Question about 2000 Dodge Caravan

1 Answer

Can power steering pump be removed by taking out right drive axle and removing through wheel well. 2000 Dodge Caravan 3.0 litre

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Governor:

    An expert whose answer got voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 98 Answers

Dropping the strut should be sufficient......

Posted on Jun 23, 2009

  • aroostookb
    aroostookb Jun 23, 2009

    Dropping the strut should be sufficient......

×

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My power steering was fine then suddenly it started to go stiff and then a slight whine when turning the wheel. refilled the power steering fluid, it took a whole 1 litre jug and was fine for a few...


It should like you may have a leak if it took a whole litre. Once you fix the leak you may also find the power steering pump still makes noise. This can be repaired by replacing the pump. I hope this helps.

Aug 29, 2011 | 2000 Dodge Caravan

1 Answer

How to replace a powersterling pulley on 1999 dodge grand caravan


The procedure to remove the power steering pulley out of the 1999 dodge caravan engine is as follows:----

· First disconnect the black, negative cable from the battery.

· Then Take off the windshield wiper module.

· Raise the front of the vehicle using a jack.

· Then from underneath the vehicle remove the drive belt splash shield .

· Locate the power steering pump bracket and--working from underneath the car--loosen the through bolt; then remove the pressure hose routing bracket.

· Place a catch pan on the floor, underneath the power steering pump fluid reservoir, and siphon as much steering fluid from the tank; then remove the pressure and fluid supply hoses from the pump.

· Take off the rear pump mounting bolt and front mounting bolts through the pulley. Make sure to grab and keep the spacer located between the pump and mounting bracket once you remove the bolts.

· Take the pump and pulley assembly over the aluminum bracket and out of the engine.

Reinstall all parts and new pulley in reverse.

Thanks. keep updated for any more query.you can rate this solution and show your appreciation.

Sep 22, 2010 | 1999 Dodge Caravan

1 Answer

How to remove transmission from a 2001 dodge caravan


front wheel drive, your gonna have to remove the wheels and front drive axles and then unbolt the trans from the motor. if its rear wheel drive you just remove the driveshaft, then the trans and your done

Jul 31, 2010 | 2001 Dodge Caravan

1 Answer

2000 dodge caravan remove mounting assembly to release power steering pump. I have already removed the passenger wheel and wheel well took all the bolts from the pump and all i could find from the...


I have changed the pump out on my wife's 99 Voyager, 3.3 liter. Per my manual (and experence) there should be a nut at the back of the pump connecting it to the bracket. Then there are three (3) bolts which connect the pump to the bracket (front of pump under pulley. I my memory serves part of the front bracket will have to be removed with the pump. Lastly, if a 3.3 or 3.8 V6 you;ll have to remove the exhaust where it connects to the back manifold (has a flex pipe to it. Trust me on this the manual is correct with removing the ehaust from the engine, I tried to prove the engineers wrong but its the only way out and back in. Plan for these four (4) bolts to break and replace with new when putting pump back in, use new exhaust gasket too. To remove/install pulley to pump you'll need a special puller, cheap to by or may be rented.

I hope this may have assited you,
Tom

Jun 08, 2010 | 2000 Dodge Caravan

1 Answer

How long does it take to fix front bearings on a 97 dodge caravan? and cost


About an hour a side...This is the whole job and pictures....

The hub and wheel bearing unit is serviced as a complete assembly. Replacement of the front drive hub and bearing assembly can be done without having to remove the steering knuckle from the vehicle. However, if the hub/bearing assembly is frozen to the steering knuckle, removal of the steering knuckle is required.
  1. Disconnect the negative battery cable.
  2. Remove the cotter pin from the end of the stub axle. Remove the nut lock and spring washer. With the brakes applied, loosen, but do NOT remove the axle nut and washer with the vehicle still on the ground or damage to the wheel bearing will result.
  3. Raise and safely support the vehicle. Remove the wheel.
  4. Remove the front brake caliper assembly from the steering knuckle assembly and support from the strut assembly using a strong piece of wire.
    1. Remove the front brake rotor from the hub/bearing assembly.
    2. Remove the retaining nut and washer from the halfshaft stub axle.
    3. Remove the ABS wheel speed sensor from the steering knuckle.
    4. Remove the 4 hub and bearing assembly mounting bolts from behind the steering knuckle.
    5. Remove the hub and bearing assembly from the steering knuckle.
  5. To install:
    1. Thoroughly clean the mating surfaces of the steering knuckle and the hub and bearing assembly of any foreign material or nicks so the surfaces are clean and smooth.
    2. Install the new hub and bearing assembly and tighten the mounting bolts in a crisscross pattern to 45 ft. lbs. (65 Nm). Be sure the hub and bearing assembly is seated squarely against the front steering knuckle.
    3. Install the disc brake rotor.
    4. Install the brake caliper assembly onto the steering knuckle.
    5. Install the axle washer and nut. Tighten but do not torque.
    6. Install the ABS wheel speed sensor.
    7. Install the wheel and lug nuts. Torque the lug nuts, in sequence, to 95 ft. lbs. (129 Nm).
    8. Lower the vehicle. Do NOT roll the vehicle until the axle nut has been properly torqued or damage to the front wheel bearings will result.
    9. With the vehicle's brakes applied, torque the axle nut to 180 ft. lbs. (244 Nm). Install the spring washer, nut lock and a new cotter pin. Wrap the cotter pin prongs tightly around the axle nut lock.
    10. Reconnect the negative battery cable. Check the wheel alignment.

fe8edd6.gif
The hub/bearing assembly is attached to the steering knuckle with four bolts


9733319.gif
Removing a hub/bearing assembly



1867b08.gif
If the hub/bearing is "frozen" to the steering knuckle, separate the ball joint and lightly tap on the hub/bearing from behind



09233ac.gif
The hub/bearing assembly should free itself from the steering knuckle

About $60 a hub.

May 23, 2010 | 1997 Dodge Caravan

2 Answers

How do you bleed a power steering pump on a 2005 dodge caravan


With the engine running slowly turn the steering wheel from stop to stop several times. Make sure the level stays full. As the air pockets are reduced the level may go down. It may take awhile to get all the air out of the system. If the power steering works it is not a problem.

Feb 25, 2010 | 1999 Dodge Ram 2500 4WD

1 Answer

2000 Dodge Caravan tranmission started making a clicking sound only in 1st gear. Otherwise drives fine. What could be wrong?


you need to have the CV axle shafts checked,the clicking sound is the first sign of a bad one,you need to turn the steering wheel one way sharp wile accelerating,then the other way,so you can determine if left axle or right.

Jan 15, 2010 | 2001 Dodge Grand Caravan

1 Answer

Need to remove power steering pump


1. Take off the battery black-cable (negative cable).
2. Drain out the power-steering reservior.
3. Place a large container under the car to catch excess fluid. Disconnect the power-steering hoses.
4. Remove the right front wheel, and support the car on jack-stands.
5. Remove the apron fender under the right front-wheel
6. Disconnect and loosen the clamp and the fluid return hose from the pump.
7. Remove the pressure line-to-pump union bolt. Push this away from the pump. Remove the sealing washers on both sides of the fitting.
8. Remove the pivot bolts and the drive-belt.
9. Remove the adjuster, mounting bolts, pivot and take-out the pump.
10. Installation is opposite of removal.

Nov 14, 2009 | 1992 Toyota Camry V6

1 Answer

How do i remove the Powersteering pump in my 1998


Replace the ps pump, brake fluid is not a lubricant, your pump is scored, raise the van, block it, remove the sheild, belt and right axle, and remove the pump, you will have to flush the system with 4-5 litres of PS fliud only. GOOD LUCK, RDJRP

Oct 02, 2009 | 1998 Dodge Grand Caravan

1 Answer

Power steering pump removel


if you remove right side drive axle,it should come thru bottom

Apr 26, 2009 | 1996 Dodge Caravan

Not finding what you are looking for?
2000 Dodge Caravan Logo

Related Topics:

213 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6924 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...