Question about 1993 Jeep Grand Cherokee

1 Answer

Parking brake lever

How to change the e brake lever

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 159 Answers

Lift lever remove screws for cover you'll see a nut at the end of brake cable.remove it remove bracket bolts and pull lever out. Put new lever over cable start the nut back on Cable bolt back in position tighten cable nut.start vehicle pull brake try to go forward then reverse if it moves tighten cable til you can't roll.reinstall outer cover.

Posted on May 18, 2014

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Chevy Aveo5 2008 automatic trans - how do I remove the parking brake lever?


Chevrolet Aveo Would not Shift out of Park - Sensor Glitch

sensorglitch.livejournal.com/91859.html
Nov 17, 2009 - Tags, ', aveo, brake light, chevrolet, chevy, gear, park, parking, shift, ]... believe it or not all I had to do was replace the brake switch (a cheap $5 part). ... Theautomatic transaxle shift lever may not shift out of the park position ...
Service Manual2007 Aveo PARKING BRAKEwww.autocats.ws/manual/chevrolet/tis0911/.../Aveo/.../9T2_4G0.EN.htm...Remove the complete parking brake lever assembly and the cable from the assemblyby unfastening the parking brake lever-to-vehicle underbody bolts and ...Missing: 2008How to disconnect the parking brake cable on a Chevy ...? 2:05https://www.youtube.com/watch?v=FxAQMbcHAnQApr 22, 2013 - Uploaded by Josh BruniVehicle Tips: How to disconnect the parking brake cable on aChevy .... How to replace rear brakes and rotors on a 2008 Buick Lucerne ...

Jan 05, 2016 | Cars & Trucks

1 Answer

How to replace shift indicator light 2009 focus


pull your emergency brake up, Detach the park brake lever boot from the park brake lever,
Lift upward on the rear of the floor console finish panel to release the
floor console finish panel clips ,disconnect the electrical connector, Slide the park brake lever boot and the floor console finish panel over the park
brake lever, there you will be able to remove bulb by twisting socket,

Nov 05, 2013 | Ford Focus Cars & Trucks

1 Answer

Emergency brake cable, how do I remove it from caliper?


Press the parking brake lever with slip-joint pliers to relieve the tension on the brake cable. Grip the cable's end with locking pliers and disconnect it from the parking brake lever

Jun 07, 2012 | 1997 Mercury Sable

1 Answer

How to installing brake shoes on back ?


First you have to compress the parking brake cable spring and attach the parking brake lever.
Clean and lubricate the brake backing plate.
Use silicon Brake Caliper Grease and Dielectric Compound.
Then,
install the rear brake shoes and linings:
1) position the rear brake shoes and linings
2) position the parking brake lever
3) install the brake shoe hold-down spring pins and the brake shoe hold-down springs.

Install the parking brake strut
1. install the parkig brake link spring on the parking brake strut
2. install the parking brake strut
3. Install the brake shoe anchor ping guide plate.

Install the short brake shoe retracting spring
1. Place the brake shoe adjusting lever cable over the anchor pin, with crimped side in
2. Install the short brake shoe retracting spring

Note: Make sure the brake shoe adjusting lever cable is positioned in the cable guide groove

Install the long brake shoe retracting
1. install the cable guide
2. position the brake shoe adjusting lever cable in the cable guide groove
3. install the long brake shoe retracting spring

Note: to prevent incorrect installation, teh socket of each brake adjuster screw is stamped R or L

Assemble the brake adjuster screw assembly.
1. apply silicone brake caliper grease and dielectric compound
2. install the brake adjuster screw into the brake show adjusting screw nut to the end of the threads and then loosen one half turn
3. install the brake shoe adjusting screw socket on the brake shoe adjusting screw nut.

Install the brake adjuster screw assembly
1. Position the brake adjuster screw assembly
2. Install the brake shoe adjusting screw spring
3. Position the brake shoe adjusting lever cable
4. Position the adjusting lever return spring and the brake shoe adjusting lever
5. Hook the brake shoe adjusting lever cable to the brake shoe adjusting lever.

Test the operation of the automatic self-adjuster
1. Pull the brake shoe adjusting lever cable and check that the brake shoe adjusting lever rotates the brake shoe adjuster assembly
2. Release the brake shoe adjusting lever cable and check that the brake shoe adjusting lever advances to the next notch on the brake shoe adjusting screw nut.

Adjust the brakes.

Install the brake drum.

Thats it

Sep 10, 2010 | 1998 Ford Ranger SuperCab

2 Answers

1997 Ford contour rear brake shoe replacment help.


Brake shoe removel:

Depress and turn the retainers for the hold-down springs and pins to remove them from each shoe. Slide the brake shoe assembly--including the shoes and springs--down so you can disengage the top ends of the shoes from the cylinder and tilt them to lift them past the retaining plate.

Unhook the lower retracting spring from the front brake shoe to disconnect it. Spread the shoes apart at the bottom to remove the adjusting screw, the screw's retracting spring and the adjuster lever. Remove the front brake shoe.

Pull the parking brake cable spring back with diagonal cutting pliers, grip the cable with the pliers without cutting it, unhook the cable from the parking brake lever and remove the rear brake shoe with the lever.

Disconnect the parking brake lever from the rear shoe by spreading the retaining clip with a screwdriver and removing the clip and its spring washer.
  • Step 4 Pull the parking brake cable spring back with diagonal cutting pliers, grip the cable with the pliers without cutting it, unhook the cable from the parking brake lever and remove the rear brake shoe with the lever.
  • Step 5 Disconnect the parking brake lever from the rear shoe by spreading the retaining clip with a screwdriver and removing the clip and its spring washer.

  • Read more: How to Change Rear Brakes on a 1997 Ford Taurus | eHow.com http://www.ehow.com/how_6123373_change-brakes-1997-ford-taurus.html#ixzz0u2xgUqun
  • Step 3 Unhook the lower retracting spring from the front brake shoe to disconnect it. Spread the shoes apart at the bottom to remove the adjusting screw, the screw's retracting spring and the adjuster lever. Remove the front brake shoe.
  • Step 4 Pull the parking brake cable spring back with diagonal cutting pliers, grip the cable with the pliers without cutting it, unhook the cable from the parking brake lever and remove the rear brake shoe with the lever.

  • Read more: How to Change Rear Brakes on a 1997 Ford Taurus | eHow.com http://www.ehow.com/how_6123373_change-brakes-1997-ford-taurus.html#ixzz0u2xdByQ8

  • Step 2 Slide the brake shoe assembly--including the shoes and springs--down so you can disengage the top ends of the shoes from the cylinder and tilt them to lift them past the retaining plate.
  • Step 3 Unhook the lower retracting spring from the front brake shoe to disconnect it. Spread the shoes apart at the bottom to remove the adjusting screw, the screw's retracting spring and the adjuster lever. Remove the front brake shoe.
  • Step 4 Pull the parking brake cable spring back with diagonal cutting pliers, grip the cable with the pliers without cutting it, unhook the cable from the parking brake lever and remove the rear brake shoe with the lever.
  • Step 5 Disconnect the parking brake lever from the rear shoe by spreading the retaining clip with a screwdriver and removing the clip and its spring washer.

  • Read more: How to Change Rear Brakes on a 1997 Ford Taurus | eHow.com http://www.ehow.com/how_6123373_change-brakes-1997-ford-taurus.html#ixzz0u2xVyUAt

  • Step 2 Slide the brake shoe assembly--including the shoes and springs--down so you can disengage the top ends of the shoes from the cylinder and tilt them to lift them past the retaining plate.
  • Step 3 Unhook the lower retracting spring from the front brake shoe to disconnect it. Spread the shoes apart at the bottom to remove the adjusting screw, the screw's retracting spring and the adjuster lever. Remove the front brake shoe.
  • Step 4 Pull the parking brake cable spring back with diagonal cutting pliers, grip the cable with the pliers without cutting it, unhook the cable from the parking brake lever and remove the rear brake shoe with the lever.
  • Step 5 Disconnect the parking brake lever from the rear shoe by spreading the retaining clip with a screwdriver and removing the clip and its spring washer.

  • Read more: How to Change Rear Brakes on a 1997 Ford Taurus | eHow.com http://www.ehow.com/how_6123373_change-brakes-1997-ford-taurus.html#ixzz0u2xVyUAt

    Jul 17, 2010 | 1995 Ford Contour

    1 Answer

    Change drum brakes


    Brake Shoe: Service and Repair
    REMOVAL
    1. Raise vehicle and remove rear wheels.
    2. Remove and discard spring nuts securing drums to wheel studs.
    3. Remove brake drums.
    NOTE: If drums prove difficult to remove, retract brake shoes. Remove access plug at the rear of backing plate and back off adjuster screw with
    brake tool and screwdriver.
    4. Remove U-clip and washer securing adjuster cable to parking brake lever.
    5. Remove primary and secondary return springs from anchor pin with brake spring pliers.
    6. Remove hold-down springs, retainers and pins with standard retaining spring tool.
    7. Install spring clamps on wheel cylinders to hold pistons in place.
    8. Remove adjuster lever, adjuster screw and spring.
    9. Remove adjuster cable and cable guide.
    10. Remove brake shoes and parking brake strut.
    11. Disconnect cable from parking brake lever and remove lever.
    INSTALLATION
    1. Clean support plate with brake cleaner.
    2. If new drums are being installed, remove protective coating with carburetor cleaner or brake cleaner.
    3. Clean and lubricate anchor pin with light coat of Mopar multi-mileage grease.
    4. Apply multi-purpose grease to brake shoe contact surfaces of support plate.
    5. Lubricate adjuster screw threads and pivot with spray lube.
    6. Attach parking brake lever to secondary brake shoe. Use new washer and U-clip to secure lever.
    7. Remove wheel cylinder clamps.
    8. Attach parking brake cable to lever.
    9. Install brake shoes on support plate. Secure shoes with new hold-down springs, pins and retainers.
    10. Install parking brake strut and spring.
    11. Install guide plate and adjuster cable on anchor pin.
    12. Install primary and secondary return springs.
    13. Install adjuster cable guide on secondary shoe.
    14. Lubricate and assemble adjuster screw.
    15. Install adjuster screw, spring and lever and connect to adjuster cable.
    16. Adjust shoes to drum.
    17. Install wheel/tire assemblies and lower vehicle.
    18. Verify firm brake pedal before moving vehicle.

    56a4433.jpg

    Aug 12, 2009 | 1997 Jeep Cherokee Country

    1 Answer

    PARKING BRAKE LEVER- NO TENSION / DISC BRAKE ADJUSTMENT-OFF


    If you remove the cover of the E-brake there should be a tention ajustment that you can do yourself.

    May 19, 2009 | 2003 Hyundai Santa Fe

    1 Answer

    1999 nissan quest rear brake shoes need changing


    help is here:
    http://autos.groups.yahoo.com/group/villagerquest/

    Drum Removal
    1. Remove the rear wheel and the tire assembly. Refer to Section 204-04 .
    1. Retract the brake shoes and loosen the brake adjuster screw.
    975565f.gif
    1. Remove the brake drum.
    ----------------------
    May require big hammer to loosen drum from axle flange. Hit between the the lugs, not on them.

    ------------------------------------------------------------------------------
    #10 is access plug to back off adjusting wheel.

    f9f31b5.gif
    Item Part Number Description 1 2261 Rear wheel cylinder 2 — Dust boot (part of 2128) 3 2197 Wheel cylinder piston (part of 2261) 4 — Cup (part of 2128) 5 2204 Wheel cylinder piston cup spring (part of 2128) 6 — Wheel cylinder housing (part of 2261) 7 — Brake shoe hold-down pin 8 — Access hole (part of 2212) 9 — Rear brake bleeder screw (part of 2261) 10 — Access hole plug 11 — Rear wheel cylinder bolt 12 2212 Rear brake backing plate 13 — Rear brake backing plate bolts 14 2N790 Parking brake lever clip 15 — Spring washer 16 — Secondary brake shoe and lining (part of 2200) 17 — Brake shoe hold-down spring (part of 2B514) 18 — Lower retracting spring (part of 2B514) 19 2A637 Parking brake lever 20 — Parking brake lever pin 21 2A177 Brake shoe adjusting lever 22 — Adjuster lever pin (part of 2A177) 23 — Primary brake shoe and lining (part of 2200) 24 — Upper retracting spring (part of 2B514) 25 2041 Brake adjuster screw

    --------------
    Shoes Removal

    Take a picture and remember how each part goes and attaches
    1. Remove the brake drum, refer to Drum in this section.
    1. Remove the upper retracting spring.
    1. Remove the lower retracting spring.
    1. Remove the self-adjuster.
    38bcaa0.gif
    1. Remove the hold-down springs.
    1. Remove the parking brake lever clip and the parking brake lever.

    Apr 17, 2009 | 1999 Nissan Quest

    1 Answer

    I need a schematic for the rear brakes on an F150 super cab with 4.6L automatic trans 4wheel drive


    Drum, Rear Brake System Standard Rear Brake
    9969082.gif
    Item Part Number Description 1 2069 Brake Shoe Hold-Down Spring Pin 2 — Rear Wheel Cylinder Retaining Bolt (2 Req'd) 3 — Washer (2 Req'd) 4 — Anchor Pin (Part of 2211) 5 — Wheel Cylinder 6 2028 Brake Shoe Anchor Pin Guide Plate 7 2A637 Parking Brake Lever 8 2296 Brake Shoe Retracting Spring (Short) 9 2296 Brake Shoe Retracting Spring (Long) 10 2200 Rear Brake Shoe and Lining (Secondary) 11 — Washer 12 2106 Parking Brake Lever Pin Retainer 13 — Brake Shoe Adjusting Lever Cable Guide 14 2A642 Primary Brake Shoe Parking Brake Lever Link 15 2A601 Parking Brake Link Spring 16 2068 Brake Shoe Hold-Down Spring 17 2A176 Brake Shoe Adjusting Lever 18 2048 Brake Shoe Adjusting Screw Socket 19 2047 Brake Shoe Adjusting Screw Nut 20 2041 Brake Adjusting Screw 21 2049 Brake Shoe Adjusting Screw Spring 22 2200 Rear Brake Shoe and Lining (Primary) 23 2A178 Brake Shoe Adjusting Lever Cable 24 2211 Brake Backing Plate
    Heavy Duty Rear Brake
    6dcb5d2.gif
    Item Part Number Description 1 — Rear Wheel Cylinder Retaining Bolt 2 00538 Lock Nut 3 2212 Rear Brake Backing Plate 4 2262 Rear Wheel Cylinder 5 2A642 Primary Brake Shoe Parking Brake Lever Link 6 2A601 Parking Brake Link Spring 7 2A637 Parking Brake Lever 8 2106 Parking Brake Lever Pin Retainer 9 — Parking Brake Lever Bolt 10 — Secondary Shoe Assembly 11 2A179 Brake Shoe Adjusting Lever Cable Guide 12 2068 Brake Shoe Hold-Down Spring 13 — Adjusting Lever Pin 14 — Adjusting Lever Return Spring 15 2A176 Brake Shoe Adjusting Lever 16 2047 Brake Shoe Adjusting Screw Nut 17 2049 Brake Shoe Adjusting Screw Spring 18 2041 Brake Adjuster Screw 19 — Primary Shoe Assembly 20 2068 Brake Shoe Hold-Down Spring 21 2200 Rear Brake Shoe and Lining 22 2035 Brake Shoe Retracting Spring 23 2A178 Brake Shoe Adjusting Lever Cable 24 2092 Brake Adjusting Hole Cover 25 2069 Brake Shoe Hold-Down Spring Pin
    The rear drum brakes:
    • Have internal shoes that expand against the brake drum (1126).
    • Are a single-anchor type.
    • Are actuated by one rear wheel cylinder (2262).
    • Have two pistons in the rear wheel cylinder (2261). One exerts force against the upper end of the primary shoe; the other exerts force against the upper end of the secondary shoe.
    • Adjust rear brake shoes and linings (2200) automatically.
    • Need manual brake adjustment if the adjusters are not operating properly or after the rear brake shoes and linings have been replaced.
    When the brake pedal is applied, hydraulic fluid pressure forces the pistons in the rear wheel cylinder outward, moving the rear brake shoes and linings against the brake drum.
    The rear drum brake system includes the parking brake mechanism. Refer to Section 206-05 .

    Apr 04, 2009 | 1997 Ford F150 Regular Cab

    1 Answer

    Loose emergency brake on 2004 Saturn Vue


    1. Apply and fully release the park brake several times. Verify that the park brake lever releases completely.
    2. Turn ON the ignition. Verify the red BRAKE warning lamp is not illuminated.
    3. If the red BRAKE warning lamp is illuminated, verify the following:
      • The park brake lever is in the fully released position and against the stop.
      • There is no slack in the park brake cable.
    1. Turn OFF the ignition.
    2. Disable the SIR system.
    3. Remove the front floor console.
    4. With the park brake lever in the released position, using ONLY hand tools, loosen the adjusting nut completely to the end of the front cable threaded rod.
    5. Raise and support the vehicle.
    6. Remove the rear tire and wheel assemblies.
    7. Adjust the rear drum brakes.
    8. Ensure there is no brake shoe drag after adjustment by rotating the brake drums. If drag exists, re-center the brake shoes and perform the brake shoe adjustment again.
    9. Install 2 wheel nuts to the wheel studs and firmly hand tighten in order to retain the brake drums.
    10. Lower the vehicle to permit access to the park brake lever.
    11. Raise the park brake lever 1 detent position. Notice: Refer to Fastener Notice in Service Precautions.

    Jan 14, 2009 | 2004 Saturn VUE

    Not finding what you are looking for?
    1993 Jeep Grand Cherokee Logo

    84 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Jeep Experts

    yadayada
    yadayada

    Level 3 Expert

    75822 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22156 Answers

    Kevin Daniels

    Level 3 Expert

    1455 Answers

    Are you a Jeep Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...