Question about 2004 Hummer H2

1 Answer

2003, h2. how do i remove old stock head lamp form grill ?Already removed the nuts on inside. lamp will not push through.I do not want to force it, thats why I am asking.

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 9 Answers

IS THE CROME GRILL IN THE WAY ON THE OUTSIDE

Posted on Jul 15, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Detailed instructions on front bumper removal. NOTE: From all the videos, it appears the CAB is different than the sedan. An example is the grill does NOT come up with the hood.


Remove wheels. Remove fender liners front. Remove three nuts per side from inside fender wells. Remove fog lamp grilles. Remove vertical bolt just inside grilles--pointing up. Remove two screws per side under hood near front of fender. Put milk crate under front bumper. Remove belly pan first. Slide bumper forward onto milk crate, disconnect headlight washer line at quick disconnect if so equipped. Disconnect fog light connectors. Remove bumper.

Oct 16, 2015 | 2003 Audi A4 Cabriolet

1 Answer

How to remove an old headlamp on a 2003 rav4?


The lamp, or the entire housing?

The lamp is tight, but not hard. It is under the rubber cap on the back of the housing. It's tight with other items, but it can be done without removing anything. Unplug the lamp, remove the rubber cap, release the wire bail, and remove the lamp.

The housing is a major pain. You need to remove the grille and the trim strip that runs under the headlights and grille. It is retained by a couple of hidden plastic clips at each end, you need a pair of small screwdrivers to depress the locking pins to release them. Wrap the screwdrivers so you don't mar the paint.

Once that is out of the way, work around the housing and remove any bolts attaching it, then work the housing out of the fender.

Jun 14, 2014 | 2003 Toyota RAV4

1 Answer

Daytime running light


Disconnect the electrical connector from the back of the lamp assembly.Remove the nuts.Disengage the clip retaining the lamp and remove the lamp from the bumper.Turn the socket counter clockwise and remove the bulb.Reverse procedure to reinstall the lamp assembly.Hope this helps.Good luck.

Feb 22, 2012 | 2005 Hummer H2

1 Answer

How to replace head lights on a 2008 cadilac dts


Turn off your Cadillac CTS and look below the front grille for the bottom pins that hold it in place. Push these pins inward to disengage them.

  • 2 Open the hood. Look for the pins that hold the grille in place on the engine compartment side. Push in these pins. Pull the grille off the front of the Cadillac CTS.
  • 3 Remove the side pins from the CTS fender on the side that has the headlight you wish to replace. Pull the side fender away from the vehicle to prepare for removing the headlight.
  • 4 Remove the three bolts on the top and rear of the headlight.
  • 5 Disconnect the wiring harness from the back of the headlight.
  • 6 Push or pull the headlight through the front of the Cadillac CTS and set it aside. This part may require a lot of force if the headlight is stuck.
  • 7 Insert the new headlight along the runners upon which the previous headlight sat, and attach the wiring harness. Reinstall the three bolts you removed earlier, as well as the side finder and the grille.
  • Dec 06, 2011 | Cars & Trucks

    1 Answer

    Need to change out a broken tail light cover for a 2002 mercury sable


    Replacing tail/brake/turn signal/backup lamp bulbs (page 59-60 of owners manual)

    Sedan

    The tail lamp, brake lamp, turn

    signal lamp and backup lamp bulbs

    are located in the same portion of

    the tail lamp assembly. Follow the

    same steps to replace either bulb.

    1. Make sure headlamp switch is in

    OFF position and open trunk and

    remove two plastic mushroom nuts,

    three push pins and the plastic

    cover from inside the trunk to

    access the lamp assembly.

    2. Carefully pull the carpet away to

    expose the lamp assembly hardware.

    3. Remove four nut and washer

    assemblies and the lamp assembly

    from the vehicle.

    4. Remove the bulb socket by

    rotating it counterclockwise, then

    pulling it out of the lamp assembly.

    5. Pull the bulb from the socket and
    push in the new bulb.

    6. Install the bulb socket into the lamp assembly by rotating it clockwise.

    7. Install the lamp assembly on the vehicle with four nut and washer

    assemblies ensuring the washers on the nuts are flush with the body to

    prevent water from entering the trunk.

    8. Carefully push the carpet back in to place and install the plastic cover
    inside the trunk with three push pins and two plastic mushroom nuts.

    May 31, 2011 | Mercury Sable Cars & Trucks

    1 Answer

    I am looking for a diagram of the bumper assembly for a 2004 Chrysler town & country.


    Hope this helps, it it does please leave feedback and vote Thank You and Good Luck


    1. Release hood latch and open hood.
    2. Remove the headlamp assemblies.
    3. Hoist vehicle and support with safety stands.
    4. Remove the five push pin fasteners attaching bottom of fascia/air dam to radiator closure panel.
    5. Remove front wheels.
    6. Remove front wheelhouse splash shields fasteners as necessary to gain access to bolts attaching front fascia to fender.
    Fig. 1 133387737
    Fig. 2 133387738

    1. Remove the two bolts and two nuts attaching fascia to the front fenders (Fig. 1) and (Fig. 2).
    2. Disconnect fog lamp wire connectors, if necessary.
    3. Lower vehicle.
    4. Remove two bolts attaching the upper grille support to the headlamp mounting panel at each side of the grille.
    5. Remove bumper fascia from vehicle.
    INSTALLATION


    1. Position front bumper fascia on vehicle (Fig. 1) and (Fig. 2).
    2. Install the two bolts attaching fascia to headlamp mounting panel at each side of grille.
    3. Hoist vehicle and support with safety stands.
    4. Install the two bolts and two nuts attaching fascia to the front fenders. The fascia should be flush to fender.
    5. Install front wheelhouse splash shields fasteners.
    6. Install front wheels.
    7. Connect fog lamp wire connectors, if necessary.
    8. Install the five push pin fasteners attaching bottom of fascia to radiator closure panel.
    9. Lower the vehicle.
    10. Install the headlamp assemblies.

    Jan 02, 2011 | Chrysler Town & Country Cars & Trucks

    1 Answer

    2003 escalade how to remove front bumper.


    I just took this one on today. You'll need a flat head screw driver (a clip puller if you have one) a 15mm socket with a 10" extension and 10mm socket. Pop the hood, remove the plastic guard over the radiator and grill. Remove the 10mm bolt in the center of the grill. Remove the grill by popping the clips off each side then the grill will remove by pulling up. Remove the headlights by removing the two pins, one on top one on the inside of the lamp assembly. Remove 4, 15mm bolts from the top side of the bumper (2 upper, 2 lower that require the extension). From underneath the vehicle remove 2 more 15mm bolts (one from each side). The bolts are located just outside of the fog light assembly and sit horizontally. The bumper is now ready to be uncliped. From the inside of the wheel well use a Flathead screw driver to push in the clip while pulling the bumper away from the mounts. I used a large floor mat to keep the bumper from hitting the ground directly. It's helpful to have a second person to help on the last step.
    Good Luck!

    Aug 16, 2010 | 2004 Cadillac Escalade

    1 Answer

    Changing a headlight on a ford focus 03


    headlight bulb or assembly? remove the fender splash shield lower retaining screw. Push the fender splah shield to inside. Remove the headlamp assembly lower retaning bolt. Remove the grille. Remove the head lamp assembly

    Jun 21, 2010 | 2001 Ford Focus

    1 Answer

    2005 maxima-how to change break lights


    Removal and Installation
    1. Position trunk room trim aside.
    2. Disconnect rear combination lamp connector.
    3. Remove rear combination lamp mounting nuts.
    4. Pull rear combination lamp to remove from the vehicle.Installation is in the reverse order of removal.

      Once you have all the nuts removed you will need to pull hard on the lens. They use push clips on the outer side of the lens. As long as you apply an even amount of force you will not damage anything.

    Nov 26, 2009 | 1992 Nissan Maxima

    1 Answer

    How can i take out my head light lamp


    good luck with the headlight i replaced my wifes on her 03 altima i had to pull bumper grill off it was a pain

    Aug 20, 2009 | 2003 Nissan Altima

    Not finding what you are looking for?
    2004 Hummer H2 Logo

    Related Topics:

    73 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Hummer Experts

    yadayada
    yadayada

    Level 3 Expert

    76051 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22156 Answers

    Jeff Turcotte
    Jeff Turcotte

    Level 3 Expert

    8266 Answers

    Are you a Hummer Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...