How to remove oil pan from 1995 Ford E-150 van

www.ask.com/mfg.name/make/model#/how-to-remove-oil-pan-without-lifting-the-engine/

www.youtube.com/mfg.name/make/model/removing oil pan without lifting the motor/

www.wikipedia.org/mfg.name/make/model/removing/oil_pan/without/lifting/the/engine/

www.howto.com/
www.infolinks.com/
/mfg.name/make/model/removing oil pan without lifting the engine/

Disconnect the motor mounts and jack the engine to remove the oil pan. Remove the oil pan, replace the oil pump you'll find at the end of a pick up tube, replace the pump and put the pick up tube back on the new pump making sure it's in the same low position it was when removed, replace the oil pan gasket and put the oil pan back on, lower the engine and put the motor mount bolts back in. Put in the proper amount of oil and go.

you mite have to remove the motor mounts so that you can pick up on motor just a little.. a couple of inch.. then take off the oil pan bolts

Yes you can do it yourself.
Its not very easy,but with basic Auto repair tools the task can be easily completed.

=========
There are few help links with solutions to complete these task.
I suggest you to refer these links and view its procedure.

-------
Click the link below:----
------------
How to Replace an Oil Pan Gasket?
http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-oil-pan-gasket.html
-----------
KIA Sportage leaking oil from oil pan?

Go to Newly Launched

FREE Car repair guobyme.blogspot.com/2011/11/kia-sportage-leaking-oil-from-oil-pan.html" http://howtobyme.blogspot.com/2011/11/kia-sportage-leaking-oil-from-oil-pan.html
----------------
Oil pan Gasket on 1998 Toyota Tercel?
http://howtobyme.blogspot.com/2011/11/oil-pan-gasket-on-1998-toyota-tercel.html
-------------
VALVE COVER GASKET REMOVAL GUIDE http://technoanswers.blogspot.in/2012/06/valve-cover-gasket-removal-guide.html
--------- Car oil leaks from valve cover gasket? http://schematicsdiagram.blogspot.com/2011/12/car-oil-leaks-from-valve-cover-gasket.html

------------
How to replace Oil Pan on 2008 Honda Odyssey?

http://schematicsdiagram.blogspot.com/2011/12/how-to-replace-oil-pan-on-2008-honda.html

-----------
How to replace Oil Pressure Sensor on 2008 Honda Odyssey?

http://schematicsdiagram.blogspot.com/2011/12/how-to-replace-oil-pressure-sensor-on.html

------------
2004 Chevrolet Express Van: Oil pressure sending unit replacing? http://whoisbyme.blogspot.in/2012/06/2004-chevrolet-express-van-oil-pressure.html
-------------
HOW TO REPLACE AN OIL PUMP
http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-oil-pump.html
-------------
HOW TO CHANGE ENGINE OIL AND FILTER
http://schematicsdiagram.blogspot.com/2011/07/how-to-change-engine-oil-and-filter.html
--------------
HOW TO REPLACE AN OIL PRESSURE SWITCH (SENSOR)
http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-oil-pressure-switch.html

-------------

How to Check Differential Oil Leaks and Replace Oil
http://schematicsdiagram.blogspot.com/2011/07/how-to-check-differential-oil-leaks-and.html
-----------
HOW TO PERFORM A BASIC ENGINE TUNE UP-OIL CHANGE
http://schematicsdiagram.blogspot.com/2011/08/how-to-perform-basic-engine-tune-up-oil.html

----------
HOW TO RESET OIL CHANGE INDICATOR? http://whoisbyme.blogspot.in/2012/07/how-to-reset-oil-change-indicator.html

------------
These details will help.
Thanks.

soak it in engine oil for a day or so then it will move

on a van yes!!! you may also have to remove the intake and assorted hardware, even then you may have to reach between the oil pan and the engine to remove the oil pump just to get the pan out

Yes it can. It can be replaced from the underside by removing the oil pan

You should be able to drop the pan by removing the bolts. On some vehicles it is necessary to jack the engine up after removing the bolts from the engine mounts. If this is necessary then once you have your engine up high enough (usually 3 to 4 inches) put small blocks of wood where the mount would go to support the engine while you remove the oil pan. Also you can work the oil pan gasket around the oil pickup tube with the pan down with out having to totally remove the pan from underneathe the truck. If you do this just make sure the gasket is not twisted before reinstalling the pan onto the engine.

Do you need to remove the oil pan to change the pan or just the gasket?

done this on several i-6 f-150s. slide back or remove transmission, remove motor mount bolts from frame(not motor), jack motor up as far as possible without damaging egr valve or wiper motor when they hit, shim under motor mounts so that when you drop the jack the motor does not come back down any(the motor is well balanced on the mounts, it will not fall out of the truck like a v8 will), then remove the oil pan. you May have to remove the pickup tube(usually not), and you May have to rotate the crankshaft so that the lobes clear the oil pan. this is a common problem with these trucks due to the size of the oil pan(Huge), and the minimum pan to crossmember clearance