Question about Oldsmobile Cutlass Supreme

1 Answer

How to replace front brake disk pads? - Cutlass Supreme Oldsmobile Cars & Trucks

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Need to Know a Better way to change plugs and wires myself. 3100 V6

Posted on Nov 27, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Change brake pads


For starters the front and rear us disk pads and it is not hard to do. On the front jack up the front and us jack stand for safety. After you take of the wheel remove the two bolts at the back of the brake caliper remove the caliper and then the old pads us a C- clamp with one of the old pads installed in the caliper then just us the c-clamp to push the cylinder all the way in until it will go no further install new pads put back on. But before you do the next side hit the brake to push the cylinder back out. Go to other side do the same thing. On a side not you only need to replace the rear brakes every other time you do the front. The front wear twice as fast as they do most of the stopping.

May 19, 2013 | 2004 Buick Century

1 Answer

Replace front brake discs


Remove wheels.
Remove calipers and caliper mounting brackets.
Remove brake disk.
Replace new disk, being sure to clean it thoroughly with brake cleaner and a clean rag.

Replace caliper mounting bracket.
Replace new brake pads.
Push back caliper piston.
Re-attach brake caliper.

Repeat on other side.

Remove brake fluid reservoir cap.
Pump brake pedal until hard.
**** out any excess fluid from master cylinder reservoir.
Replace cap.
Wash off any excess fluid with water and dry thoroughly.

Road-test

Be sure to keep to a slower speed than usual and keep extended braking distances until new pads and disks are bedded in.

Nov 07, 2012 | 1999 Daewoo Matiz

1 Answer

1989 toyota pickup front disk brake pads replaced, now the front calipers wont clear the new disk brake pads! Any solutions, please?


remove caliper, push disc all way home, put wheel nut on to hold home, retry fitting them the disc may be slightly scued. If no go try diffrent brand of pad I had same prob with a diffrent car last week & diffrent brand pad was 2mm thiner. If can't exchange pads get piece of emery paper on flat surface & sand away top part of pad material in round motions both ways till they fit. :-)

Jul 09, 2012 | Toyota Cars & Trucks

4 Answers

Steering wheel shakes at high speed when brakes are applied


This is caused by the front disk brake rotors being warped from heat and running out of true, the wobble of the warped rotors causes the wheel to shake when you apply the brakes, it is worse the higher the speed you apply them at. Have the front rotors machined flat again or just replace them.

Mar 16, 2011 | 1998 Toyota Camry

2 Answers

Upon acceleration there is a sqeaking noise and when i slow down it starts again very annoying.. i replaced the 2 drive belts in january.. the sound is coming from the front end maybe thr tire.. not sure..


could still be a bad belt,may need thighting, also could be the warning sensor on the front brake pads, that tells you frt brakes are low. good luck, hope this helps.

Oct 31, 2009 | 2006 Chevrolet Tahoe

1 Answer

Disk brake warning light stays on even though the disk brakes have been changed, any ideas on how to get the light to go out?


There is a brake pad sensor that should be replaced whenever you replace the brake pads. It’s located inside a whole in the brake caliper of the left front wheel. When this sensor fails, the warning light will come up in your dashboard.

Hope this helps :)

Oct 25, 2009 | 2002 BMW 5 Series

2 Answers

Vibrating


1. The wheels are not balanced. (Go for wheel balancing and alignment)

2. Check your brake system (pads etc)

Good luck.

Rate this fixya

May 29, 2009 | 1992 Lexus Es 300

2 Answers

Front brake makes grinding sound when coming to a stop.


Replace the front brake pads AND have your front brake rotors cut or replaced.

Aug 11, 2008 | 1991 Toyota Pickup

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

181 people viewed this question

Ask a Question

Usually answered in minutes!

Top Oldsmobile Experts

yadayada
yadayada

Level 3 Expert

76109 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8269 Answers

Are you an Oldsmobile Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...