Question about Cars & Trucks

1 Answer

What size is the CV axle nut to a 1997 sunfire Pontiac

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Cars & Trucks Master
  • 816 Answers

29mm socket! I think this is the right size, but call any auto parts store to find out for sure.Good-Day!

Posted on May 17, 2014

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 124 Answers

SOURCE: axle nut size

it could be 36mm

Posted on Apr 06, 2009

wireguy212
  • 1627 Answers

SOURCE: what size is the nut on the cv axle

G.M. uses a metric nut,you need a 30mm socket.

Posted on Oct 19, 2009

  • 1 Answer

SOURCE: step by step removal of cv axle on a 97 4x4 and

36 mm

Posted on Oct 23, 2009

  • 641 Answers

SOURCE: cv axle nut

I believe it is a 36mm

Posted on Nov 17, 2009

wireguy212
  • 1627 Answers

SOURCE: size of socket ineed for a axle nut on 1999

You need a 30mm socket,the nut should come almost off before you even lift the car off the ground[unless you have a good air impact driver].

Posted on Jan 16, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What size is the axle nut on a 2000 Pontiac sunfire


Spindle Nut:
Thread: M20-1.5; Hex Size: 30mm; Height: 19mm

Nov 04, 2016 | 2000 Pontiac Sunfire

1 Answer

What is the axle nut size on a 2000 and a 2004 Pontiac sunfire are they the same?


Spindle Nut:
Thread: M20-1.5; Hex Size: 30mm; Height: 19mm

2000 and 2004 are the same size.

Nov 04, 2016 | Pontiac Sunfire Cars & Trucks

1 Answer

Left front axle seal leaking how to get the stub shaft out of transmission


I would use a pry-bar and have my free hand hold the bottom of the CV-joint while prying on it having the pry-bar resting on the trans if it wont break anything on the trans.

Dec 27, 2010 | 1997 Pontiac Sunfire

1 Answer

How to change a Cv joint on a 1997 Pontiac Grandam


While the car is still on the ground remove the half shaft nut then jack the car up and support it with jack stands and remove the tire. after you get the tire off you may have to remove the break caliper and the rotor, if you have to do this now. Remove the lower ball joint nut and break apart the ball joint with a large pry bar by prying down on the lower a frame. grab the steering knuckle with both hands and pull until the half shaft is free from the bearing hub assembly. then grab the half shaft and give it a good tug to remove it from the trans axle, you may have to pry it out with a small pry bar wedged between the inner cv joint and the trans axle. at this point I would replace the entire half shaft it is cheaper and a lot easier than replacing the cv joint. installation is reversed but be careful of the splines when installing the half shaft back into the trans axle and the bearing hub. Good luck.

Nov 02, 2010 | 1997 Pontiac Grand Am

1 Answer

Changing cvc joints 1997 accord


replace the entire CV axles. Support vehicle with jackstands by frame. Remove front wheels. Remove axle nuts. Remove lower balljoint nut. Separate balljoint from nuckle by banging hard with ball peen hammer on knuckle on spindle assy. Remove outer tie-rod nut. Separate tie-rod from steering nuckle by bangin on nuckle with ball-peen hammer. Use long pry bar to hold lower control arm down while simultaneously pulling hub/spindle assembly away from vehicle and pushing axle through hub toward transaxle. Go under vehicle and pry inner cv joint away from transaxle while holding axle assembly.
Install new CV axle in reverse of the disassembly.

Feb 21, 2010 | 1997 Honda Accord

1 Answer

Size of socket ineed for a axle nut on 1999 pontiac grandam


You need a 30mm socket,the nut should come almost off before you even lift the car off the ground[unless you have a good air impact driver].

Jan 16, 2010 | 1998 Pontiac Sunfire

1 Answer

I need to get the cv joint off the end of the axle shaft in order to get the new boot on how do i do it? i am replacing the inner cv boot and cant get the cv joint off what do i do. thank you


the following sites r helpful http://www.automedia.com/CV_Rehab/ccr20021101cv/1 and http://www.youtube.com/watch?v=JVoalhTM74U courtesy of fixya guru knight007 who has advised others with the above sites

Nov 11, 2009 | 1997 Pontiac Sunfire

1 Answer

What size is the axle nut on the cv joint on a 1998 pontiac sunfire?


I remove with a 29 mm. thaty is the perfect size but 1 3/16 socket will also do the job.

Apr 07, 2009 | 1998 Pontiac Sunfire

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

38 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76109 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...