Question about 1999 Dodge Caravan

1 Answer

Fuel emergancy shut off switch for 99 dodge caravan

I had a misshap were my front tire blew ripped the fron bumper off! And now when i start the van it runs for 5 seconds and stops! Its almost like the fuel emergancy switch turned on! the question were is the emergancy fuel shut off switch on my 99 carvan?

Posted by on

  • gerry bissi May 11, 2010

    read owners anual for location

×

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 721 Answers

It's not the fuel shut off. It wouldn't run at all. There's many things to check yet.

Posted on Jun 24, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Right front tire blew out, some one said the fuel line fuse shut down cause the van not start back on


to prove this check the fuse . If it has blown then check for wiring damage caused by the tyre case as it passed under the car. If it stayed on the rim intact then it will just be a coincidence . Run the fault codes to find which sensor was affected

Sep 10, 2014 | Cars & Trucks

1 Answer

Front passenger tire wobbles when slowing down van 2011 ecoline van


Wheel disc warped and loose wheel bearing start with discs

Mar 14, 2014 | 1998 Ford Econoline

2 Answers

05 buick lesabre steering wheel schimmy at 5 mph


My first guess would be a bad tire. You could have the tires rotated front to back to see if the problem stops.

Mar 04, 2014 | 2002 Buick LeSabre

1 Answer

Mazda CX7 front bumper removal


start with the small screws on the bottom, then take off the splash shields running in front of the tires. open the hood and pop the center out of the two big clips by the headlamps, the two big Philips screws on the rad support and finally get someone to help you pull it off. Slowly start from one side and make sure to unplug all of the lights before any tension gets on them. have some carboard or a tire ready to place it on without scratching it

Jul 13, 2013 | Mazda CX-7 Cars & Trucks

1 Answer

Reset tire pressure sensor


My work van is a e-series 2011 cargo / work van, the way to reset the tire pressure on it is too push the hazard lights button a few times, may 5 or 6 times pretty quickly when the van is in park and running, the horn will honk and and then you stop pushing the hazard button and wait for a few minutes and the horn will honk agian and the tire pressure light will go out, i dont know if this resets the tires pressure sensor, but the light on the dash goes out, on my van it comes back on after i restart the van , so I am guessing that the sensor on my van is bad. but its worth a shot on your car.

Feb 09, 2012 | Ford E-Series Van Cars & Trucks

1 Answer

Have a problem with starting battery strong was driving on the rim and the van stopped


there may be an emergancy fuel shutoff switch... which may have been actuated when the vans tire blew and tilted the van and shook the van....?

Sep 24, 2010 | 1998 Toyota Sienna

2 Answers

How to reset the tire pressure on a 08' chevy tahoe?


TPMS Sensor Matching Procedure

Each TPMS sensor has a unique identification code. Any time you rotate your vehicle's tires or replace one or more of the TPMS sensors, the identification codes will need to be matched to the new tire/wheel position. The sensors are matched to the tire/wheel positions in the following order: driver side front tire, passenger side front tire, passenger side rear tire, and driver side rear tire using a TPMS diagnostic tool. See your dealer/retailer for service.

The TPMS sensors can also be matched to each tire/wheel position by increasing or decreasing the tire's air pressure. If increasing the tire's air pressure, do not exceed the maximum inflation pressure indicated on the tire's sidewall.

To decrease air-pressure out of a tire you can use the pointed end of the valve cap, a pencil-style air pressure gage, or a key.

You have two minutes to match the first tire/wheel position, and five minutes overall to match all four tire/wheel positions. If it takes longer than two minutes, to match the first tire and wheel, or more than five minutes to match all four tire and wheel positions the matching process stops and you need to start over.

The TPMS sensor matching process is outlined below:

  1. Set the parking brake.
  2. Turn the ignition switch to ON/RUN with the engine off.
  3. Press the Remote Keyless Entry (RKE) transmitter's LOCK and UNLOCK buttons at the same time for approximately five seconds. The horn sounds twice to signal the receiver is in relearn mode and TIRE LEARNING ACTIVE message displays on the DIC screen.
  4. Start with the driver side front tire.
  5. Remove the valve cap from the valve cap stem. Activate the TPMS sensor by increasing or decreasing the tire's air pressure for five seconds, or until a horn chirp sounds. The horn chirp, which may take up to 30 seconds to sound, confirms that the sensor identification code has been matched to this tire and wheel position.
  6. Proceed to the passenger side front tire, and repeat the procedure in Step 5.
  7. Proceed to the passenger side rear tire, and repeat the procedure in Step 5.
  8. Proceed to the driver side rear tire, and repeat the procedure in Step 5. The horn sounds two times to indicate the sensor identification code has been matched to the driver side rear tire, and the TPMS sensor matching process is no longer active. The TIRE LEARNING ACTIVE message on the DIC display screen goes off.
  9. Turn the ignition switch to LOCK/OFF.
  10. Set all four tires to the recommended air pressure level as indicated on the Tire and Loading Information label.
  11. Put the valve caps back on the valve stems.

Jul 28, 2009 | 2008 Chevrolet Tahoe

1 Answer

Hole in front bumper of Infiniti I30 2001


Sure. Use bondo. Do you have a paint sprayer?

Most composite bumpers have the paint in the composite, but I dont' know why, at least for a coupe or three years, the bumper wouldn't hold paint sprayed on.

May 05, 2009 | Hyundai Motor 2004 Sonata

1 Answer

1994 Plymouth Voyager Van


u need to raise up the van then once your underneath it u should find the starter going from the left tire to the right tire either closer to the front bumper or the firewall..most likely closer to the back of the engine by the firewall then once you find it its only a thick wire and a few bolts and it should fall out

Oct 26, 2008 | 1994 Plymouth Voyager

Not finding what you are looking for?
1999 Dodge Caravan Logo

Related Topics:

600 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

76132 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8273 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...