Question about 2004 Dodge Stratus

Open Question

I took my dodge stratus 2004 to the dealer to get the remote for my alarm system programmed but they said it did not work and I do not know why

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 46 Answers

SOURCE: Programming keyless remote for Neon 2004

There is a way to program a remote if there is already a valid remote. Unfortunatly if you don't have a valid remote the only way to get one programmed is at the dealership with their scan tool.

I have pasted directions for programming a remote if there is already a valid transmiter.


CUSTOMER PROGRAMMING For a customer to be able to program RKE transmitters themselves, at least one RKE transmitter must be programmed already. This procedure is to add additional transmitters. If all transmitters are lost, the DRB III® scan tool must be used to program the new transmitters.

  1. Insert the key into the ignition switch, and turn the ignition switch to the RUN position without starting the vehicle (allow chimes to stop).
  2. Using the RKE transmitter programmed to the RKE module, press and continuously hold down the UNLOCK button for 4-10 seconds.
  3. Within the 4-10 second time range, continue to hold the UNLOCK button and press the PANIC button. Both buttons may then be released. Upon the PANIC button being depressed, the message for customer programming mode will be transmitted to the RKE module.
  4. A chime will be heard to verify that the customer programming mode has been entered (allow 3 seconds to hear chimes).
  5. Press and release any button on each transmitter that is to be programmed to the RKE module, including any transmitters which were previously programmed to the RKE module (with a maximum of four possible). After each transmitter is successfully programmed, a chime will be heard to verify that successful programming of the transmitter has occurred.
  6. After thirty seconds, or upon the ignition switch being turned OFF, the RKE module will exit programming mode.

Posted on Aug 30, 2008

emissionwiz
  • 75235 Answers

SOURCE: 2004 Dodge Stratus 2.7 thermostat location

Finding the thermostat: Follow the LOWER radiator hose to where it meets the engine. It's in there. Most cars that I've worked on have the thermostat at the end of the upper radiator hose, but not this car. Replacing the thermostat: You need to remove the thermostat housing. (It's the piece that the lower radiator hose connects to.) - You do not need to remove the radiator hose from the housing. - First remove the bolt that is holding a bracket. This bracket just holds some wires in place. - Now remove the three bolts that hold the housing to the engine block. These bolts can be fairly hard to turn, but just keep trying. - Gently pry the housing away from the engine block. You can use a flat-head screwdriver to help pry, but do not scratch the mating surfaces of the housing and the block. - Pull out the thermostat, noting that the spring end goes into the engine. - When you put the new thermostat in, you probably want to use a new black rubber gasket, but you might be able to use the old one if you have no choice. Also, I didn't add any permatex or anything and it seems fine. - I tightened the bolts to 22foot pounds, but this might be a little high. Whatever you do, DO NOT overtighten the bolts. Couple other notes: I first removed the air cleaner cover and tubes to get a little more working room. I also unplugged one wiring harness to make more room. Otherwise, I was able to get my big hands in there. A new thermostat did not fix my problem. Here is a description of the problem I was having and the solution: Problem: The temperature gauge was spiking occasionally, all the way into the red. It would spike up and come back to normal. It would spike usually while in idle, but sometimes while driving. Usually about once every twenty minutes. Things I checked first: - The plastic reservior for the radiator was full to the top. - The electric fans were running, and running on high speed. - The car had working heat. - Replaced the thermostat. Did nothing to help the problem. Problem Found: - Vapor lock. Even though the reservior was full of fluid, it had previously gotten too low and the system sucked in some air. Once that happens, it doesn't matter if the reservior is full, the cooling system will not draw in the coolant. This is because filling the plastic reservior does not pour coolant directly into the cooling system. The coolant is sucked into the cooling system through a tube, like drinking soda through a straw. So the reservior, where they tell you to add coolant, was full but the cooling system (radiator, engine, pump, etc.) was almost out of coolant and wasn't able to draw in any more. Solution: When the engine is cool, open the metal radiator cap that's sticking right up out of the engine. It can be found by following the upper radiator hose to the engine. There is a tall metal tube with a metal cap on it. Pull that cap off (when it not hot) and fill it up with radiator fluid. (I use radiator fluid that's pre-diluted and designed for all makes and models of cars). Idle the car, in park, for about thirty seconds. Stop the engine and put the cap back on. If you're lucky, all the air bubbles are out of the system and you're all set.

Posted on Dec 02, 2008

  • 1861 Answers

SOURCE: MAF Sensor 2004 Dodge Stratus

If your car has a MAF (Mass Air Flow) sensor, it would be located in the air delivery tube that runs from the air filter box to the throttle plate assembly on the intake manifold. It will have a wiring connector going to it, also. The MAF does exactly what it is called: It "senses" the volume, or "mass" of the air-flow; thusly it needs to be in the intake air tube. If you do NOT have such a device in the air-tube, you have a MAP sensor, (Manifold Absolute Pressure); this is another way of measuring the same air volume, albeit older technology. You will commonly find this device on the firewall, with a vacuum line running to the intake manifold.

I hope that this sheds some light on your question.

Thanks for choosing FixYa for advice!

Posted on Mar 06, 2009

  • 10 Answers

SOURCE: 2004 ram remote keyless entry

The instructions are in the owner manual on how to manually program it.

Posted on Jul 07, 2009

  • 19 Answers

SOURCE: replace water pump on 2004 Dodge Stratus 2.4L DOHC

First, I'd recommend you buy a manual, because the water pump is internally mounted, driven by the timing belt. You will also need a puller to remove the crankshaft pulley. You can usually rent/borrow this from the same place you bought the manual. The manual will also show you how to properly install the timing belt and compress the tensioner.
You will need to drain the cooling system, raise the car (safely), remove the right tire, right inner fender, right engine mount (aka front mount), accessory drive belts, timing belt cover, timing belt and tensioner (which needs to be recompressed correctly), and now you are at the water pump. Since the timing belt has to be removed, you should also replace it.

Posted on Sep 19, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do i rest my dodge stratues rt 2004 alarm


The remote entry unit will disable the alarm

Mar 03, 2015 | 2004 Dodge Stratus

1 Answer

My car battery went dead, bought a new one, every time I hook up positive cable, car alarm goes off........


remove alarm reinstall after fitting. at least cut power supply and back up supply fit battery repair reinstall alarm.

Feb 16, 2015 | 2004 Dodge Stratus

1 Answer

On my 2004 dodge stratus the door lock switch on the drivers side does not unlock the doors. It will lock all of the doors and the windows but it just will not unlock. The passenger side still works for...


I have answered this subject many times: it is a bad BCM or Body Control Module. The problem begins intermittently, but progresses during two to three years and finally inutilizes all door locks. As BCM repair and removal from the dash is a real pain, I resorted to disconnect the wiring to the BCM and paid a much lower price to a Car Alarm installer to put an inexpensive alarm that comes with its own remote. In that way I use the new remote to lock-unlock and the original one to set the original alarm-inmobilizer. Amclaussen.

Aug 02, 2013 | 2004 Dodge Stratus

1 Answer

2004 Stratus alarm problems, when opening door


On most cars you can disarm the system by locking AND unlocking the drivers door with the key. Check your owners manual if you have one.

Jul 25, 2012 | 2004 Dodge Stratus

1 Answer

How do i permanently disengage the alarm system on a 1998 dodge stratus?


If it is an aftermarket or dealer installed alarm, and not integral to the cars computers. You can have it removed by any shop that installs alarms.

Mar 12, 2011 | 1999 Dodge Stratus

1 Answer

1997 dodge stratus agency alarm came on now car seems to be blocked it turns on but then turns off and the alarm keeps honking when i turn the ing switch to on position the lights,door locks,stereo and...


You need to get the alarm system reprogrammed. I don't know your personal code. It may be in the owner manual. If not, you will need to call a Dodge dealer.

Feb 15, 2011 | 1997 Dodge Stratus

1 Answer

How can i re-program my 2003 dodge stratus alarm?


take it to the dealer as they have prepriatary software

Jan 08, 2010 | 2003 Dodge Stratus

1 Answer

Trying to install an astra 600 car alarm into a 04 dodge stratus


I called dodge local service dealer and ask the chief mech. He said the lock unlock switch had two resistors, Lock was 7200 ohms and the unlock had a 620 ohm both going to the PCU (computer) with an reduced 12 voltage supply to the CPU the CPU looks at the amount of reduced and will energize the lock or unlock Solenoid. added the resisters to each solenoid lock 7200 ohm and unlock 620 ohm on the ASTRA 600 alarm output to the CPU. works OK.
Thanks for your Interest in my problem.

Tony Spar

Nov 04, 2009 | 2004 Dodge Stratus

1 Answer

1997 Dodge Stratus won't turn over.


Call the dealership and see what they say.

Mar 03, 2009 | 1997 Dodge Stratus

Not finding what you are looking for?
2004 Dodge Stratus Logo

Related Topics:

16 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

75197 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7782 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...