Question about 2000 Honda Passport

1 Answer

How do you reset the gas pedal - 2000 Honda Passport

Posted by on


1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that got 5 achievements.


    An expert whose answer got voted for 20 times.


    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 64 Answers

If you are "resetting" the gas pedal because you replaced it..... you will need to return to the Honda dealer to have your computer "flashed" . The pedal MUST be replaced with a new unit, you cannot use "salvaged" parts for the gas pedal. It will not work.

Posted on May 19, 2014


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

07 Ford freestyle replaced ETB position sensor and both converters wrench light and check engine comes on after about 10 miles car goes into lymp mode no more than 20mph sometimes turning off resets

If this is "fly by wire" throttle, it must be synced with gas pedal. Gas pedal units are so prone to failure Lokar makes a replacement pedal assembly far superior to stock unit.

Jul 14, 2015 | Ford Cars & Trucks

1 Answer

I need to reset service light

You should be able to reset the service light by turning the key to the "run" position (do not start vehicle) and then immediately push down on the gas pedal to the floor 3 consecutive times and then start the vehicle... this should reset the service reminder light. when you push the gas pedal 3 times it must be done consecutively within about 15 - 20 seconds. Hope this helps...

Oct 22, 2012 | 2008 Chrysler Pt Cruiser

3 Answers

How to remove "oil change" code on 04 gmc sierra

Turn the key on,and press the gas pedal three times slow,within five seconds

Jun 08, 2010 | 2004 GMC Sierra

1 Answer

My change oil light will not reset , I have tried depressing the gas pedal and I also have tried the reset button what else can I try

this car should be the pump the gas pedal reset procedure - i will explain it just in case you are unfamilier. turn key to on postion (do not start). wait for change oil light to illuminate. fully depress the gas pedal to the floor 3 times in less then 5 seconds. wait another ten seconds, then start the car. the light should be out. good luck!

May 01, 2010 | 2003 Pontiac Grand Am

1 Answer

Reset change oil message?

hold gas pedal to the floor. turn key to run positon but do not turn over engine. Quickly pump gas pedal 4-5 times and hold to floor. Oil light will flash. Turn off and remove key. Repeat if needed

Btw, I’m available to help over the phone in case u need at

Jan 12, 2010 | 2004 Chevrolet Colorado

1 Answer

How do i reset the change oil light in 2003 pontiac grand am

turn your ignition switch to on,push the gas pedal down to the floor completely three times in 5 seconds and let the gas pedal up after 10 seconds you will see the light blink it is now reset

Nov 14, 2009 | 2003 Pontiac Grand Am

4 Answers

Oil light stays on

You need to put the key on and push the gas pedal to the floor three times within five second to reset the oil life light.Some g.m.'s have a reset buttom in the fuse panel that needs to be pushed first and some don't.Check the owners manual under change oil for your specific year car.

Oct 21, 2009 | 2003 Chevrolet Impala

1 Answer

I had the oil changed in my 2005 ford 500 and the oil change light won't reset back to the mileage info.

If you have the hand book that should show you how to reset it.Who ever changed your oil should have reset that for you.On some fords you hold your foot on the gas pedal with the ignition switched on.Keeping it pressed turn of the ignition,And then turn back on with the gas pedal still pressed to the boards.Then leave of gas after 10 seconds,

Jul 19, 2009 | 2005 Ford Taurus

2 Answers

I need to reset my oil change.

Turn on the key and within 5 seconds press the gas pedall 3 times to the floor and then watch the change oil soon light blink a few times and it is reset for another term of driving.

Jun 28, 2009 | 2003 Buick Century

10 Answers

Oil light

Hi lady d tilli,

Take off the fuse cover on the drivers side of the dash. there should be a bunch of fuses. in the middle is a red button that says "reset." turn your key to the on position, but DO NOT START. press the reset button until the change oil light blinks, then turn the key back off it should be fine after that. for the 05's theres somthing you have to do with the gas pedal. i think you do the same, by turning the key on but not starting...and then tapping the gas pedal 3 times.

Hope this helps a bit,
Good luck,

Jun 09, 2008 | 2004 Pontiac Grand Am

Not finding what you are looking for?
2000 Honda Passport Logo

Related Topics:

89 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts


Level 3 Expert

80339 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides