Question about 1998 GMC Jimmy

1 Answer

Want to know what the torque specs are for the idler arm, pitman arm and bearing hub and tie rods? for a 1998 gmc envoy 4x4 automatic

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

2000 gmc jimmy front cv axle nut (36 mm) torque ratings?

Posted on Jul 15, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Steering wheel has to much play


Idler arm and or pitman arm most common.could also be excessive play in steering gear box.Tie rods/center link but usually its my first 2 choices go bad bothe of them idler and pitman common wear parts.

Aug 30, 2012 | 1997 GMC Jimmy

1 Answer

Need the torque specs for the nuts on the pitman arm stud and the idler arm stud (nuts that hold the linkage on the studs) for a 2003 sierra 1500HD, 4wd, 6.0L, crew cab


pit man arm to steering gear nut 186 ft lbs.

pit man arm to relay rod nut 46 ft lbs.

idler arm to frame nut 73 ft lbs.

idler arm to relay rod nut 46 ft lbs.

May 08, 2011 | 2002 GMC Sierra 1500HD

3 Answers

2006 chevy silverado 1500 4x4,i cant adjust the power steering?with the bolt and lock nut with exagone screw?excuse my english,iam speak french.thank,luc


Why are you messing with it in the first place?? This is a job for someone who knows what they are doimg,,like a wheel alignment garage.

Mar 16, 2011 | 2006 Chevrolet Silverado

2 Answers

My 94 Silverado pulls very hard to the right, and is eating up my front left tire like nothing. what other than alignment can be going wrong?


You could have a bad tie rod end, Idler arm, pitman arm, wheel bearing or ball joint. All of these will normally cause a vibration also. Check by jacking the front end one side at a time and moving the tire back and forth on front and back and in and out on top and bottom. Either watch or have someone else watch the steering assembly for movement and where it is. If there is no unusual movement, it is more than likely an alignment problem or tire problem.

Oct 20, 2010 | 1994 Chevrolet C1500

1 Answer

Is a special tool required to remove inner tie rod from relay rod on 2001 Tahoe.? Also what should torque be?


Relay Rod Removal & Installation To Remove:
  1. Raise and support the vehicle
  2. Remove or disconnect the following:
    • Engine protection shield, if equipped
    • Steering damper from the relay rod, if equipped Note: Use the proper tool in order to separate all the tie rods and the ball joints.
      Steering components gm_trk_sub15_steering_components.gif

    • Tie rod ends (F) (See: Tie Rod Ends)
    • Idler arm ball stud nut (J) and discard the nut (See: Idler Arm)
    • Pitman arm nut (H) and discard the nut (See: Pitman Arm) Remove the idler arm from the relay rod gm_trk_sub15_idler_from_relay_rod.gif

    • Relay rod from the idler arm ball stud using the J24319-B or other suitable puller Remove relay rod from pitman arm ball stud gm_trk_sub15_relay_rod_rem.gif

    • Relay rod from the pitman arm ball stud using the J24319-B or other suitable puller
    • Relay rod from the vehicle
  3. Inspect the threads on the tie rod ends for damage
  4. Inspect the ball stud threads for damage
  5. Inspect the ball stud seals for excessive damage
  6. Clean the threads on the ball studs
To Install:
  1. Install or connect the following:
    • Relay rod to the vehicle
    • Relay rod to the pitman arm ball stud
    • Relay rod to the idler arm ball stud and make sure the seal is on the stud
    • New pitman arm prevailing torque nut
    • New idler arm prevailing torque nut and tighten the idler arm and pitman arm nuts; Torque to: 46 ft. lbs. (62 Nm)
    • Tie rod ends
    • Steering dampener to the relay rod, if equipped
    • Engine protection shield, if equipped
  2. Lower the vehicle
  3. Check the wheel alignment
  4. Test drive the vehicle to confirm the repairs
prev.gif next.gif

Sep 18, 2010 | 2001 Chevrolet Tahoe

1 Answer

How to replace a idler arm and pitman arm need to replace it on my 98 gmc suburban 4x4


You will need the proper tools to remove them which can be rented at auto parts stores. The pitman arm has to pulled off with an pitman arm puller also have to drop steering box I believe to change it. I know we did on my 1996 Tahoe the idler arm can be seperated with a front end fork also available at parts store. You just drive it between the idler arm and tie rod after removing castle nut and cotter pen.

Jul 17, 2010 | 1998 GMC Suburban

1 Answer

How to change the pittman arm and idler arm on a 1999 S10 Chevy Blazer 4x4?


Pitman arm requires a pitman arm puller, and a tie rod seperator or "pickle fork". Remove the cotter pin on from the joint on the pitman arm and center link, then remove the nuts from both ends of pitman arm. Use the pitman arm puller to remove the pitman arm from the steering gear, then use the tie rod seperator to remove the end from the center link. Reinstall and retighten nuts, do not leave out the cotter pin.
Idler arm will require tie rod seperator. Remove the cotter pin from the end at the center link, use the tie rod seperator to seperate the joint there. Unbolt the idler arm from the frame, and remove. On reinstalling remember to install a new cotter pin. It would be best to have the front end alignment checked after replacing these parts.

Apr 08, 2010 | 1999 Chevrolet S-10 Pickup

2 Answers

I HAVE A 1998 GMC JIMMY 4X4 .. IT SEEMS AS THOUGH WHEN I PUT IT IN 4 WHEEL DRIVE IT PULLS ALL OVER THE ROAD . IT KINDA FEELS LIKE IM DRIVING AGAINST SOMEONE .. I HAD MY UPPER AND LOWER BALL JOINTS DONE AND...


inspect frt end tie rods,idler arm,pitman arm,inner tie rods,steeringbox,control arms upper and lower bushings.1or more of these parts could be worn

Feb 25, 2009 | 1998 GMC Jimmy

Not finding what you are looking for?
1998 GMC Jimmy Logo

640 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

Marvin
Marvin

Level 3 Expert

81294 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...