Question about 1999 Chevrolet Lumina

1 Answer

Will not start

Would like to know location of crankshaft sensor

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Chevrolet Master
  • 2,984 Answers

It will be on the upper end of the motor...opposite of your pulleys...has a little wire harness connected to it.

Posted on Jun 24, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

3.1l. Where is the crankshaft position sensor?


Which one? There are two crankshaft position sensors on the 3.1L.
One is the 24X sensor. It is located behind the crankshaft pulley, installed into the timing cover. The other sensor, the 7X sensor (this is the one that is it fails will cause a no-start condition), is located on the outside of the engine block, close to the crankshaft.

Oct 25, 2015 | 1995 Chevrolet Lumina

1 Answer

Where is the 2nd crank shaft sensor located, and is there a diagram to show where these sensors are located?


is it a no crank or crank no start?
Possible causes for code P0335
- Faulty crankshaft position sensor
- Crankshaft position sensor harness is open or shorted
- Crankshaft position sensor circuit poor electrical connection
- Signal plate may be damage
- Starter motor may be faulty
- Starting system circuit
- Dead or weak battery

Read more: http://engine-codes.com/p0335.html#ixzz3Cxw6SN6O

Sep 10, 2014 | 2004 Buick Rendezvous

1 Answer

Location of crank position sensor for 1999 ford windstar 3.8 se


Crankshaft position sensor is mounted on the engine front cover next to the crankshaft trigger wheel, below electronic ignition coil pack on transmission housing .

Mar 29, 2014 | 1999 Ford Windstar

1 Answer

Need to know where the crank shaft sensor is located.


The Crankshaft Position Sensor is located under hood, center, rear engine area, mounted onpassenger side rear of cylinder head.

9_20_2011_5_58_25_pm.jpg

Fig. 2: View of the Crankshaft Position Sensor (CKP) location-2.2L engines


9_20_2011_5_58_48_pm.jpg

Fig. 3: The Crankshaft Position (CKP) sensor location-2.3L/2.4L engines


Hope this helps (remember to rate this free answer).

Mar 24, 2011 | 1997 Pontiac Sunfire

2 Answers

I can't find the location of the crankshaft postion sensor in my 2000 Hyundai sonata


My online Sonata manual shows these possibilities, but does not identify which applies specifically to 2000 Sonata.
Also, when you talk to the dealership parts counter, you'll need to know whether your 2000 Sonata is (a) 4-cylinder 2.4L MFI DOHC engine, or (b) 6-cylinder 2.5L MFI DOHC engine.
Its easy to tell - just count your spark plug wires.

-- begine excerpt from 2000 Hyundai Sonata Repair guide --

The crankshaft position sensor is located next to the flywheel.
The crankshaft position sensor is located next to the flywheel/torque converter.
The camshaft position sensor is located on the engine near the timing belt cover and under the upper radiator hose.
The crankshaft position sensor is located on the driver-s side of the vehicle, down by the lower radiator hose.
The crankshaft position sensor is located on the engine near the crankshaft pulley.
The crankshaft position sensor is located at the front of the engine near the timing belt.

--- end excerpt from 2000 Hyundai Sonata repai guide ---

Dec 29, 2010 | 2000 Hyundai Sonata

2 Answers

I need to put a crankshaft sensor but I don't Know its location I already changed the cam sensor. Ronnie


The crank sensor is located on the engine near the flywheel axis of the crankshaft.

Crankshaft Position Sensor Removal & Installation To Remove:
Location of the crankshaft position sensor on the 2.4L engine 90904g51.gif
Location of the crankshaft position sensor on the 3.0L engine 91154g20.gif
Location of the crankshaft position sensor on the 3.3L and 3.8L engines 91154g21.gif
NOTE: On the 2.4L engine, the crankshaft position sensor is mounted to the engine block behind the alternator, just above the oil filter. On the 3.0L, 3.3L and 3.8L engines, the crankshaft position sensor is mounted on the transaxle housing, above the vehicle speed sensor.
  1. Disconnect the negative battery cable.
  2. Raise and safely support the vehicle.
  3. Disconnect the crankshaft position sensor electrical connector.
  4. Unfasten the sensor mounting screw, then remove the sensor from the vehicle by pulling it straight out.
To Install:
NOTE: If the sensor removed is going to be re-installed, clean off the old spacer on the sensor face. A new spacer must be attached to the sensor face before installation. If the sensor is being replaced, be sure that a paper spacer is attached to the sensor face.
  1. Install sensor and push the sensor in until contact is made. While holding the sensor in this position, install and tighten the mounting bolt to 105 in. lbs. (12 Nm).
  2. Connect the crankshaft position sensor electrical connector.
  3. Lower the vehicle.
  4. Connect the negative battery cable.
prev.gif next.gif

Jul 31, 2010 | 1996 Plymouth Grand Voyager

1 Answer

Jsut want to know where crankshaft position sensor


Hi!!

here are illustrations of the CKP (crankshaft position) sensor in 2.3L and 3.0L.

Note: In the bottom of the 2.3L drawing says Trottle Position (TP) Sensor, this is wrong, It should say CKP Sensor.


2.3L Engine


The Crankshaft Position (CKP) sensor is located to the left of the crankshaft pulley.

0996b43f80202990.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Crankshaft Position (CKP) sensor location-2.3L engine


3.0L Engine


The Crankshaft Position (CKP) sensor is located just behind the crankshaft pulley on engine block.

0996b43f8020299e.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Crankshaft Position (CKP) sensor location-3.0L engine

The cost of the sensor is $23 bucks at AutoZone.

If helpful, click below

Apr 15, 2010 | 2002 Ford Escape

1 Answer

Need to know how to replace the crankshaft position sensor


Silverado, the crankshaft sensor is located behind the start, you have to remove the start to get access too. Raise the vehicle and remove the right front wheel, drop the start and move forward a little bit, this will expose the sensor
rate my answer please

Jul 07, 2009 | 2001 Chevrolet Silverado 2500HD

1 Answer

Crankshaft Position Sensor location 04 PT Cruiser


It is located behind the **** of the starter on the front of the engine starting in '03 the 2.4 lt was changes the repair manual failed to update this..you may sneak it out with small fingers with out pulling out the starter.

7e1821a.jpg

Feb 08, 2009 | 2004 Chrysler PT Cruiser

Not finding what you are looking for?
1999 Chevrolet Lumina Logo

Related Topics:

58 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8210 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...