Question about 1997 Dodge Dakota

1 Answer

How to take of the caliper - 1997 Dodge Dakota

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Contributor
  • 22 Answers

You can remove the caliper using a puller, which can be picked up at most auto parts stores for $10-15.
I would not recommend banging on it with a hammer.

Posted on Jun 24, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

3 Answers

How to install rear brake calipers on 79 pontiac firebird


Hello Allan,

Follow the link for the instructions your need to replace your rear brake calipers:



Repair Guides Front Disc Brakes Brake Caliper AutoZone com

Jul 27, 2016 | Pontiac Cars & Trucks

1 Answer

Front brakes sticking


It could be several reasons for this. 1. you have a caliper not releasing. the caliper piston not returning after the brakes released. 2. the caliper slides are rusty and dirty. I first would remove the calipers from both sides. clean the area where the caliper slides and the caliper holding bracket then put caliper grease on areas where the caliper meets metal.while the calipers are off you can check the brake pad wear. if you have one pad that shows more wear than the other pad you have a caliper problem and will need to be replaced

May 27, 2012 | Nissan Sentra Cars & Trucks

1 Answer

How do you compress the break caliper on a 2004 Kia sorento


IS THIS A REAR OR FRONT CALIPER?
1. FRONT CALIPER: INSERT A LARGE C CLAMP WITH THE SCREW END INTO OPEN BORE OF CALIPER PISTON, THE STATIONARY END SHOULD BE SNUG AGAINST THE CALIPER END HOUSING: THAT THE PISTON MOVES IN AND OUT OF
COMPRESS C-CLAMP UNTIL CALIPER PISTON SEATS FULLY AGAINST THE CALIPER SEAL. INSTALL NEW PADS
2. REAR CALIPER: RENT AT AUTOZONE A REAR DISC CALIPER COMPRESSION TOOL. THESE CALIPER PISTONS WIND IN CLOCKWISE, INSTEAD OF JUST SLIDING BACK INTO A SMOOTH BORE. THEY HAVE GROOVES THAT FOLLOW A MATCHING SET IN THE CALIPER HOUSING.
FURTHER QUESTIONS?....JLGPROP@YAHOO.COM

May 19, 2012 | 2004 Kia Sorento

1 Answer

Vibration in rear of vehicle when braks are applied


I believe that the rear discs are warped or the tires are out of round when braking. More likely, the discs. --- The following are the instructions for replacing the front and rear pads for the front/back rotors. 1999-01 Grand Cherokee Front
  1. Drain 2?3 of the brake fluid from the front reservoir. Use the bleeder screw at the front outlet port to drain the fluid. If equipped with anti-lock brakes, relieve the system pressure.
  2. Raise and safely support the vehicle.
  3. Remove the wheels.
  4. Insert a small prybar through the caliper opening and pry the caliper (using the outboard brake pad) to bottom the pistons in the caliper bore. NOTE: This will back the brake pads off of the rotor surface to facilitate the removal and installation of the caliper assembly.
  5. Pry the caliper support spring out of the caliper.
  6. Remove both caliper slide pin bushing caps and slide pins.
  7. Lift the caliper from the anchor.
  8. Using a piece of mechanics wire, support the caliper so there is not tension on the brake hose.
  9. Remove the brake pads from the caliper. Fig. 2: Installing the inward brake pad on the front caliper pistons - 1999-01 Grand Cherokee 93026g92.gif
    To install:
  10. Position the brake pads onto the caliper.
  11. Position the caliper into place on the anchor.
  12. Coat the caliper slide pins with silicone grease and torque them to 21-30 ft. lbs. (29-41 Nm). Install the slide pin bushing caps.
  13. Install the caliper support spring in the top of the caliper under the anchor; then, install the other end into the lower caliper hole. NOTE: Hold the spring in the caliper hole with your thumb while prying the spring end out and under the anchor.
  14. Fill the master cylinder with fluid and bleed the brake system.
  15. Before driving the vehicle, pump the brakes several times to seat the pads.
  16. Install the wheels.
Rear
  1. Drain 2?3 of the brake fluid from the front reservoir. Use the bleeder screw at the front outlet port to drain the fluid. If equipped with anti-lock brakes, relieve the system pressure.
  2. Raise and safely support the vehicle.
  3. Remove the wheels.
  4. Insert a small prybar through the caliper opening and pry the caliper (using the outboard brake pad) to bottom the piston in the caliper bore. NOTE: This will back the brake pads off of the rotor surface to facilitate the removal and installation of the caliper assembly.
  5. Pry the caliper support spring out of the caliper.
  6. Remove both caliper slide pin bushing caps and slide pins.
  7. Lift the caliper from the anchor.
  8. Using a piece of mechanics wire, support the caliper so there is not tension on the brake hose.
  9. Remove the brake pads from the caliper. Fig. 3: Installing the inward brake pad on the rear caliper piston - 1999-01 Grand Cherokee 93026g95.gif
    To install:
  10. Position the brake pads onto the caliper.
  11. Position the caliper into place on the anchor.
  12. Coat the caliper slide pins with silicone grease and torque them to 21-30 ft. lbs. (29-41 Nm). Install the slide pin bushing caps.
  13. Install the caliper support spring in the top of the caliper under the anchor; then, install the other end into the lower caliper hole. NOTE: Hold the spring in the caliper hole with your thumb while prying the spring end out and under the anchor.
  14. Fill the master cylinder with fluid and bleed the brake system.
  15. Before driving the vehicle, pump the brakes several times to seat the pads.
  16. Install the wheels.

Sep 30, 2010 | 2000 Jeep Grand Cherokee

1 Answer

Will I need a caliper reset tool kit to change the brakes on my 2007 toyota sienna or will a standard c-clamp do the job? And since it is an ABS system, I assume that brakes must be bled, correct?


Brake Pads Removal & Installation Front To Remove:
  1. Remove the front wheels. Front brake caliper (exploded view) toyota-09-00-5838.gif

  2. Loosen the caliper bleeder.
  3. Hold the slide pin; remove the 2 mounting bolts and remove the brake caliper from the support.
  4. Support the caliper.
  5. Open the brake bleeder. Press the caliper piston into the bore.
  6. Close the bleeder after the piston has reached the bottom of the caliper bore.
  7. Remove the brake pads, support plates, wear indicators and anti squeal shims.
  8. Remove the slide pins and bushings from the caliper support.
To Install:
  1. Lubricate the slide pins and bushings with brake grease.
  2. Install the bushing on the slide pin.
  3. Install the slide pin on the caliper support.
  4. Install the brake pad support plates on the caliper supports.
  5. Lubricate the anti squeal shims with brake grease.
  6. Install the anti squeal shims on the brake pads.
  7. Install the pad wear indicator facing upward and install the pads on the caliper support.
  8. Install the caliper on the support.
  9. Install the 2 mounting bolts, hold the slide pins and tighten 25 ft-lb (34 Nm).
  10. Fill the reservoir and bleed the brakes.
  11. Install the front wheels.
Rear To Remove:
  1. Remove the rear wheels.
  2. Loosen the caliper bleeder. Rear brake caliper (exploded view) toyota-09-00-5842.gif

  3. Hold the slide pin; remove the 2 mounting bolts and rear brake caliper assembly from the support.
  4. Support the caliper.
  5. Open the brake bleeder. Press the caliper piston into the bore.
  6. Close the bleeder after the piston has reached the bottom of the caliper bore.
  7. Remove the brake pads, support plates, and anti squeal shims.
  8. Remove the slide pins from the caliper support.
To Install:
  1. Lubricate the slide pins with brake grease.
  2. Install the slide pin on the caliper support.
  3. Install the brake pad support plates on the caliper supports.
  4. Lubricate the anti squeal shims with brake grease.
  5. Install the anti squeal shims on the brake pads.
  6. Install the rear pads on the caliper support.
  7. Install the rear caliper on the support.
  8. Install the 2 mounting bolts, hold the slide pins and tighten 25 ft-lb (34 Nm).
  9. Fill the reservoir and bleed the brakes.
  10. Install the front wheels.
prev.gif next.gif

Sep 18, 2010 | 2007 Toyota Sienna

1 Answer

Need help changing brake pads and routers on 2003


Remove brake fluid from the master cylinder brake fluid reservoir until the reservoir is approximately 1/2 full. Discard the removed fluid.
  1. Raise and safely support the front of the vehicle. Remove the front wheels.
    1. Remove or disconnect the following:
    2. Front brake caliper guide pin bolts
    • Brake caliper by slowly sliding it up and off the adapter and brake rotor. Support the caliper out of the way with a strong piece of wire. Do not let the caliper hang by the brake hose or damage to the brake hose will result.
    1. If necessary, compress the caliper piston into the bore using a C-clamp. Insert a suitable piece of wood between the C-clamp and caliper piston to protect the piston.
    2. Outboard disc brake pad from the caliper by prying the brake pad retaining clip over the raised area on the caliper. Slide the brake pad down and off the caliper.
    • Inboard disc brake pad from the caliper by pulling the brake pad away from the caliper piston until the retaining clip on the pad is free from the caliper piston cavity
  • To install:
    1. Be sure the caliper piston has been completely retracted into the piston bore of the caliper assembly. This is required when installing the brake caliper equipped with new brake pads.
    2. If equipped, remove the protective paper from the noise suppression gaskets on the new disc brake pads.
    3. Install or connect the following:
      • New inboard disc brake pad into the caliper piston by pressing the pad firmly into the cavity of the caliper piston. Be sure the new inboard brake pad is seated squarely against the face of the brake caliper piston.
      • Outboard disc brake pad by sliding it onto the caliper assembly
      • Brake caliper assembly over the brake rotor and onto the steering knuckle adapter
      • Caliper guide pin bolts and torque to: 35 ft. lbs. (47 Nm) on 2002–04 models or 26 ft. lbs. (35 Nm) on 2005 models
      • Front. Apply the brake pedal several times until a firm pedal is obtained.
    4. Check the fluid level in the master cylinder and add fluid as necessary. Road-test the vehicle.

    For the rotors:

    1. Remove brake fluid from the master cylinder brake fluid reservoir until the reservoir is approximately 1/2 full. Discard the removed fluid.
    2. Raise and safely support the front of the vehicle. Remove the front wheels.
    1. Remove or disconnect the following:
    2. Front brake caliper guide pin bolts
    • Brake caliper by slowly sliding it up and off the adapter and brake rotor. Support the caliper out of the way with a strong piece of wire. Do not let the caliper hang by the brake hose or damage to the brake hose will result.
    1. If necessary, compress the caliper piston into the bore using a C-clamp. Insert a suitable piece of wood between the C-clamp and caliper piston to protect the piston.
    2. Outboard disc brake pad from the caliper by prying the brake pad retaining clip over the raised area on the caliper. Slide the brake pad down and off the caliper.
    • Inboard disc brake pad from the caliper by pulling the brake pad away from the caliper piston until the retaining clip on the pad is free from the caliper piston cavity
  • To install:
    1. Be sure the caliper piston has been completely retracted into the piston bore of the caliper assembly. This is required when installing the brake caliper equipped with new brake pads.
    2. If equipped, remove the protective paper from the noise suppression gaskets on the new disc brake pads.
    3. Install or connect the following:
      • New inboard disc brake pad into the caliper piston by pressing the pad firmly into the cavity of the caliper piston. Be sure the new inboard brake pad is seated squarely against the face of the brake caliper piston.
      • Outboard disc brake pad by sliding it onto the caliper assembly
      • Brake caliper assembly over the brake rotor and onto the steering knuckle adapter
      • Caliper guide pin bolts and torque to: 35 ft. lbs. (47 Nm) on 2002–04 models or 26 ft. lbs. (35 Nm) on 2005 models
      • Front. Apply the brake pedal several times until a firm pedal is obtained.
    4. Check the fluid level in the master cylinder and add fluid as necessary. Road-test the vehicle.

    May 28, 2010 | 2003 Chrysler Town & Country

    2 Answers

    How do you remove the rear brake caliper on 1996 mercury grand marquis


    Removal & Installation
    1. Raise and safely support the vehicle.
    2. Remove the rear wheel and tire assembly.
    3. Remove the brake fitting retaining bolt from the caliper and disconnect the flexible brake hose from the caliper. Plug the hose and the caliper fitting.
    4. Remove the caliper locating pins. Lift the caliper off the rotor and anchor plate using a rotating motion.

    WARNING Do NOT pry directly against the plastic piston or damage to the piston will occur.



    005ba8a.gif
    Rear disc brake caliper removal


    1aff680.gif
    Rear disc brake caliper installation

    To install:
    1. Position the caliper assembly above the rotor with the anti-rattle spring located on the lower adapter support arm. Install the caliper over the rotor with a rotating motion. Make sure the inner pad is properly positioned.
    2. Install the caliper locating pins and start them in the threads by hand. Tighten them to 19-26 ft. lbs. (26-35 Nm).
    3. Install the brake hose on the caliper with a new gasket on each side of the fitting outlet. Insert the retaining bolt and tighten to 30-40 ft. lbs. (40-54 Nm).
    4. Bleed the brake system, install the wheel and tire assembly and lower the vehicle.
    5. Pump the brake pedal prior to moving the vehicle to position the linings.
    6. Road test the vehicle.

    May 23, 2010 | 1996 Mercury Grand Marquis

    2 Answers

    How do I replace rear brake pads on a 2004 Olds


    find out what tool you need to remove bolts for the caliper(2) once you get the bolts out remove caliper. next step remove old pads.then you will need a c clamp to compress piston on the caliper back in then get new pads and install them on caliper easy fix reinstall caliper on to rotor and put bolts back in just observe how the caliper came off

    Jan 10, 2010 | 2004 Oldsmobile Alero

    1 Answer

    Need the correct torque specs for 2004 silverado 1500 calipers


  • Tighten the 2 brake caliper mounting bolts to 108 Nm (80 ft. lbs.) . Caliper Mounting Bracket to Knuckle, Front (15 series) 175 Nm (129 ft. lbs.) Caliper Mounting Bracket to Knuckle, Front (25/35 series) 300 Nm (221 ft. lbs.) Brake Caliper Mounting Bolt Rear (15 series) 42 Nm (31 ft. lbs.) Brake Caliper Mounting Bolt Rear (25/35 series) 108 Nm (80 ft. lbs.) Caliper Mounting Bracket Bolt Rear (JC5/JH5) 200 Nm (148 ft. lbs.) Caliper Mounting Bracket Bolt Rear (JH6) 165 Nm (122 ft. lbs.) Caliper Mounting Bracket Bolt Rear (JH7) 300 Nm (221 ft. lbs.) Caliper Mounting Bracket Bolt Rear (NYS) 200 Nm (148 ft. lbs.)
    hope this helps
  • Mar 28, 2009 | 2004 Chevrolet Silverado

    1 Answer

    Front brake pad replacement


    black caliper and black caliper bracket = ATE (Teves), the other color is Akebono. To replace pads, use a screwdriver to stick into slot to pry caliper open a bit. Remove 2 caliper pins (under plastic caps on rubber caliper boots.) Lift caliper from rotor. Remove old pads. Wipe caliper anti-squeak onto back of new pads, and place pads into caliper. Replace caliper onto rotor and bracket. Insert pins and tighten securely (you can lubricate the pins) Replace plastic boot covers. Install wheels. Lower vehicle.

    Jul 16, 2008 | 2000 Jeep Grand Cherokee

    Not finding what you are looking for?
    1997 Dodge Dakota Logo

    Related Topics:

    44 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Dodge Experts

    yadayada
    yadayada

    Level 3 Expert

    75822 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22156 Answers

    Jeff Turcotte
    Jeff Turcotte

    Level 3 Expert

    8202 Answers

    Are you a Dodge Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...