Question about 2007 Nissan Micra 1.4

Open Question

Nissan micra 2007 removal rear door panel

Remove rear door panel

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 250 Answers

SOURCE: How to remove drivers door panel on a 2007 Nissan Tiida hatchback

The door handle has a c clip behinde it that you can not see.Goto a auto parts store and thay will have a cheep tool to help you.(you need a special tool for this. The WINDOW CRANK handle has a 'c-clip' behind it. The door opening handle trim is held in by either a screw behind a plastic flap that will pop out(behind the lever)or it is held in at four points by plastic tabs (two on top and two on the bottom)that can be undone carefully with a screwdriver or the like. When this plastic trim is removed the door panel should come off.
Be aware that there are plastic clips (back side of the panel) on the perimeter of the panel that hold it in as well.
the tweeter panel just pops out look on the bottom of the door for screws and around the door handle and you will have to pop your window and door lock controls out and the reflector on the door pops out and there is two screws there then al you have is the clips behind the door they make tools for it but a flat tip screwdriver will be fine just get the tip close to the clip and pull it out .
1. Remove window crank (it has a kind of 'bent wire' c-clamp, which holds it onto the window crank shaft). 

2. Pry upwards the top plastic cover to the arm rest (this is a plastic coated foam rubber piece, on which you rest your arm). 

3. Remover the two now visible screws which fasten the arm rest onto the door. 

4. Remove the one screw fastening the inside door handle. 

5. With a blunt tool, gently hit the inside door handle in a forward direction (towards the door hinge). This will release the door handle from the door. 

6. Pry between the door panel and the door, to unsnap the snaps holding the door panel in place. 

7. Finally, lift door panel out and up to remove it from door. 

Posted on Feb 09, 2009

  • 42 Answers

SOURCE: 1991 Nissan Maxima: Removal of front driver side door panel

This is out of my haynes manual
1 disconnect negative battery cable
2 on manual window equipped modesl remove the window crank using a hooked tool to remove the retainer clip.
3 on power window equipped models pry out the armrest switch control plate and disconnect the electrical connections
4 detach the armrest pull handle retaining screw then remove the inside door handle trim bezel
5 insert a wide putty knife, a thin screwdriver or a special trim panel removal tool between the trim panel and the head of the retaining clip to disengage the door panel retaining clips.then remove the remaining door panel retaining screws at the lower edge of the door panel.
6 once all of the clips are screws are disengage detach the trim panel disconnect any electrical connectors and remoe the trim panel from the vehicle by gently pulling it up and out.
7 for access to the inner door remove the door panel support bracket then peel back the watershield taking care not to tear it. it install the trim panel first press the watershield back into place. if necessary add more sealant to hold it in place.
8 installation is the reverse of removal

Posted on Mar 20, 2009

  • 383 Answers

SOURCE: how do you remove a door panel, 2002 nissan sentra

Frank, YA ready?????? The first thing is a kind of trim ring which snaps around the parameter of the inner door handle. You need a small flat faced screw driver and get a piece of cardboard which you can slip between the screw driver and the panel where ever you might pry against so you don't cut it or mark it.
Take the cardboard place it against the door panel right at the top of where the inner door handle trim ring is and out near the end at the top, push the screw driver under the ring , twist it a little and the ring will pop loose. Do the same on the bottom and the back of the ring hooks the the handle.
Next, on the end of the armrest, you can put the screw driver between the upper and lower sections at the back and lift up on the upper section. (it clips into the lower section. ) Once you have lifted it, the front section of it just hooks, so pull it backwards and you can remove it.
Next, look down into the little pocket you put your hand in when you pull the door shut. Most of the doors had a small plastic cap which you pry up and below that cap is a screw which you remove with a # 6 phillips screw driver (that is the most common size phillips used) Once the screw is out, move to the front of the arm rest and pry it up like you did the back one. It is designed the same way.
This part will have the switch(s) in it. The connector has a latch lever near the center of the connector where it plugs into the switch. Push the lever down while rocking the connector side to side a little while you pull on it. The connector should easily come out.
There are two screws which fasten the door panel to the door around the area where the arm rests were, They too are phillips head screws. On rare occasions you might find these two fasteners with bolts that have heads which a 10mm wrench or socket will fit.
The last place is the bottom. On the bottom out toward the ends are plastic clips which snap into the door shell it self and are affixed to the door panel. Pry lightly between the panel and the door shell and the panel should pop loose.
Once it is loose, you lift the panel up and off the door, do not swing it out away from the door.
If the door has lights at the bottom, unplug the light before removing the door panel, it will be obvious how it comes loose.
Good luck.
All the doors come apart about the same way.

Posted on May 04, 2009

  • 1986 Answers

SOURCE: 54 Micra door panel removal

You'll need to remove screws that are by the door handle, arm rest, under door and side of door and then gently pull back on the panel as there will also be retaining clips attached and you don't want to break them. If needed, you can pull back the weather seal (can't reuse it, but it's not that important) and you will be able to access everything inside the door. It sounds like the linkage connecting the handle to the latch is not working (broken or slipped off)

Posted on Aug 14, 2009

abauto
  • 353 Answers

SOURCE: need step by step instructions on how to remove a

Rear Bumper: Service and Repair
REAR BUMPER
Removal and Installation
REMOVAL
1. Remove the LH and RH rear combination lamps.
2. Remove both the rear wheels and tires.
3. Remove the LH and RH splash shields.
4. Remove the rear bumper fascia clips and screws, then remove the rear bumper fascia.
5. Remove the rear energy absorbing foam.
6. Remove the rear bumper reinforcement.
7. Remove the rear bumper supports.
INSTALLATION
Installation is in the reverse order of removal.

c674cde.jpg

Posted on Nov 12, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do you remove the rear door panels on a 2007 Nissan Altima.


Good day Peter.

You can find some pointers here
Inside Rear Door Panel Removal or here
How to remove door panels Nissan Forums Nissan Forum
To the Nissan Forum materials, I can add that auto parts stores and eBay are both good places to get kits of tools for popping auto panels. They make it easier to get them off without gouging up the paint or the panel with a screwdriver, and with less breakage of the pins.

Good Luck!
D

Nov 23, 2015 | 2007 Nissan Altima 2.5

2 Answers

How do I change rear wheel bearing on 2009 k12 nissan micra


That should be in the service manual: You can search for one using Google and this in the search box: "2009 k12 nissan micra service manual" without the quotes, it should show a lot of different sources for one.

Nov 28, 2014 | Nissan Cars & Trucks

1 Answer

I need to replace a rear door handle on a nissan maxima 2007


you will have to remove the door panel.. once you do so peel back the plastic film behind the door panel then look in the door with a flash light most likely will be a 2- 10mm bolts a

Mar 27, 2011 | 2007 Nissan Maxima 3.5 Sl Sedan

2 Answers

Blower heater unit in micra k12


hi did you get the resistor fixed if not you need to remove the glove box by removing the screws that can be seen then there are two plastic lugs that need to be pulled out sideways to enable you to remove the glove box then you will see the resistor card on the side of the motor thats on the new shape micra k12

Mar 03, 2010 | 2006 Nissan Z

1 Answer

54 Micra door panel removal


You'll need to remove screws that are by the door handle, arm rest, under door and side of door and then gently pull back on the panel as there will also be retaining clips attached and you don't want to break them. If needed, you can pull back the weather seal (can't reuse it, but it's not that important) and you will be able to access everything inside the door. It sounds like the linkage connecting the handle to the latch is not working (broken or slipped off)

Jun 09, 2009 | 2003 Nissan Se R

1 Answer

Noisy central locking Nissan MIcra


Hi there, this is a very common fault, you need to replace the drivers door actuator to stop the noise, ive done loads of these. hope this helps.

Feb 24, 2009 | 2007 Nissan Armada LE

Not finding what you are looking for?
2007 Nissan Micra 1.4 Logo

Related Topics:

65 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

75077 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

705 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...