Hayes 125 controller for Dodge trucks with rear wheel ABS only

Jul 12, 2008 | 2000 Dodge Durango

Not finding what you are looking for?
1999 Dodge Durango Logo

292 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

75807 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22133 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8172 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...