Question about 2005 Volkswagen Touareg

Open Question

Volkswagen touareg how to change a rear third brake light or head mounted brake lamp?

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
garyq1970
  • 85 Answers

SOURCE: rear brake pad installation 99 volkswagen Passat

If you can't see diagrams(sometimes happens) let me know and I will get them to you

  1. Raise and support the vehicle. Remove the rear wheels.
  2. If equipped, disconnect the brake pad wear sensor from the harness.
  3. Counterhold the lower sliding pin using a thin open-end wrench and remove the caliper-to-sliding pin hex bolt.
  4. Pivot the caliper upward or if necessary remove the upper caliper-to-sliding pin hex bolt.
  5. Using a brake caliper retraction tool, select the appropriate sized piston press arbor and install the tool onto the brake caliper. Following the tool manufacturer's recommendations, use the tool to rotate the caliper piston clockwise as it is pressed into the brake caliper housing, until it is fully retracted.
0900c152800c30b8.jpgUse a thin open-end wrench to . . . 0900c152800c30b7.jpg. . . support the caliper sliding pin when removing the caliper mounting bolt 0900c152800c30d7.jpgUse a disc brake caliper piston retracting tool that will rotate the caliper piston as it is pressed into the caliper 0900c152800c30d8.jpgThe rear caliper piston is slotted to allow a retracting tool to rotate the piston when replacing the brake padsTo install:
  1. Clean the brake caliper and all sliding surfaces. With the caliper piston pressed fully back into the caliper housing, check for leaking fluid and damaged dust boots.
  2. If equipped, install a new brake pad wear sensor in the pad if the plastic part has been worn through on the old sensor. New sensors are not required unless the wire inside the plastic part has been exposed.
  3. Lubricate the slider bolts with approved brake grease.
  4. Install the brake pads onto the bracket assembly, and then carefully lower the caliper over the caliper mount. Check and make sure that the pad springs are correctly seated.
  5. Replace all removed caliper-to-sliding pin bolts and torque to:
  6. 1990-97 Passat models: 25 ft. lbs. (35 Nm)
  7. 1998-00 Passat models: 22 ft. lbs. (30 Nm)
  8. If equipped, connect the brake wear sensor wire to the harness. Check for a good connection as most problems with the sensor circuit are caused by faulty connections. Check that the wire is held by the loop in the dust cover and the connector is held at the clips.
  9. Install the wheels and hand tighten the lug bolts. Lower the vehicle carefully until the tires begin to contact the surface and torque the lug bolts to specification in a crisscross pattern to:
  10. M12 x 1.5 lug bolts: 81 ft. lbs. (110 Nm)
  11. M14 x 1.5 lug bolts: 89 ft. lbs. (120 Nm)
Feel free to contact if you have any questions

Posted on Nov 15, 2008

Ad
motor1258
  • 6674 Answers

SOURCE: rear brake pad installation 99 volkswagen Passat

I use a "C" clamp & screw it in slowly. If need be, leave cap of reservoir, and/or crack open your bleeder screw. Bleed after install.

Posted on Dec 30, 2008

  • 59 Answers

SOURCE: The clock in my Volkswagen Touareg is wrong.

On your steering wheel there is a button bottom right it should look like two squares. That is the menu button. Scroll through the menu settings until Time appears. Push in on the thumb wheel above the menu button to select. After that roll the wheel up or down to adjust the time and press in when finished.

Posted on Jan 10, 2009

pippall
  • 1486 Answers

SOURCE: reset computer on 2004 Touareg

Drive the car at about 10 mph then if there is no fault the light will go out.Failing that remove the baterry wires and leave off for an hout then replace.That should cllear the code.Make sure you have the radio code before you disconect the baterry.Hope that was helpfull.Good luck.

Posted on Jul 28, 2009

  • 312 Answers

SOURCE: Brake Pad Replacement,2004 VW Touareg,V6 instructions

Same as any other vehicle.

1. Raise and support vehicle
2. Remove tire/wheel
3. Loosen/remove the two caliper bolts
4. Slide caliper off the rotor.
5. Use a C-Clamp to depress the caliper piston
6. Remove old pads from caliper
7. Install new pads on caliper
8. Install caliper/tighten caliper bolts
9. Install tire/wheel
10.Lower vehicle
11 Move to next wheel/repeat

Some people take a turkey baster and remove some of the brake fluid from the master cylinder prior to depressing the caliper piston because it can over flow. If you choose to do that just add the fluid back when finished so it is at its proper level.

Posted on Sep 12, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Rear mounted wheel on my touareg squeaks when


The wheel or tire doesn't squeek
The suspension,brakes or exhaust may
If you talking a wheel mounted on the back
not on the axles surely you can figure that out

Aug 12, 2013 | Volkswagen Touareg Cars & Trucks

1 Answer

HOW TO WIRE BRAKE LIGHTS FROM THIRD LIGHT 97 MONTE CARLO


Instead of improvising, why not get the stop lamps working the way they should be. You must be getting power through 15A fuse 23 in the fuse block and the stop lamp switch, otherwise the high mounted stop lamps would not work. Stop lamp power is routed through the turn signal switch and is applied to the tail/turn/stop-lamps. That should solve your problem

Oct 17, 2012 | 1997 Chevrolet Monte Carlo

1 Answer

Do I remove the entire cover or the little door thats atached to this cover on the passenger side? There are 3 brake lights that were recommended to replace. Driver side and passenger side plus the third...


Lamp, Rear Hi-Mount Lamp Assembly
Removal
  1. Disconnect the battery ground cable (14301) .
  1. Raise the liftgate.
  1. Remove the liftgate door trim panel (46404) . Refer to Section 01-05 for the removal procedure.
Trim Panel, Liftgate Door Removal
  1. Disconnect thebattery ground cable (14301) .
  1. On vehicles with a rear window wiper, remove the three rear wiper motor cover screws and remove the rear wiper motor cover.
  1. Pry the liftgate door trim panel (46404) away from the liftgate.
  1. Disconnect the luggage compartment lamp electrical connector.

    n11098a.gif

  1. Remove the liftgate door trim panel
  1. Rotate the rear hi-mount lamp socket counterclockwise and remove it from the rear hi-mount lamp (13A613) .

    k20521a.gif

  1. Remove the two rear hi-mount lamp housing nuts and remove the rear hi-mount lamp lens and housing.

    k20523a.gif

Oct 18, 2010 | 1995 Ford Aspire

1 Answer

How do i change a brake light bulb on 2000 vw jetta?


Removing:
  • Switch off all electrical consumers, switch off ignition key and remove ignition key.
  • Remove rear luggage compartment side panel trim (left or right).
98971821.gif
  • Remove 3 nuts, arrows, and remove housing.
  • Remove bulb holder.
Installing:
  • Install bulb holder.
  • Insert housing into body opening.
  • Tighten nuts.
  • Install applicable rear luggage compartment side panel trim.
Rear Light Bulb Holder Removing And Installing:
Removing:
  • Disconnect electrical connector.
  • Depress retainers, arrows, and remove bulb holder.
98971817.gif Installing:
  • Install in reverse order of removal.
And the Center Mounted Brake Lamp.
High mount Brake Light Removing And Installing:
The high mount brake light is installed in the rear shelf.
98971288.gif Removing:
  • Switch off all electrical consumers, switch off ignition key and remove ignition key.
  • Disconnect electrical connector from high mount brake light.
  • Remove rear shelf
  • Un-clip high-mount brake light from rear shelf, arrows.
  • Install in reverse order of removal.
NOTE: The bulb holder base plate contains soldered- in light emitting diodes (LEDs) that are not replaceable. In the event of LED malfunction, replace complete bulb holder.
Additional

Mar 13, 2010 | 2000 Volkswagen Beetle

1 Answer

Rear brake lights will not turn off - 2004 touareg


Quick...pull the fuse for the stop lights so you don't kill the battery! By far the most common problem is the brake light switch.

Sep 24, 2009 | 2004 Volkswagen Touareg

1 Answer

Touareg 04 rear driveshaft replacement


By the labour book I use it says 2.9 hours to remove the driveshaft plus another .5 to change the bearing.

May 25, 2009 | 2004 Volkswagen Touareg

1 Answer

Touareg Brake light replacement


There is also a locating lug on the lamp that slides over a slotted groove,When the 2 screws have been removed grab the lamp firmly and pull to the rear this will free the lamp from its location and allow access to the bulb holder.

Oct 18, 2008 | 2004 Volkswagen Touareg

Not finding what you are looking for?
2005 Volkswagen Touareg Logo

Related Topics:

40 people viewed this question

Ask a Question

Usually answered in minutes!

Top Volkswagen Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

yadayada
yadayada

Level 3 Expert

76649 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8518 Answers

Are you a Volkswagen Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...