Question about 2005 Chevrolet Malibu Maxx

Open Question

How to replace license plate light bulb chevy malibu maxx

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

SOURCE: Replace Dash light bulbs on 2004 Malibu Maxx

you need to take the hole dash out and on the back of the speed dash there are little bulbs take them out then replace them

Posted on Dec 30, 2008

Ad
  • 1 Answer

SOURCE: how to replace headlight bulbs 1999 chevy malibu

Thanks Pierre!

Merci beaucoup!

Everything worked as mentionned. Be carefull with the plastic in the winter. Make sure to use a flat screw driver and get it close to the slider and not on the edge. I cracked one of the tongues. Those L shaped slots are under the plastic cover with the two big plastic plugs that you also remove with the flat screw driver

Pierre Godin, Boissevain Manitoba.

Posted on Feb 10, 2009

  • 1027 Answers

SOURCE: license plate light replacement

The license plate lights are in the ledge above the license plate. 2 screws keep the lens cover in place. Remove the screws, and the cover comes off. Just pull the lamp out (wedge base) and replace.

Posted on Apr 18, 2009

  • 1 Answer

SOURCE: replacing license plate lights on Chevy Trailblazer

I just had the same problem. I took the cover off, saw the white bulb base, twisted it to take it out, but it popped back inside the door. I got it out, but it wouldn't pull through, so I twisted it back in place and went to Autozone to get new bulb. Once I saw the new bulb, it was obvious, just the bulb itself pulls out. There's so little room to work, I couldn't get it with just my fingers - - maybe rubber gloves would have worked, but I used pliers, lightly, wiggled it a little and it popped right out. I had a similar issue once with the taillight bulb and had to break the bulb and then grip the remaining filament wires with pliers to get it out, so that was my backup plan, just in case.

Hope this helps others.

Posted on Apr 19, 2009

  • 12 Answers

SOURCE: I have a 2005 Chevy Malibu Maxx. It has a TC

i think it stands for traction control. most cars with that say ETC which stands for electronic traction control. if you have a manual for the car it should say what it is.

Posted on Sep 27, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Plate light does not work, but lights are good and sockets seem good


check bulb the number plate light runs on the same circuit as the side lights so if they are working its got to be a bad earth on the plate light

Jan 24, 2016 | Cars & Trucks

1 Answer

2004 malibu. i have replaced license plate bulbs but they are still not working. can someone please tell me where their fuse is?


Sorry to say the license plate lights get power from the same circuit the parking lights do. So if the parking lights work, the license plate lights should have power too.

Jul 29, 2014 | 2004 Chevrolet Malibu

1 Answer

Where are the turn signal flashers located in a 2004 Chevy Malibu Maxx LT ?


check the bulbs when you get rapid flash normally 1 pf the bulbs are out

Jul 06, 2013 | 2004 Chevrolet Chevrolet Malibu MAXX LT

1 Answer

How do I change the light bulb above the rear license plate?


YOU HAVE TO OPEN THE TRUNK LID REMOVE THE BLACK PLASTIC COVER FOR THE TRUNK LID LATCH.REMOVE THE LICENSE PLATE LIGHT HOUSING FROM THE TRUNK LID.REMOVE THE BULB SOCKET FROM THE LICENSE PLATE LIGHT HOUSING.TO REMOVE BULB FROM THE SOCKET SIMPLY PULL IT STRAIGHT OUT OF THE SOCKET.

May 15, 2010 | 2008 Chevrolet Malibu

1 Answer

Changing headlight bulbs on a chevy malibu maxx


ther should be two white clips on top of ur head light need to pull them up then pull out head lght

Mar 31, 2010 | 2005 Chevrolet Malibu Maxx

2 Answers

How do you replace the third brake light bulb?


If you do not know what you are doing you should go to a mechanic. A simple slip with a screw driver can cost a lot of money.

Aug 24, 2017 | 2004 Chevrolet Malibu Maxx

1 Answer

Put in new bulb but still no flashing for right turn signal in 2005 chevy malibu. Bulb lights up but does not flash.


ck the rear bulbs as well - tail lamps on this year are known to fill up with water and rust out the sockets

Oct 18, 2009 | 2005 Chevrolet Malibu Maxx

2 Answers

2004 malibu maxx third brake light


It is an LED lamp and the entire terminal needs to be replaced. I would suggest checking the fuse first, being that the replacement can run over $60

Aug 08, 2009 | 2007 Chevrolet Malibu Maxx LTZ Hatchback

1 Answer

Replace Dash light bulbs on 2004 Malibu Maxx


you need to take the hole dash out and on the back of the speed dash there are little bulbs take them out then replace them

Dec 30, 2008 | 2005 Chevrolet Malibu

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

308 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

77544 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22306 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...