Question about 2001 Ford Explorer Sport

2 Answers

Keyless Entry System

Keybob will not work

Posted by on

2 Answers

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Expert
  • 108 Answers

The meaning of fob is finger operated button. You will have to replace the battery . Some hardware stores will doe them and some lock smith will do them , or take it too the dealer ship and go to the part dep. and they can help you. Good luck

Posted on May 17, 2014

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Ford Master
  • 937 Answers

First thought is bad battery. See
https://www.youtube.com/watch?v=8FfAPK1jmUo

for replacement guidance.

Posted on May 17, 2014

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 1596 Answers

SOURCE: Does it have keyless entry--2005 Ford F-150

Take it to Dealer They Can Determin this By the VIN Number and They Also Have The Fob & Can Program it For You

Posted on Feb 11, 2009

chuck943
  • 783 Answers

SOURCE: CHANGE CODE ON KEYLESS ENTRY SYSTEM FORD EDGE

Yes you can program your own code by inputting the original code then hit the no. 2 button then input your own 5 digit code.

Posted on Mar 16, 2009

  • 334 Answers

SOURCE: how do reprogram my keyless entry pad to a 1995

look in your owner manul it should tell you . or go to a dealer they will be abele to tell you

Posted on Nov 11, 2009

ftw1952
  • 10319 Answers

SOURCE: Keyless entry only works at very close range.

Batteries new or old? It will make a difference if old and new

Posted on Jan 26, 2010

  • 6 Answers

SOURCE: keyless entry system will not

Have you checked the battery in the key fob?

Posted on Mar 02, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

2003 Yukon xl horn problem


The vehicle horns are activated under the following conditions:
?€¢
The horn switch is depressed.


?€¢
The body control module (BCM) commands the horns on. The BCM commands the horns on under either of the following conditions:


-
When the content theft deterrent system detects a vehicle intrusion. For further information, refer to Content Theft Deterrent (CTD) Description and Operation in Theft Deterrent.


-
When the panic button is depressed on the remote control door lock transmitter. For further information, refer to Keyless Entry System Description and Operation in Keyless Entry.


-
When the OnStar?® system is used to sound the horns, if equipped. For further information, refer to OnStar Description and Operation in Cellular Communications.


-
When the keyless entry system is used to lock the vehicle, a horn chirp may sound to notify the driver that the vehicle has been locked. The notification feature may be enabled or disabled through personalization. For further information, refer to Keyless Entry System Description and Operation in Keyless Entry

Jun 22, 2016 | 2003 GMC Yukon XL 1500 SLT

1 Answer

I have a 96 ford conversion van with a 600 plus addon keyless system and need to program new keyless remots , need to know how to get system in program mode.


Hi.

To program ( or reprogram ) a keyless entry remote transmitter into the remote keyless entry module, perform the following steps:

1. Turn the key to ON or ACC and short the two terminals of the program connector, a two-pin connector located below the driver's side of the instrument panel at the base of the steering column. All doors should lock and then unlock.
2. Press any button on each keyless entry remote transmitter in turn. All doors should lock and then unlock. If the door locks do not respond, press the button again (up to three times maximum with the same keyless entry remote transmitter). If the door locks still fail to respond, go to Pinpoint Test A.
3. Repeat Step 2 to program additional keyless entry remote transmitters into the remote keyless entry module (up to four keyless entry remote transmitters maximum).
4. Turn key off.
5. Remove the short from the program connector. All doors should lock and then unlock.
6. Verify that the keyless entry remote transmitters have been successfully programmed by pressing the LOCK or UNLOCK button on each one, and observing that the system responds by locking and/or unlocking the doors.


I hope this helps you.

Thanks!

Nov 28, 2010 | 1996 Ford Econoline

1 Answer

Keyless remotes not working


Try reprogramming the remotes. Here are the instructions for the procedure. Hope it helps. Cobra!
Programming NOTE: All keyless entry remote transmitters (15K601) must be programmed at the same time.
NOTE: To program (or reprogram) the keyless entry remote transmitters into the RAP module, perform the following steps:
  1. Make sure that the anti-theft system is not armed or triggered.
  1. Turn the ignition switch (11572) from OFF to RUN eight times within ten seconds, ending in RUN. If the RAP module has successfully entered program mode, it will lock and then unlock all doors.
  1. Within 20 seconds, press any button on a keyless entry remote transmitter, and the doors will lock and then unlock to confirm that each keyless entry remote transmitter has been programmed. Repeat this step for each transmitter.
  1. If the door locks do not respond for any keyless entry remote transmitter, wait several seconds and press the button again. If the door locks still fail to respond, refer to Inspection and Verification.
  1. Turn the ignition switch to the OFF position, or wait up to 20 seconds after step 2, to exit program mode. If a keyless entry remote transmitter has been programmed (or reprogrammed), the RAP module will lock and unlock all doors one last time to confirm.

Jun 06, 2010 | 1998 Ford F150 Regular Cab

1 Answer

How do i reprogram electronic door locks


Programming Electronic Door Lock Control System NOTE: The electronic door lock control processor (14B001) erases all previous keyless entry remote transmitter (15K601) from memory when the keyless entry remote transmitters are programmed or reprogrammed. The electronic door lock control processor can store up to four keyless entry remote transmitters in memory.


  • To program (or reprogram) keyless entry remote transmitter into the electronic door lock control processor, perform the following steps:
  1. Turn ignition switch to the RUN position and momentarily short the two terminals of the program connector taped to the wire assembly and located behind the glove compartment. All doors should lock and then unlock. Remove shorting pin.
  1. Press any button on keyless entry remote transmitter. All doors should lock and then unlock to verify the keyless entry remote transmitter has been programmed. If door locks do not respond, press button again (up to three times maximum with the same keyless entry remote transmitter).
  1. Repeat the above step to program additional keyless entry remote transmitters into the electronic door lock control processor (up to four keyless entry remote transmitters maximum).
  1. Turn ignition switch OFF. All doors should lock and then unlock.
  1. Check operation.

Jun 05, 2010 | 1997 Ford Windstar

1 Answer

2001 Chevy cavalier Z24 keyless entry not working.


You should have it scaned to see if you have any codes. It has a RCDLR (remote control door lock reciever) this is the module that recieves the signal from the fobs. If it has a problem then the system will not work. If it has to be replaced then a dealer will have to program it for you. Good Luck

May 25, 2009 | 2001 Chevrolet Cavalier

1 Answer

Keyless entry on honda civic 2006 not working


The keyless entry is designed to work with the doors closed (closed - not locked). If the door ajar sensor thinks the door is open the keyless entry is disabled. When you manually lock the door it might tighten the door just enough to activate the keyless entry. I would try slamming all the doors closed and then see if the keyless entry works. If it still wont work have the wiring checked on the front door lock.

May 12, 2009 | 2006 Honda Civic Hybrid

1 Answer

Intall Remote Keyless Entry System in an 02 Honda Accord


You got the Wrong Information! Go to Wal Mart and Purchase a "Bulldog Security Keyless Entry" System for your Car. It will cost you a Quarter of the Price and is Just asw Reliable as the Factory Unit! Got one on My Truck with Remote Start also and it works GREAT! Should cost about $50.00 Bucks or so.

Jan 22, 2009 | 2002 Honda Accord

1 Answer

Keyless entry not working


the keyless entry system is tied into the computer system and needs to reprogramed by the dealership

Nov 30, 2008 | 2004 Jeep Grand Cherokee

2 Answers

2001 Dodge Ram 1500 Keyless Entry/Security System


Your keyless/security system may have been damaged by the spikes. But, assuming you've already checked all the fuses, I would start by having the alternator tested. I would also check the alternator wire connection to the power distribution center (pdc). It can loosen and cause different problems.

Good Luck!

Jul 28, 2008 | 2001 Dodge Ram 1500 Truck 2WD

Not finding what you are looking for?
Cars & Trucks Logo

26 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

fordexpert

Level 3 Expert

5501 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...