Question about 2006 Nissan 1400 Bakkie

1 Answer

Hi i have a nissan 1400 bakkie.. my pipe leading into the right front calaper got snagged and cut, i replaced the pipe but cant get pressure on the front wheels.... we have bled every wheel including the "other master' at the back thing its an equalizer, we replaced the master but no pressure on the front wheels, back works fine though pedal goes half way and is rock hard "at the bottom" is there something i have missed? i need help pls.

Posted by Anonymous on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Nissan Master
  • 14,599 Answers

Any vehicle with antilock brakes needs bleeding from the caliper to the reservoir using a pressure device. Take is to a brake and tyre place.

Posted on Jun 14, 2017

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 289 Answers

SOURCE: How to replace front wheel bearings in 2006 nissan sentra

hi..check on the following link to replace the
wheel bearings.
http://autorepair.about.com/od/fixityourself/ss/wh_bearing_old.htm
check it out..
thank u..
rate me..

Posted on Mar 06, 2009

c17hydro
  • 2984 Answers

SOURCE: Directions replace front wheel bearings on a 1985 nissan stanza?

996fb79.gif

NOTE: After the wheel bearings have been removed or replaced or the front axle has been reassembled be sure to adjust wheel bearing preload. Refer to the Adjustment service procedure below. On the 1989–92 240SX there is just one wheel bearing, pressed into the hub and no adjusting cap. Refer to the exploded views of the Front Axle Hub Assembly. Review the complete service procedure.

  1. Raise and support the vehicle safely.
  2. Remove the front wheels and the brake caliper assemblies. NOTE: Brake hoses do not need to be disconnected from the brake caliper assemblies. Make sure the brake hoses are secure and do not let caliper assemblies hang unsupported from the vehicle.
  3. Work off center hub cap by using thin tool. If necessary tap around it with a soft hammer while removing.
  4. Pry off cotter pin and take out adjusting cap and wheel bearing lock nut.
  5. Remove wheel hub with disc brake rotor from spindle with bearings installed. Remove the outer bearing from the hub.
  6. Remove inner bearing and grease seal from hub using long brass drift pin or equivalent.
  7. If it is necessary to replace the bearing outer races, drive them out of the hub with a brass drift pin and mallet.
  8. Install the outer bearing race with a tool (KV401021S0 special tool number) until it seats in the hub flush. NOTE: Place a large glob of grease into the palm of one hand and push the bearing through it with a sliding motion. The grease must be forced through the side of the bearing and in between each roller. Continue until the grease begins to ooze out the other side through the gaps between the rollers. The bearing must be completely packed with grease.
  9. Pack each wheel bearing with high temperature wheel bearing grease. Pack hub and hub cap with the recommended wheel bearing grease up to shaded portions. Refer to the illustration.
  10. Install the inner bearing and grease seal in the proper position in the hub.
  11. Install the wheel hub with disc brake rotor to the spindle.
  12. Install the outer wheel bearing, lock washer, wheel bearing lock nut, adjusting cap, cotter pin (always use a new cotter pin and O-ring for installation after adjustment), spread cotter pin then install the O-ring and dust cap.
  13. Install the brake caliper assemblies and bleed brakes if necessary. Install the front wheels.

Posted on Jun 23, 2009

  • 10 Answers

SOURCE: where can i find a workshop manual for a nissan

nissan website or nissan dealer

Posted on Jul 19, 2009

yourpc
  • 190 Answers

SOURCE: I NEED A NISSAN 1400 BAKKIE FUSE BOX WIRING

I get files from www.pdftown.com I have been able to download manuals for several of my cars there. Hope this helps...

Posted on Sep 10, 2009

burdfrenzy
  • 348 Answers

SOURCE: Is it hard to replace the front wheel bearing hub

Its a big pain. The hub is rusted on tight and has to be beaten off with a mini sledge. Go to your local AP store and look it up in a repair manual to see what you are in for.

Posted on Oct 15, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to repair steering freeplay on nissan bakkie 2002 1400


Depends on where the free play is coming from. Put car front end up on stands and have helper wiggle the steering wheel while you look for where the free play is.

Feb 26, 2016 | Nissan Cars & Trucks

1 Answer

My heater on my Nissan 1400 bakkie stays on warm, moving the arm to "Off" does not help


Hi Johan, I believe the problem will be with either the operating cable or the heater control valve. Sometimes WD40 can work wonders on both, but each should be removed before being sprayed. If the cable or vave is damaged, replacement will be required. Regards John

May 23, 2014 | 2006 Nissan 1400 Bakkie

1 Answer

I drive a Nissan 1400 bakkie (not a champ) i drives good and then starts jerking and wants to die as soon i i give petrol it sounds like its smothering


hi, personally ..i love that bakkie. Ok you changed points condensor, petrol filter! please check.. When it cuts out 1. if the ignition coil is not hot, if so thats your problem.2. also on the carb... over the needle and seat there is a tiny filter... somtimes gets blocked. 3. also check when it stolls if the fuel pump is not hot or pull the outlet fuel from the pump
and crank the engine... note if fuel comes out sufficiently.

May 21, 2014 | 2006 Nissan 1400 Bakkie

1 Answer

1400 nissan bakkie brake problems, front right pipe to the calaper got cut we replaced it but got no pressure on the front wheels, back brakes work fine pressure on the pedal goes half way (rock hard at...


Some brake systems have a pressure control valve usually soon after the master cylinder that cuts off the circuit with low or no pressure in the event of a leak or rupture of the line.
Trace the metal brake lines from the master cylinder down the chassis and you may find a small cylindrical valve that has 2 inlets from the M/C and 2 outlets leading front and rear. The method of centring the piston in this valve varies from one supplier to another but basically the good rear system has pushed the piston one way and cut off the front circuit. If you lightly release the pressure in the rear system, then try and bleed the front system it may push the piston back to centre. If it does, close the rear system and then front and see if you have any front circuit pressure.
This is only a guess at your problem but remember, brakes are your life, don't be embarrassed to get help or get a manual.

May 18, 2014 | 2006 Nissan 1400 Bakkie

1 Answer

Got bakkie started revs increase but cannot maintain revs and then cuts out


You could possibly have an air leak in your intake, hense the engine cutting out at low revs. Check your piping from the air filter to the intake manifold, and also your intake sensor.
Unplug the sensor and if it does the same thing then thats your problem.

Mar 19, 2014 | 2007 Nissan 1400 Bakkie

1 Answer

1400 nissan 1 toner


check idler arms and linkage

Mar 18, 2014 | 2007 Nissan 1400 Bakkie

1 Answer

Where is the flasher relay on a nissan 1400 bakkie


this is a super old question, 3 years old, is it worth answering?

Feb 10, 2012 | Nissan 1400 Cars & Trucks

Not finding what you are looking for?
2006 Nissan 1400 Bakkie Logo

Related Topics:

22 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

75197 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

14251 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...