Question about 1999 Lexus LS 400

Open Question

How to align the camshaft timing marks on re-assembly of the heads on a lexus 1 uz-fe engine

Please advise and provide diagram on aligning the camshafts on a 1 uz-fe engine on re-assembly of cylinder heads

Posted by Anonymous on

Ad

5 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
marked
  • 6487 Answers

SOURCE: timing belt/crank shaft and camshafts

Yes, that may cause it the misalignment of the timing belt, you can try to check it and put everything back in..

Good luck.........

Posted on Aug 20, 2008

Ad

SOURCE: setting crankshaft and camshaft timing

with crank pulley white mark on 0 remove both cam pulley covers and verify yellow painted notches are exactly on the T mark cast in the fwd cam bearing housings..IF u find that it ISNT 'in time' then remove tensioner located near crank pulley and very carefully manipulate the L and R cam sprokets to allow belt to removed from cam sprockets only... DoNOT rotate engine without T belt installed .Do NOT turn engine backwards.. ever.. be advised that should the cam timing be off by more than 3 teeth either way serious engine damage will result ..this series of engines utilizes variable intake camshaft adjustment .. This job is not for the american small block specialist of yesteryear.. even an experienced asian tech is gonna have a difficult time with this lexus .. its not quite the same engine the Tundra uses...Lexus only mods befuddle reg toyota techs

Posted on Oct 29, 2008

daves944
  • 1050 Answers

SOURCE: camshaft gears

Right hand thread, just tight. You need to hold the cam itself with something solid, don't rely on the timing belt, then if you have a 3/8 impact gun, carefully rattle the bolt out. If you don't have the impact gun available, you could try getting someone to hold the cam while you put the box end of a wrench on the bolt and tap the open end. When tapping, I wouldn't use a hammer, it's too massive, use a small steel bar, like a 1/2 inch extension about ten inches long. The idea is to set up small impacts that loosen the bolt, without twisting the cam.

Posted on Mar 11, 2009

  • 146 Answers

SOURCE: Hi can you tell me how much torque spectification


  1. 60293.gif

    Cylinder head bolt tightening sequence - 1993-97

  2. Remove the head from the engine. If prying is necessary, use a protected blade; take great care not to damage the mating surfaces of the head and block.

  3. Clean the head and block of all gasket material. Take great care not to gouge or scratch the mating surfaces.

To install:

  1. Place a new gasket on the cylinder block. Make sure it is positioned correctly. Install the cylinder head in position.

  2. Lightly coat the head bolt threads and plate washers with engine oil. Install the bolts in the head.

  3. Uniformly tighten the head bolts in several passes in sequence, to 25 ft. lbs. (34 Nm).

  4. Mark the front of each bolt with a dot of paint. Following the correct order, tighten each bolt an additional 90 degrees. When complete, all the paint marks should face to the side of the engine.

  5. Again following the correct order, tighten the bolts another 90 degrees of rotation. When complete, the paint marks should face the rear of the engine, exactly 180 degrees away from the original starting point. Correct bolt torque is expressed as 25 ft. lbs. (34 Nm) + 90° + 90°.


Posted on Jan 07, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do you adjust valves on a 2006 3.5L V6 Toyota Avalon?


There is a Toyota Technical Service Bulletin issued for this:-
T-SB-0291-08 September 11, 2008 2GR-FE Valve Timing

Procedure Service Category Engine/Hybrid System Section Engine Mechanical Market USA Applicability YEAR(S) MODEL(S) ADDITIONAL INFORMATION 2005 - 2009 Avalon 2007 - 2009 Camry VDS(s): BK46K 2008 - 2009 Highlander 2006 - 2009 RAV4 Engine(s): 2GR VDS(s): BK31V, BK32V, BK33V, BK34V, ZK31V, ZK32V, ZK33V, ZK34V, ZK35V 2007 - 2009 Sienna Introduction This service bulletin provides information regarding valve timing inspection and service guidelines for vehicles equipped with 2GR-FE engines. © 2008 Toyota Motor Sales, USA Page 1 of 5 T-SB-0291-08 September 11, 2008 Page 2 of 5 2GR-FE Valve Timing Procedure Introduction (Continued) Figure 1. 3 2 1 5 9 8 7 6 4 1 RH Bank Intake Camshaft Timing Gear 2 RH Bank Exhaust Camshaft Timing Gear 3 RH Bank No. 2 Timing Chain 4 Crankshaft 5 Idler Gear 6 Timing Chain 7 LH Bank No. 2 Timing Chain 8 LH Bank Exhaust Camshaft Timing Gear 9 LH Bank Intake Camshaft Timing Gear Warranty Information OP CODE DESCRIPTION TIME OFP T1 T2 N/A Not Applicable to Warranty © 2008 Toyota Motor Sales, USA T-SB-0291-08 September 11, 2008 Page 3 of 5 2GR-FE Valve Timing Procedure Inspection 1. Set the No. 1 cylinder to TDC/compression. A. Set the timing mark to 0 on the timing chain cover by rotating the crankshaft clockwise. B. Verify the timing marks on the camshaft timing gears are in general alignment with the timing marks of the camshaft bearing cap: TIMING MARK IDENTIFICATION CYLINDER BANK INTAKE GEAR MARK EXHAUST GEAR MARK RH Bank (Bank 1) Small Mark Single Line LH Bank (Bank 2) Large Mark Double Line HINT When the engine is correctly timed, the timing marks will NOT perfectly align. Figure 2. Figure 3. RH Bank Exhaust Camshaft Timing Gear 1 2 1 Bearing Cap Timing Mark 2 Gear Timing Mark Figure 4. RH Bank Intake Camshaft Timing Gear 2 1 1 Bearing Cap Timing Mark 2 Gear Timing Mark © 2008 Toyota Motor Sales, USA T-SB-0291-08 September 11, 2008 Page 4 of 5 2GR-FE Valve Timing Procedure Inspection (Continued) Figure 5. LH Bank Intake Camshaft Timing Gear 1 2 1 Bearing Cap Timing Mark 2 Gear Timing Mark Figure 6. LH Bank Exhaust Camshaft Timing Gear 1 2 1 Bearing Cap Timing Mark 2 Gear Timing Mark HINT If the timing marks appear vastly out of alignment, turn the crankshaft one revolution (360 ) clockwise and note the position of the timing marks. Component Removal Guidelines 1. If engine disassembly is required that involves removing the camshafts or timing gears, set the #1 cylinder to TDC compression, wipe away any oil, and mark the following items in relation to each other prior to disassembly: • Timing gears • Timing chain • Timing chain No. 2 NOTE This relationship MUST be maintained. The intake gear is timed in relation to the crankshaft via the timing chain; the exhaust gear is timed in relation to the intake gear via the No. 2 timing chain. © 2008 Toyota Motor Sales, USA T-SB-0291-08 September 11, 2008 Page 5 of 5 2GR-FE Valve Timing Procedure Component Removal Guidelines (Continued) 2. If NEW camshaft timing gears or the No. 2 timing chain are being installed, the two yellow links on the No. 2 timing chain can be used to ensure correct relationship between the intake timing gear and the exhaust timing gear. Figure 7. 1 1 Yellow Link A. Align the paint mark on the timing chain with the intake gear timing mark (to ensure the intake gear is correctly timed to the crankshaft). Figure 8. RH Bank and LH Bank 3 3 4 3 3 4 5 4 5 4 1 2 1 RH Bank 2 LH Bank 3 Yellow Link 4 Gear Timing Mark 5 Timing Chain Paint Mark B. Align the two yellow links on the No. 2 timing chain to the timing marks on

May 04, 2015 | 2006 Toyota Avalon XLS

1 Answer

1996 toyota camry 2.2 5s- too manny timing marks crank shaft,cam shaft and cam shaft gears


Hi there:I dont have this diagram for 2S-ELC, 3S-FE and 5S-FE Engines, but pay attention at this...
To install:
  1. Align the cutouts of the oil pump pulley and shaft, and slide the pulley on. Retain the pulley while tightening the nut to 21 ft. lbs. (28 Nm).
  2. Align the crankshaft timing pulley set key with the key groove of the crankshaft pulley, then slide the pulley on.
  3. Install the No. 2 idler pulley with the bolt and tighten to 31 ft. lbs. (42 Nm). Be sure the pulley moves smoothly.

Remove any oil or water on the idler pulley and keep it clean.

  1. Temporarily install the No. 1 idler pulley with the retaining bolt. Hint: use a 1.65 inch (42mm) bolt in length. Do not tighten the bolt yet. Install the tension spring. Pry the pulley toward the left as far as it will go, then tighten the bolt.
  2. Turn the crankshaft until the key groove in the crankshaft timing pulley is facing upward. Install the timing belt on the crankshaft timing, oil pump, No. 2 idler and water pump pulleys.

If the old timing belt is being reinstalled, make sure the directional arrow is facing in the original direction and that the belt and crankshaft gear matchmarks are properly aligned.

  1. Install the lower (No. 1) timing belt cover and new gasket with the four bolts.
  2. Align the crankshaft pulley set key with the pulley key groove. Install the pulley. Tighten the pulley bolt to 80 ft. lbs. (108 Nm).
  3. On 2S-ELC engines, turn the crankshaft pulley and align the 0 mark on the lower (No. 1) timing belt cover.
  4. Align the camshaft knock pin with the matchmarks on the oil seal retainer.
  5. On 2S-ELC/USA engines, align the knock pin with the pin hole on the timing pulley E mark side. On 2S-ELC/Canadian engines, align the knock pin with the pin hole on the timing pulley. On 3S-FE and 5S-FE engines, align the knock pin with the groove of the pulley, and slide the pulley onto the camshaft with the plate washer and set bolt.

On 2S-ELC engines, make sure that the Matchmark on the oil seal retainer and center hole of the small hole on the camshaft timing pulley are aligned.

  1. Using the removal tool to hold the pulley stationary, install and tighten the pulley set bolt to 40 ft. lbs. (54 Nm) on the 2S-ELC and the 3S-FE. On the 5S-FE, tighten the set bolt to 27 ft. lbs. (37 Nm).
  2. On 3S-FE and 5S-FE engines, turn the crankshaft pulley and align the 0 mark on the lower (No. 1) timing belt cover.
  3. Install the timing belt and check the valve timing as follows:
    1. Align the matchmarks that you made previously, and install the timing belt onto the camshaft pulley.
    2. Loosen the No. 1 idler pulley set bolt 1 / 2 turn.
    3. Turn the crankshaft pulley two complete revolutions TDC to TDC. ALWAYS turn the crankshaft CLOCKWISE. Check that the pulleys are still in alignment with the timing marks.
    4. Tighten the No. 1 idler pulley set bolt to 31 ft. lbs. (42 Nm).
    5. Make sure there is belt tension between the crankshaft and camshaft timing pulleys.

  4. Install the upper (No. 2) timing cover with a new gasket(s). On the 5S-FE, align the two clamps for the engine wiring harness with the cover mounting bolts.
  5. Install the spark plugs.
  6. Install the right mounting insulator with bracket. Tighten the bracket bolts to 38 ft. lbs. (52 Nm), insulator nuts to 38 ft. lbs. (52 Nm) and thru-bolt to 52 ft. lbs. (71 Nm). On the 5S-FE, install the No. 2 engine mount bracket and tighten to 38 ft. lbs. (52 Nm); install the control rod and tighten the bolts to 47 ft. lbs. (64 Nm).
  7. Lower the engine.
  8. On 3S-FE and 5S-FE engines, install the alternator and alternator bracket. On 2S-ELC engines, install the power steering reservoir tank.
  9. Install the drive belt and adjust the tension.
  10. Install the cruise control actuator with bracket.
  11. Install the fender apron seal and right engine under cover.
  12. Install the right front wheel.


Hope this helps.

Jun 12, 2012 | Toyota Cars & Trucks

1 Answer

Timing belt diagram marks for toyota corolla 1996


On the 4A-FE engine do the following:
Align the camshaft knock pin with the knock pin groove on the pulley side with the K mark, the slide on the timing pulley.
Align the camshaft knock pin with the knock pin groove of the pulley, and slide on the pulley.

Align the camshaft knock pin with the groove on the pulley side with the K mark-4A-FE engine
Temporarily install the timing pulley bolt. Hold the hexagonal wrench head portion of the camshaft with a wrench, and then tighten the timing pulley bolt to 43 ft. lbs. (59 Nm).
Install the crankshaft pulley. Align the pulley set key with the groove of the pulley. Slide on the timing pulley, facing the flange side inwards.





1_10_2012_12_48_40_am.jpgGuru..saailer

Jan 09, 2012 | Toyota Corolla Cars & Trucks

1 Answer

Need diagram how to install timing chain 2004 Malibu overhead cam


Procedure is pasted below. Please let me know if you have questions.
Removal & Installation2.2L Engine
  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Drain the cooling system.
  3. Drain the engine oil.
  4. Remove or disconnect the following:
    NOTE The timing chain has 2 matching colored links and 1 uniquely colored link.
    Negative battery cable, PCV hose, Fuel line bracket, Ignition coil and module assembly Ground strap from camshaft cover, Camshaft cover, Front fender liner, Accessory drive belt Crankshaft balancer pulley, Accessory drive belt tensioner, Front cover-to-water pump bolt Remaining front cover bolts, Front cover
  5. Rotate the engine until the crankshaft sprocket mark aligns with the matching colored link (2) at the 5 o-clock position.
  6. Confirm that the INT diamond on the intake camshaft sprocket is aligned with the uniquely colored link at (1) the 2 o-clock position.
  7. Confirm that the EXH triangle on the exhaust camshaft sprocket is aligned with the matching colored link (3).
  8. Remove or disconnect the following:
    NOTE Use a 24 mm wrench to hold the camshafts to prevent them from turning.
    Timing chain tensioner, Fixed timing chain guide access plug, Fixed timing chain guide Upper timing chain guide, Exhaust camshaft sprocket, Timing chain tensioner guide Intake camshaft sprocket, Timing chain through the top of the cylinder head Crankshaft sprocket

    jturcotte_638.jpg

    Fig. Lining up the crankshaft sprocket mark with the colored link in the 5 o-clock position (2).


    jturcotte_639.jpg

    Fig. Aligning the intake camshaft sprocket mark with the colored link in the 2 o-clock position (1).


    jturcotte_640.jpg

    Fig. Aligning the exhaust camshaft sprocket (3).

To install:
  1. Install the crankshaft sprocket with the timing mark in the 5 o-clock position.
  2. Assemble the intake camshaft sprocket to the timing chain with the timing mark lined up with the uniquely colored link (1). Hand tighten a new intake camshaft sprocket bolt.
  3. Lower the timing chain through the opening in the cylinder head.
  4. Route the timing chain around the crankshaft sprocket and line up the first marching colored link (2) with the timing mark on the crankshaft sprocket.
  5. Install the exhaust camshaft sprocket with a new bolt loosely onto the exhaust camshaft.
  6. Align the timing mark on the sprocket with the last matching colored (3).
  7. If necessary, align the camshaft as follows:
    1. Using a 24 mm wrench, first turn the intake camshaft until the alignment feature on the back of the camshaft sprocket seats in the notch in the front of the intake camshaft.
    2. Turn the crankshaft 45 degrees in either direction.
    3. Turn the intake camshaft to the appropriate location.
    4. Turn the crankshaft back to top dead center (TDC).
  8. When the sprocket seats in on the camshaft, tighten the sprocket bolt hand tight.
  9. Verify all of the colored links and the appropriate timing marks are still aligned.
  10. Install the fixed timing chain guide. Tighten the bolts to 133 inch lbs. (15 Nm).
  11. Install the upper timing chain guide. Tighten the bolts to 89 inch lbs. (10 Nm).
  12. Using a 24 mm wrench to hold the camshafts, tighten the camshaft sprocket bolts 63 ft. lbs. (85 Nm) plus 30 degrees.
  13. Measure the timing chain tensioner from end to end. A new tensioner should be supplied in the fully compressed non-active state. A tensioner in the compressed state will measure 2.83 inches (72 mm) front end to end. A tensioner in the active state will measure 3.35 inches (85 mm) from end to end.
  14. If the timing chain tensioner is not in the compressed state, perform the following steps:
    1. Remove the piston assembly from the body of the timing chain tensioner by pulling it out.
    2. Install the bottom half of the Tensioner tool J-45027-2 into a vise.
    3. Install the notch end of the piston assembly into the bottom half of the tensioner tool.
    4. Using the top half of the Tensioner tool J-45027-1, turn the ratchet cylinder into the piston.
    5. Install the compressed piston assembly back into the timing chain tensioner body until it stops at the bottom of the bore. Do not compress the piston assembly against the bottom of the bore.

  15. Install the timing chain tensioner assembly. Tighten to 66 ft. lbs. (75 Nm).
  16. Release the timing chain tensioner by compressing it approximately 0.08 inches (2mm). Feed a rubber-tipped tool down through the cam drive chest to reset on the cam chain. Give the tool a sharp jolt diagonally downwards to release the tensioner.
  17. Install the timing chain oiling nozzle.
  18. Install the timing chain guide bolt access hold plug with silicone sealant on the threads. Tighten the plug to 59 ft. lbs. (90 Nm).
  19. Install or connect the following:

    Camshaft cover. Tighten the bolts to 89 inch lbs. (10 Nm). Front cover with new gasket. Tighten the bolts to 18 ft. lbs. (25 Nm). Accessory drive belt tensioner. Tighten the bolts to 33 ft. lbs. (45 Nm). Crankshaft balancer pulley using a new bolt. Tighten the bolt to 74 ft. lbs. (100 Nm) plus 75 degrees. Accessory drive belt, Front fender liner, Ground strap to camshaft cover Ignition coil and module assembly, Fuel line bracket, Air intake assembly, Negative battery cable
  20. Refill the cooling system to the correct level.
  21. Refill the engine with oil to the correct level.
  22. Start the engine and check for leaks.

    jturcotte_2381.gif

    Fig. Compressing the timing chain tensioner-2.2L engine.

Oct 06, 2011 | 2004 Chevrolet Malibu

1 Answer

I need timing marks on 2.2 toyota camry 2000


1. Remove the fan and generator V belt:
tdisline_542.jpg

tdisline_543.jpg 2. TIMING CHAIN (2az-FE Engine):
Before servicing the vehicle, refer to the Precautions Section.
Drain the engine oil.
Remove or disconnect the following:
Negative battery cable
Hood Right-side front wheel Engine under covers Right-side fender apron seal Front exhaust pipe Engine moving control rod and bracket Right-side engine mounting stay and bracket Accessory drive belt Engine appearance cover Engine wire Alternator Power steering pump, leave the hoses connected Ignition coils Ventilation hoses Cylinder head cover Turn the crankshaft pulley to set the No. 1 cylinder to TDC compression. Align the groove on the pulley with the timing mark -0- on the front cover. Remove the crankshaft pulley as follows:
1. TMC made: Use Special Tool 09213-54015 to hold the pulley to loosen the bolt. Use Special Tool 09950-50013 to remove the bolt and pulley.

2. TMMK made: Use Special Tool 09960-10010 to hold the pulley to remove the bolt. Use Special Tool 09950-40011 to remove the crankshaft pulley
tdisline_544.jpg Fig. Removing the crankshaft pulley-TMC-2.4L (2AZ-FE) engine
tdisline_545.jpg

Fig. Removing the crankshaft pulley-TMMK-2.4L (2AZ-FE) engine

Remove or disconnect the following:
Crankshaft position sensor Lower oil pan No. 1 chain tensioner Accessory drive belt tensioner

  • Support the engine with a suitable engine lifting device.
  • Remove or disconnect the following:
    Engine mounting insulators Right-side engine mounting bracket Stud bolt for the accessory drive belt tensioner from the block Front cover mounting bolts and nuts Front cover Crankshaft position sensor plate Timing chain tensioner slipper Timing chain vibration damper Timing chain Crankshaft timing sprocket
  • Turn the crankshaft counterclockwise by 90°, and align an adjusting hole of the oil pump driven sprocket with the groove of the oil pump.
    tdisline_546.jpg
  • Fig. Align the adjusting hole of the oil pump drive sprocket with the oil pump groove-2.4L (2AZ-FE) engine
    tdisline_551.jpg

    Fig. Insert a bar to lock the sprocket in position-2.4L (2AZ-FE) engine
    Put a bar in the adjusting hole of the oil pump driven sprocket to temporarily lock the sprocket in position. Remove the nut.

    Remove the bolt, chain tensioner and spring.

    Remove the chain tensioner, oil pump sprocket and No. 2 timing chain.

    To install:
    Set the crankshaft key into the left horizontal position. Turn the cutout of the drive shaft to the top

    tdisline_552.jpg

  • Fig. Align the crankshaft key and drive shaft cutout as shown for installation-2.4L (2AZ-FE) engine
    Align the yellow colored links with the timing marks of the sprocket as shown in the illustration.

  • Insert the sprockets with chain to the crankshaft and oil pump shaft.
  • Temporarily tighten the oil pump driven sprocket with the nut.
  • Insert the damper spring into the adjusting hole, and install the chain tensioner plate with the nut. Tighten to 9 ft. lbs. (12 Nm).
  • Align the adjusting hole of the oil pump driven sprocket with the groove of the oil pump.
  • Put a bar in the adjusting hole of the oil pump driven sprocket to temporarily lock the sprocket in position. Tighten the nut to 22 ft. lbs. (30 Nm).
  • Rotate the crankshaft counterclockwise by 90°, and align the crankshaft key to the top.
  • Install the timing chain vibration damper. Tighten to 80 inch lbs. (9 Nm).
  • Align the timing marks of the camshaft timing sprockets and bearing caps.
  • Using the crankshaft pulley bolt, turn the crankshaft and set the set key on the crankshaft upward.
  • Align the gold or orange colored link with the timing mark of the crankshaft timing sprocket.
  • Using Special Tool 09309-37010, tap in the sprocket.
  • Align the gold or yellow colored links with the timing marks of the camshaft timing gear and camshaft timing sprocket. Install the chain.
  • tdisline_553.jpg Fig. Align the marks of the sprockets and bearing caps to set the No. 1 cylinder at TDC-2.4L (2AZ-FE) engine
    tdisline_554.jpg Fig. Set the crankshaft set key facing upward-2.4L (2AZ-FE) engine
    tdisline_555.jpg Fig. Align the marked link of the timing chain with crankshaft sprocket timing mark-2.4L (2AZ-FE) engine
    tdisline_556.jpg Fig. Tap the crankshaft sprocket in with Special Tool 09309-37010-2.4L (2AZ-FE) engine
    tdisline_557.jpg Fig. Align the marked links of the timing chain with the camshaft sprockets during installation-2.4L (2AZ-FE) engine

    May 21, 2011 | Toyota Camry Cars & Trucks

    1 Answer

    1977 ford pinto timming marks


    Hope this helps. Please don't forget to rate....thanks!



    c17hydro_169.gif

    Crankshaft, camshaft, and distributor timing marks-2300 cc engine (© Ford Motor Co.)


    On 2000 cc engines, turn the crankshaft until the two round locating holes in the camshaft pulley are visible from the rear side of the pulley, looking forward from the left-side of the car. When these two holes are parallel to the ground, the timing pointer on the crankshaft pulley should point to TDC. If the drive belt is dislocated, the crankshaft damper will be retarded or advanced 19° per cog on the belt.

    If the engine you are working on does not have the two locating holes on the rear side of the camshaft pulley, then you will have to remove the drive belt cover and observe that when the crankshaft timing marks are aligned to TDC of the compression stroke of the No. 1 cylinder, the distributor rotor is pointing to the index mark on the upper lip of the distributor housing which coincides with No. 1 spark plug tower, and the pointer on the camshaft pulley is aligned with the index mark on the cylinder head.

    On 2300 cc engines, there is an access plug provided in the cam drive belt cover so that the camshaft timing can be checked without removing the drive belt cover. Remove the access plug, turn the crankshaft until the timing mark on the crankshaft damper indicates TDC, and observe that the timing mark on the camshaft drive sprocket is aligned with the pointer on the inner belt cover. Also, the rotor of the distributor must align with the No. 1 cylinder firing position.


    CAUTION:

    After any procedure requiring removal of the rocker arms on the 2300, each lash adjuster must be fully collapsed after assembly, then released. This must be done before the camshaft is turned.



    Crankshaft, camshaft, and distributor timing marks-2300 cc engine (© Ford Motor Co.)

    Crankshaft, camshaft, and distributor timing marks-2300 cc engine (© Ford Motor Co.)
    c17hydro_170.gif

    Checking 2000 cc overhead camshaft timing (© Ford Motor Co)

    May 08, 2011 | Ford Mustang Cars & Trucks

    1 Answer

    What are the timing marks for a 1996 toyota camry, 2.2


    2S-ELC, 3S-FE and 5S-FE Engines

    When install,
    align the crankshaft pulley set key with the pulley key groove. Install the pulley. Tighten the pulley bolt to 80 ft. lbs. (108 Nm).

    On 2S-ELC engines, turn the crankshaft pulley and align the 0 mark on the lower (No. 1) timing belt cover.
    Align the camshaft knock pin with the matchmarks on the oil seal retainer.

    On 2S-ELC/USA engines, align the knock pin with the pin hole on the timing pulley E mark side. On 2S-ELC/Canadian engines, align the knock pin with the pin hole on the timing pulley.

    On 3S-FE and 5S-FE engines, align the knock pin with the groove of the pulley, and slide the pulley onto the camshaft with the plate washer and set bolt.



    Apr 29, 2011 | 1996 Toyota Camry

    2 Answers

    2001 chev cavalier timming chain diagram


    Timing Chain and Gears REMOVAL & INSTALLATION 2.2L Engine Fig. 1: The timing marks on the sprockets should be in alignment. If not, turn the crankshaft until the marks are aligned 91113p63.jpg
    Fig. 2: The timing chain tensioner is retained by a Torx head bolt (1) and a regular hex head bolt (2) 91113p58.jpg
    Fig. 3: Unfasten the camshaft sprocket bolt 91113p59.jpg
    Fig. 4: Remove the camshaft sprocket and the timing chain at the same time . . . 91113p60.jpg
    Fig. 5: . . . then remove the tensioner assembly 91113p61.jpg
    Fig. 6: Compress the tensioner spring and insert a cotter pin or nail in the hole provided to hold the tensioner in position 91113p62.jpg
    1. Disconnect the negative battery cable.
    2. Remove the front cover as previously detailed.
    3. Place the No. 1 piston at TDC of the compression stroke so that the marks on the camshaft and crankshaft sprockets are in alignment (see illustration).
    4. Loosen the timing chain tensioner nut as far as possible without actually removing it.
    5. Remove the camshaft sprocket bolts and remove the sprocket and chain together. If the sprocket does not slide from the camshaft easily, a light blow with a soft mallet at the lower edge of the sprocket will dislodge it.
    6. Using a suitable gear puller, remove the crankshaft sprocket. To install:
    7. Press the crankshaft sprocket back onto the crankshaft.
    8. Install the timing chain over the camshaft sprocket and then around the crankshaft sprocket. Make sure that the marks on the two sprockets are in alignment (see illustration). Lubricate the thrust surface with Molykote® or its equivalent.
    9. Align the dowel in the camshaft with the dowel hole in the sprocket and then install the sprocket onto the camshaft. Use the mounting bolts to draw the sprocket onto the camshaft and then tighten to 66-68 ft. lbs. (91-95 Nm).
    10. Lubricate the timing chain with clean engine oil. Tighten the chain tensioner.
    11. Installation of the remaining components is in the reverse order of removal. Fig. 7: Exploded view of the timing chain and sprockets - 2.2L OHV engine 87953107.gif

    Nov 11, 2010 | Chevrolet Cavalier Cars & Trucks

    1 Answer

    Where should timing gears aline on a 1998 pontiac sunfire need pictuure


    Timing Chain and Gears REMOVAL & INSTALLATION 2.2L Engine Fig. 1: The timing marks on the sprockets should be in alignment. If not, turn the crankshaft until the marks are aligned 91113p63.jpg
    Fig. 2: The timing chain tensioner is retained by a Torx head bolt (1) and a regular hex head bolt (2) 91113p58.jpg
    Fig. 3: Unfasten the camshaft sprocket bolt 91113p59.jpg
    Fig. 4: Remove the camshaft sprocket and the timing chain at the same time . . . 91113p60.jpg
    Fig. 5: . . . then remove the tensioner assembly 91113p61.jpg
    Fig. 6: Compress the tensioner spring and insert a cotter pin or nail in the hole provided to hold the tensioner in position 91113p62.jpg
    1. Fig. 7: Exploded view of the timing chain and sprockets - 2.2L OHV engine 87953107.gif
    2.3L and 2.4L Engines .
    1. Fig. 8: The chain must be in the "timed'' position - 2.3L and 2.4L engines 87953108.gif
      Fig. 9: Remove the timing chain guides 87953109.gif

    2. .
    3. Fig. 10: Timing chain assembly retaining bolts - 2.3L and 2.4L engines 87953111.gif

    4. .
      1. Fig. 11: Reloading the tensioner to its "ZERO'' position, then install to the chain housing 87953110.gif

    prev.gif next.gif

    Oct 08, 2010 | 1998 Pontiac Sunfire

    1 Answer

    Timing for tropper 6cly and 4 camshafts and 24 valves model 2000


    Timing Belt
    Removal
    1. Disconnect battery ground cable.
    2. Remove air cleaner assembly.
    3. Remove radiator upper fan shroud from radiator.
    4. Move drive belt tensioner to loose side using wrench
    then remove drive belt.
    850RW001
    Legend
    (1) Crankshaft Pulley
    (2) Cooling Fan Pulley
    (3) Tensioner
    (4) Generator
    (5) Air Conditioner Compressor
    (6) Power Steering Oil Pump
    (7) Drive Belt
    5. Remove cooling fan assembly four nuts, then the
    cooling fan assembly.
    6. Remove cooling fan drive pulley assembly.
    7. Remove idle pulley assembly.
    8. Remove serpentine belt tensioner assembly.
    9. Remove power steering pump assembly.
    10.Remove crankshaft pulley assembly using
    5–8840–0133–0 crankshaft holder, hold crankshaft
    pulley remove center bolt, then the pulley.
    11. Remove right side timing belt cover then left side
    timing belt cover.
    12. Remove lower timing belt cover
    13. Remove pusher.
    CAUTION: The pusher prevents air from entering
    the oil chamber. Its rod must always be facing
    upward.
    014RW011
    Legend
    (1) Up Side
    (2) Down Side
    (3) Direction For Installation
    (4) Locking Pin
    14. Remove timing belt.
    CAUTION:
    1. Do not bend or twist the belt, otherwise its core
    could be damaged. The belt should not be bent at
    a radius less than 30 mm.
    2. Do not allow oil or other chemical substances to
    come in contact with the belt. They will shorten
    the life.
    3. Do not attempt to pry or stretch the belt with a
    screw driver or any other tool during installation.
    4. Store timing belt in a cool and dark place. Never
    expose the belt direct sunlight or heat.
    6A–30 ENGINE MECHANICAL
    Installation
    NOTE: For correct belt installation, the letter on the belt
    must be able to be read as viewed from the front of the
    vehicle.
    014RY00042
    Legend
    (1) Crankshaft Timing Pulley
    (2) RH Bank Camshaft Drive Gear Pulley
    (3) Water Pump Pulley
    (4) Idle Pulley
    (5) LH Bank Camshaft Drive Gear Pulley
    (6) Tension Pulley
    014RY00043
    Legend
    (7) Alignment Mark on Oil Pump.
    (8) Alignment Mark on Timing Belt
    (9) Alignment Mark (notch) on Crankshaft Timing
    Pulley.
    (10) Alignment Mark (groove) on Crankshaft Timing
    Pulley.
    014RW006
    Legend
    (1) Timing Belt
    (2) Engine Rotation Direction
    (3) Cylinder Head Side
    1. Install timing belt.
    1. Align the mark (notch) of crankshaft timing pulley
    (2) with mark on oil pump (1).
    Align the mark (groove) on the crankshaft timing
    pulley (3) with alignment mark (white dots line) on
    the timing belt (4).
    NOTE: When timing marks are aligned, No.2 piston will
    be on Top Dead Center.
    014RW003
    Legend
    (1) Alignment Mark on Oil Pump
    (2) Groove on Crankshaft Timing Pulley
    (3) Alignment Mark on Crankshaft Timing Pulley
    (4) Alignment Mark on Timing Belt
    ENGINE MECHANICAL 6A–31
    2. Align the alignment mark on the RH bank
    camshaft drive gear pulley (2) to the alignment
    mark of the cylinder head cover RH (3).
    3. Align the alignment mark (white line) on the timing
    belt (1) with alignment mark on the RH bank
    camshaft drive gear pulley (2) (on the left side as
    viewed from the front of the vehicle) and put the
    timing belt on the camshaft drive gear pulley.
    Secure the belt with a double clip or equivalent
    clip.
    014RW00004
    Legend
    (1) Alignment Mark on Timing Belt (White line).
    (2) Alignment Mark on Camshaft Drive Gear
    Pulley.
    (3) Alignemnt Mark on Cylinder Head Cover RH.
    4. Align the alignment mark on the LH bank
    camshaft drive gear pulley (2) to the alignment
    mark of the cylinder head cover LH (3).
    5. Align the alignment mark (white line) on the timing
    belt (1) with the alignment mark on the LH bank
    camshaft drive gear pulley (2).
    When aligning the timing marks, use a wrench to
    turn the camshaft drive gear pulley, then set the
    timing mark between timing belt and camshaft
    drive gear pulley and put the timing belt on the
    camshaft drive gear pulley.
    Secure the belt with a double clip or equivalent
    clip.
    NOTE: It is recommended for easy installation that the
    belt be secured with a double clip or equivalent clip after
    it is installed the timing belt to each pulley.
    014RW00005
    Legend
    (1) Alignment Mark on Timing Belt (White line).
    (2) Alignment Mark on Camshaft Drive Gear
    Pulley.
    (3) Alignemnt Mark on Cylinder Head Cover LH.
    6. Install crankshaft pulley temporarily and tighten
    center bolt by hand (do not use a wrench).
    Turn the crankshaft pulley clockwise to give some
    belt slack between the crankshaft timing pulley
    and the RH bank camshaft drive gear pulley.
    2. Install pusher and tighten bolt to the specified torque.
    Torque : 25 N·m (2.5 Kg·m/18 lb ft)
    1. Install the pusher while pushing the tension pulley
    to the belt.
    2. Pull out pin from the pusher.
    NOTE: When reusing the pusher, press the pusher with
    approximately 100Kg to retract the rod, and insert a pin
    (1.4 mm piano wire).
    014RW011

    Mar 18, 2009 | 2000 Isuzu Trooper

    Not finding what you are looking for?
    1999 Lexus LS 400 Logo

    Related Topics:

    27 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Lexus Experts

    yadayada
    yadayada

    Level 3 Expert

    76630 Answers

    ROBERT GARCIA
    ROBERT GARCIA

    Level 3 Expert

    905 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22219 Answers

    Are you a Lexus Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...