Question about 2006 Land Rover Range Rover Sport
My range rover sport 2005 2.7 diesel will not start have been told I need a new fuel pump
Posted by Anonymous on
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
Unfortunately I believe that will require a trip to the dealer, and a hefty price tag to go with it. Most dealers refuse to let anyone else handle their security systems. And most keys have the alarm keypad built in making it even more dealer specific. I wish I could give better news.
Posted on Mar 27, 2009
you need 2 remove your radio and open you shloud change the ic for frequency to work it is very easy to change it if youneed ana help contact me
Posted on Sep 28, 2009
Check all electrical conections. If they are good then it is probably the switch itself.
Posted on Mar 17, 2010
Testimonial: "I'll take a look at the switch. All connections seem fine."
There are few possibilities that are to be checked.:----
Engine cranks normally, but it does not fire: If you know that you have spark and fuel, the next step is to check for compression. For this, you will need a mechanic's grade compression tester that will screw into a spark plug hole. You will need to remove the spark plugs and use the compression tester to test the compression on each cylinder. If the compression is very low on all cylinders, that is a sure sign that the timing belt (or timing chain depending on the engine) has failed and will have to be replaced. ------------- This troubleshooting will let you know the problem.Thanks.
You turn the key to start and hear the starter motor crank the engine, but when you release the key, the cranking stops and there is silence. This means that the battery and starting motor are working properly, but the engine is not firing. If you continue cranking the engine over in this way, the battery will eventually run down and will need to be recharged, but the battery and starter are not the cause of your problem.
There are a number of causes for this type of no-start condition, the most common being that you are simply out of gas. Assuming that you have fuel in the tank, you will need to go through a series of tests to determine what is causing the problem. The testing procedure is as follows:--- Spark:---------An easy way to test for spark is with an inexpensive spark tester. This is a device that is readily available at most auto supply stores. You use it by simply holding it next to a spark plug wire. If you see the neon lamp flashing while someone cranks the engine, then you have spark and should move on to checking for fuel. If there is no spark, or a very weak spark, you will have to replace the spark plug or the coil pack.It has to be checked. Fuel:
First step here is to listen for the fuel pump running inside the gas tank. When you turn the key to run, you should easily hear the pump come on, run for a few seconds to build fuel pressure, then turn off. If you do not hear it, it could mean that the fuel pump or circuitry is bad. (Fuel pump failure is a common problem). Fuel injected cars are very sensitive to proper fuel pressure. If the pressure is off, even by a few pounds, it will cause noticeable performance problems, or a no-start condition. To check for proper fuel pressure, you will need a fuel pressure gauge that is suitable for your type of system.Or you can also get the fuel pressure tested at local car garage,If fuel pressure is low then its a fuel pump and fuel filter related problem. Compression:
If you know that you have spark and fuel, the next step is to check for compression. For this, you will need a mechanic's grade compression tester that will screw into a spark plug hole. You will need to remove the spark plugs and use the compression tester to test the compression on each cylinder. If the compression is very low on all cylinders, that is a sure sign that the timing belt (or timing chain depending on the engine) has failed and will have to be replaced.
This troubleshooting will let you know the problem.Thanks.
Posted on Dec 08, 2010
Testimonial: "Thank you very much for such a quick and detailed response. I will try your suggestions and see how I get on. Thanks again."
Tips for a great answer:
Jun 20, 2014 | 2000 Land Rover Range Rover
Apr 18, 2014 | 1997 Land Rover Range Rover
Dec 10, 2012 | 2004 Land Rover Range Rover
Jun 29, 2010 | 1995 Land Rover Range Rover
Apr 28, 2010 | 2000 Land Rover Range Rover
Apr 09, 2010 | 2005 Land Rover Freelander
Feb 07, 2010 | 2006 Land Rover Range Rover Sport
Jun 06, 2009 | 1997 Land Rover Range Rover
Mar 27, 2009 | 2006 Land Rover Range Rover Sport
Mar 10, 2009 | 2000 Land Rover Range Rover
15 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: