Question about 1997 Dodge Grand Caravan

1 Answer

My car signal stop funtion

Why all signal stop working turn left turn right etc. none of em work. I check the fuse all good no blow out. any one got an idea please?

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Dodge Master
  • 816 Answers

Have you checked the turn signal relay! It is above your left leg under the fuse access. under dash. do your emergency flashers work, because the relay is a combination relay for e-flashers and turn signals. if the flasher unit is ok, you may have a bad bulb or a short to ground.

Posted on May 17, 2014

Testimonial: "my emergency flashers work fine. but wiper don't work, mirror adjustment left/right not work, horn no work all signal no work. Thanks for your reply."

  • anexkajun
    anexkajun May 21, 2014

    emergency work fine tail ligh bult fi9ne too what else could it cost this problem? Thanks

×

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

3 Answers

Turn signals not working


all else on car works perfectly (other shoe drops??????)
waring 1: no scan tool, you will fail (99%)
is battery fully charged to 12.6vdc rested or at 10v?
all 4 corners dead?
not working means dead?, flashes too fast/slow or dim? or they stick on? (5 modes to fail not counting L/R and haz)
do the hazards work? (prime evidence and not stated)
most cars before 2007 have fuse marked TURN.
but not this car... its not at all like older cars....
did you scan it first after the fuse tests? any PCM scan tool.?
2009 WK jeep
the FSM chapter 8L shows the huge list of errors the lamps can fail. DTC errors.
in fact 8 blinker codes, ! DTC errors,

there is no fuse, just for turns, (trailer lamps fuse 19)

read this excerpt from the FSM book.

The turn signal system operates on battery current received on a fused ignition switch output (run) circuit so that the
turn signals will only operate with the ignition switch in the On position. The hazard warning system operates on
non-switched battery current received on a fused B(+) circuit so that the hazard warning remains operational regardless
of the ignition switch position. When the turn signal system is activated, the circuitry of the left multi-function
switch and the FCM will cause the selected (right or left) turn signal indicator, front park/turn signal lamp, front side
marker lamp and rear tail/stop/turn signal lamp to flash on and off. When the hazard warning system is activated,
the circuitry of the hazard warning switch and the FCM will cause both the right side and the left side turn signal
indicators, front park/turn signal lamps, front side marker lamps and rear tail/stop/turn signal lamps to flash on and
off. The Front Control Module (FCM) can also activate the hazard warning system lamps.
end quote)

the module front control MFC, runs this
and it uses fuse 18 , if 18 blows the module goes off line and vast things fail and huge numbers OF DTCs store.
and fuse 27 MFC
MFC needs these fuses good.
keep in mind nobody has MFC internal schematics...so........



this module drives left and right side front and rear.
electronic drivers, not fuses.
the MFC is here.
the fuses are 12,13,18, 20,27 that power MFC.


25812039-lb3yimx2pwhstnjl4tgwffiq-2-0.jpg ground this end.

Aug 07, 2015 | 2009 Jeep Grand Cherokee

1 Answer

2002 Pontiac Grand Am turn signals not working. Could this be a fuse?


None work , left , right , front or back ? Check TURN LPS fuse C 10 Amp -in Left instrument fuse panel ! More then likely it's the switch on the steering column or the hazard switch , power for turn signals come from the hazard switch !
Fuse Block - Left I/P- On the left side of the I/P

May 27, 2015 | 2002 Pontiac Grand Am

1 Answer

1987 ford ranger turn signals keep blowing fuses. have changed flasher fuse and switch on column. just keeps blowing?


first thing i guess to understand what is going on here ,is a little back to basics on how turnsignals work , first item you have is power fuse then it's off to flasher module than it goes to the turnsignal switch on colum ,of course anywhere on it way to there the power could got to ground and cause the fuse to trip, now the power depending on Left or right selection , is directed to lights on both front and back of truck,thankfully rangers don't have em on the side) now any place in this pathway the wire could go to ground and blow the fuse, now to troubleshoot and narrow down the area that fault is located , (1) replace fuse with correct size and ck for proper fit in fusebox and start and operate truck for a few minutes DO not use turnsignals, ck fuse is it still good if so go to step 2 if not stop and ck wire conditions in steering colum and switch(2) start truck and try right hand turn signal only verify lights working ,Ok yes/no if not replace fuse and try left side same way, Ok yes /no if right or left side only blows fuses take ALL bulbS OUT of lights and try again , if fuse still blows then look for wire fault on that side of truck if fuse is still good then look carefull at light bulb sockets for rust and powered corrosion (ill bet an 87 has some ) you may need to replace bulb sockets , they do sell em in autoparts stores .

Jun 30, 2014 | 1987 Ford Ranger

2 Answers

Both of the rear turn signals stopped working at the same time, but everything else seems to work. Do you know what can cause this to happen? I changed one of the bulbs and it didn't work.


There is a turn signal flasher under dash...most have a flasher for the emergency signals and one for the turn signals...some have one flasher....but check fuses first...normally it is fuse burnt...if you can locate the flasher normally they will get abnormally warm when bad......it should look like a round or square silver shiney or black cube.........if these are good with ign.on hold turn signal lever down firmly ...if it works replace turn signal unit.....if none of this works you have to troubleshoot wiring...
...normally yellow wire is left turn and green wire is right turn...black or white is ground red is stop light....but normally it is a blown fuse or flasher.

Feb 19, 2011 | 2007 Ford Freestyle Limited

1 Answer

Left turn signal outside lamp, front and back do


Inspect the turn fuse under the hood. There are seperate fuses for L and R

Feb 06, 2010 | 2003 Chevrolet Silverado 1500

1 Answer

1985 suburban bad Electrical i think??


CHECK THE FUSE BOX FOR BAD FUSES. SOME OF THE TRUCK MODELS ALSO HAVE A BUSS BOX UNDER THE HOOD ON THE FENDERWELL FOR A TOW PACKAGE,ETC. CHECK EM ALL FOR CONTINUITY

Aug 25, 2009 | 1985 Chevrolet Suburban

1 Answer

It has no turnsignals.They dont even light up. The 4ways work fine.


well first off lets clear a few things 4ways are wired in with the break switch not the turn signal switch so yes even if the turn signals dont work the 4 ways might and vise versa...
if this was a car in my shop i would first check the fuse, if thats ok check the multi funtion switch see if the signal is going out from there, I am sorry now if its the multi funtion switch they are $$$ to replace most of the time when i get this kind of problem in its the multi switch they have plastic tabs in them that push the contacts together and they break off and stop working, but then again if all your turn signals are not working its probly the fuse. post comment if you need more info
good luck

Aug 21, 2009 | 1988 Ford Taurus

1 Answer

Indicator lights no longer blink its one solid light


Im Not Totaly Sure But Most other Makes & Modles Ues 2 Seperate Signal FLASHER Units
Your Owners Manual Should Show this As Turn Signal "FLASHER" Located At or Near Fuse / Relay Box This is ASUMING you have Checked The Fuses and Relays

Feb 09, 2009 | 2000 Mazda Protege

1 Answer

1998 Dodge Ram 1500 4WD blowing fuse when turning left signal on


left side u got a short
u can wire up a buzzer or light to plug into where the fuse goes that blows when u turn on ur left blinker the buzzer will sound or the light will come on ,while the buzzer is on take apart left signals
and check wiring by moving harness around ,when u find the short the buzzer will quit

Jan 21, 2009 | 1998 Dodge Ram 1500 4WD

Not finding what you are looking for?
1997 Dodge Grand Caravan Logo

247 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

76109 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8269 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...