Question about 2008 Skoda Octavia 1.9

1 Answer

Where is the pressure control sensor 2001 ford windstar SEL?

Also how do you tell if it is bad and where do you purchase one? Tried Auto Zone and O Rielly's.

Posted by on

  • 1 more comment 
  • Coss May 17, 2014

    Hi Jean Pennington, I want to help you with your problem, but I need more information from you. Can you please add details in the comment box? Pressure control sensor for what? Fuel? oil, climate controls or?

  • Jean Pennington
    Jean Pennington May 18, 2014

    The electronic pressure control sensor for the tranny in a 2001 ford windstar. I was driving on the 680 at about 70 and it dropped onto 2nd and the od light on the dash started flashing the rpms went up to 5 and I had to tow it home. It came back with 12 OBD2 codes and the first one was P1747, P0743 etc.

  • Jean Pennington
    Jean Pennington May 18, 2014

    It will drive in reverse and go into first and second. After warming up it trys to stall though and will not go into third or overdrive.

×

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Genius:

    An expert who has answered 1,000 questions.

  • Master
  • 1,056 Answers

From what I have read about those 2 error codes you are probably best off taking it to a transmission shop.
You'll find information about the P0743 code here http://www.obd-codes.com/p0743 P0743 is a generic error code for all Ford trucks. The P1747 is specifically for the EPC Solenoid Short Circuit
Electronic Pressure Control (EPC) Solenoid, which is inside the transmission. You have to drain the fluid and open the bottom cover pan. Replace the EPC and the filter at minimum; once you have it open you'll be able to find out more.
Good luck with this, it's not going to be a simple fix.

Posted on May 18, 2014

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2001 windstar sel motor runs but has a miss in


It sounds like you have a bad spark plug. Take it to autozone and have them hook up an OBD II scanner to it for you. Its free of charge.

May 17, 2010 | 2001 Ford Windstar

1 Answer

Replace windshield washer resevoir on a 2000 ford windstar


YOU CAN GO TO AUTO ZONE OR ADVANCE AUTO PARTS .BUY A HAYNES MANUAL FOR 2000 FORD WINDSTAR.IT WILL SHOW AND TELL YOU HOW TO FIX WINDSHIELD WASHER RESERVOIR.

Nov 11, 2009 | 2000 Ford Windstar

2 Answers

Check engine light blinks


Ok, i would ave the ignition coil pack tested for its operational valve asap if possible. this is either an ignition coil pack issue or, a bad ECM. the ECM controls the ignition timing in this vehicle so, the problem will be there if the crank shaft sensor and cam sensors are ok.

I would pull the trouble codes asap as well. this will help diagnosis this issue correctly. this can be done at a local auto zone or a local mechanics shop as well.

Jun 19, 2009 | 2001 Ford Windstar

1 Answer

My check transmission light is on and my o/d light is flashing. I have a 2001 ford windstar sel with 155000 miles


Go to autozone for a free computer scan and get the fault codes first.

I think it may be a defective vehicle speed sensor (VSS) but the codes will tell us.

Jun 14, 2009 | 2001 Ford Windstar

1 Answer

Change oxygen sensor 2001 ford windstar


fist unclip wire,then unscrew it with a 28mm spanner ,fitting procedure is the reverse .It turns anticlockwise to unscrew and clockwise to screw up ,torque setting is a grunt and two scuffed knuckles and max of 3 swear words

Jan 01, 2009 | 2001 Ford Windstar

1 Answer

Need to replace number 1 sensor


Hi, it is very easy to change but have go repair shop, first when u get sensor, they have to heat the sensor with gas light that use in welding, the neck right from where it tied the manifold and put small engine oil, then start losing it, and dont forget to remove the battery terminal when doing the work,when it lose then disconect the wire that is connected to the point where it is connected and fix the new one by tieting it firmly to the position and fix back the wire and battery head and start the car u will see that the check engine light is gone

reagards

elmiskin3

Dec 31, 2008 | 2001 Ford Windstar

1 Answer

Check engine light on


bad fuel pressure regulator, stuck egr valve, throttle position sensor bad, take it to a auto zone and have them scan the codes for you.

Dec 08, 2008 | 2003 Ford Windstar

2 Answers

Alternator ,battery or fuse


Probably the battery. Take it off the car and take it to Auto Zone and they will test it for free.

Jun 18, 2008 | 2001 Ford Windstar

Not finding what you are looking for?
2008 Skoda Octavia 1.9 Logo

149 people viewed this question

Ask a Question

Usually answered in minutes!

Top Skoda Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Brad Brown

Level 3 Expert

15950 Answers

Frank Magliocca

Level 3 Expert

1114 Answers

Are you a Skoda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...