Question about 2006 Chrysler Pacifica

1 Answer

How to I reinstall the center console wiring attachments in a 2006 pacifica. I have changed out my shift interlocking latch because it was broken and I have a wiring harness with 3 wires that I don't

The tree wires are orange and gray, black and white and green and white that come from the front of the car ever to the left where they are attached and have a cloth like material covering on them. Where do they attach?

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    New Friend:

    An expert that has 1 follower.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 63 Answers

Some models have an extra wire plug-in that would go to a light or temp controls on the very back of console. not all models have these options but all models have the extra plug-in. its cheaper for them to make one "fits all harness" than several different ones

Posted on May 19, 2014

3 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 118 Answers

SOURCE: I have broken wire harness on the back of my Heater/AC automatic climate control. The black harness on the back has 11 different colored wires. Do you know which color wires go on which pins in the ba

Check the dealer to see if they have a pig tail to wire in. if so the new pigtail should have same wire color for matching up.

Posted on Jun 14, 2012

  • 747 Answers

SOURCE: What is the black and green wire attached to the 1991 Chrysler Labaron radio used for?

this may be the memory wire for the factory unit if putting in an after market radio you shouldn't need it

Posted on Jun 28, 2012

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

99 mercury cougar radio wiring diagram


1999 Mercury Cougar Car Stereo Wiring Diagram
Car Radio Battery Constant 12v+ Wire: Orange/Black
Car Radio Accessory Switched 12v+ Wire: Yellow/Green
Car Radio Ground Wire: Black/Green
Car Stereo Dimmer Wire: White/Green
Left Front Speaker Positive Wire (+): White/Black
Left Front Speaker Negative Wire (-): Gray/Black
Right Front Speaker Positive Wire (+): White/Red
Right Front Speaker Negative Wire (-): Gray/Red
Car Audio Rear Speakers Location: Side Panels
Left Rear Speaker Positive Wire (+): White/Purple
Left Rear Speaker Negative Wire (-): Gray/White
Right Rear Speaker Positive Wire (+): White
Right Rear Speaker Negative Wire (-): Gray

1999 Mercury Cougar Car Stereo Wiring Diagram ModifiedLife com

Feb 08, 2017 | Mercury Cougar Cars & Trucks

1 Answer

The linkage are hooked up but the car still want go into park,a 2000 Taurus


Do you have floor console shifter ?
Shift Interlock System A brake/shifter interlock system consists of the following:
  • ignition switch (11572)
  • brake pedal stoplight switch (13480)
  • brake shift interlock module
  • brake shift interlock solenoid assembly (attached to key interlock assembly)
  • necessary wiring
On floor-shift vehicles, the ignition/shifter interlock cable (3F719):
  • locks the floor shift transaxle range selector lever in the PARK position when the ignition switch is in the LOCK position.
  • requires the floor shift transaxle range selector lever to be in the PARK position to turn the ignition switch to the LOCK position.

May 04, 2015 | 2000 Ford Taurus

1 Answer

2006 impala lt shifter solenoid location


Shift interlock solenoid locatex on shifter have to remove shifter bezel and possibly console and its usually a broken wire at plug that gives trouble

Feb 24, 2015 | 2006 Chevrolet Impala

1 Answer

How to install a center console on a pacifica


Hi Melissa, I'm glad to help, here is the instruction below I said I'd send. Have an awesome day.


23 - Body/Interior/CONSOLE, Floor, Front/Removal REMOVAL [img id=LOPTableImg src="https://w05.dealerconnect.chrysler.com/service/mds2002/common/images/collapse.gif"> Click to display a list of Labor Operations associated with this procedure 1. Remove shift bezel. (Refer to 23 - Body/Interior/BEZEL, Shifter - Removal) .
2. Remove transmission range indicator surround bezel Figure 1.
3. Remove two screws attaching front floor console to the lower instrument panel Figure 2. 4. Open cup holder and remove two attaching screws to bottom of cup holder. 5. Open bin and remove two attaching screws to bottom of bin. 6. Remove front floor console sidewall attaching screws, three per side. 7. Raise front floor console and disconnect wiring harness. 8. Remove front floor console from vehicle.
374297.jpg Figure 1 - TRANSMISSION RANGE INDICATOR SURROUND BEZEL 1 - INSTRUMENT PANEL 2 - AUTOSTICK SHIFTER ASSEMBLY 3 - TRACTION CONTROL SWITCH 4 - TRANSMISSION RANGE INDICTOR SURROUND BEZEL 5 - KNOB SET SCREW 6 - SHIFTER KNOB 7 - FLOOR SHIFT BEZEL 8 - WIRE CONNECTOR 9 - INSTRUMENT PANEL WIRING HARNESS 10 - INSTRUMENT PANEL WIRING CLIP
374299.jpg Figure 2 - FRONT FLOOR CONSOLE 1 - FORWARD CONSOLE CLOSEOUT PANEL 2 - CLOSEOUT PANEL PUSH PIN RETAINER 3 - INSTRUMENT PANEL WIRING 4 - FLOOR CONSOLE BASE 5 - FRONT FLOOR CONSOLE ATTACHING SCREWS TO LOWER INSTRUMENT PANE AND BASE 6 - FRONT FLOOR CONSOLE WIRING CONNECTOR 7 - FRONT FLOOR CONSOLE 8 - ATTACHING L-BRACKETS

May 17, 2014 | 2006 Chrysler Pacifica

1 Answer

I'm an idiot and put my engagement ring in my change holder in my 2006 Chrysler Pacifica. When I went to put it back on, it was no where to be found. I believe it slipped behind the small crack


Print I hope this helps you,good luck.Randy


Removal & Installation

Instrument Panel

  1. Disconnect and isolate the battery negative cable.
  2. Remove the center console closeout panel by removing the left and right attaching screws, then the left and right panels.
  3. Remove or disconnect the following:

    Remove the shift bezel. Remove the transmission range indicator surround bezel. Remove the two screws attaching the front floor console to the lower instrument panel. Open the cup holder and remove the two attaching screws on the bottom of the cup holder. Open the bin and remove the two attaching screws on the bottom of the bin. Remove the front floor console sidewall attaching screws, three per side. Raise the front floor console and disconnect the wiring harness. Remove the front floor console from the vehicle.

    0996b43f807cb4f3.jpg enlarge_icon.gifenlarge_tooltip.gif

    Fig. View of front floor console and shift bezel


    0996b43f807cb4f4.jpg enlarge_icon.gifenlarge_tooltip.gif

    Fig. View of front floor console, showing attaching screws

  4. Remove the floor console base assembly by removing the two screws attaching the L-brackets to the instrument panel.
  5. Remove the nuts attaching the floor braces to the instrument panel.

    0996b43f807cb4f5.jpg enlarge_icon.gifenlarge_tooltip.gif

    Fig. View of floor brace, attaching nuts, center brace, and floor bracket

May 02, 2012 | 2006 Chrysler Pacifica

1 Answer

Need radio wiring diagram for 1988 jeep comanche


  • Constant 12V+ Pink
  • Switched 12V+ Purple/Orange
  • Ground - Black
  • Illumination - Orange/Black
  • Dimmer - Dark Blue/White
  • Antenna Trigger - Gray
  • Front Speakers - 5 1/4" Doors
  • Left Front (+) - Green
  • Left Front (-) - Black/Yellow
  • Right Front (+) - White
  • Right Front (-) - Black
  • Rear Speakers - 5 1/4" Tail Gate
  • Left Rear (+) - Gray/White
  • Left Rear (-) - Brown/White
  • Right Rear (+) - White/Black
  • Right Rear (-) - Brown

Oct 27, 2011 | 1988 Jeep Comanche

1 Answer

Installing aftermarket stereo in 99 silverado which wires from stock harness connest to aftermarket harness


connect the wires as indicated below

1999 Chevrolet Silverado C1500 Wiring, aftermarket stereo wire colors

Car Radio Battery Constant 12v+ Wire: Orange, yellow
Car Radio Accessory Switched 12v+ Wire: Yellow, red
Car Radio Ground Wire: Black, black
Car Radio Illumination Wire: Gray (Tape off) not used
Car Stereo Dimmer Wire: Brown (Tape off) not used
Left Front Speaker Positive Wire (+): Tan, white
Left Front Speaker Negative Wire (-): Gray, white/black
Right Front Speaker Positive Wire (+): Light Green, gray
Right Front Speaker Negative Wire (-): Dark Green, gray/black
Left Rear Speaker Positive Wire (+): Brown, green
Left Rear Speaker Negative Wire (-): Yellow, green/black
Right Rear Speaker Positive Wire (+): Dark Blue, purple
Right Rear Speaker Negative Wire (-): Light Blue, purple/black

Oct 22, 2011 | 1999 Chevrolet Silverado 1500

4 Answers

My 2007 chrysler pacifica wont shift out of park.


SHIFTER LOCKED IN PLACE

  1. Remove the instrument panel cover below the steering column, then remove the steering column shrouds to gain access to the brake transmission shift interlock (BTSI) solenoid. The solenoid is part of the interlock cable assembly.
  2. Disconnect the wire connector from the rear of the BTSI solenoid.
  3. Insert the ignition key and turn it to the ON position.
  4. With the brakes applied, try moving the shifter out of the PARK position.
    • If the lever now moves freely in and out of PARK, perform the Circuit Test below.
    • If the shift lever still does not move from the PARK position, remove the BTSI solenoid from the shift lever assembly. If the shift lever now moves freely in and out of the park position, the BTSI solenoid is faulty and the interlock cable must be replaced. If the shift lever still does not move from the park position, the problem is in the shift lever assembly or the ignition interlock cassette

Aug 14, 2011 | 2007 Chrysler Pacifica FWD New Cars

2 Answers

2006 chrysler pacifica - drove car into my garage and shut down. Next morning I could not get the car to shift out of park.


some are set up with safety with brake lites out. ck if brake lites work if not turn key on do not start and shift to neautral and start and have brake lites repaired

Jun 03, 2011 | 2006 Chrysler 300

Not finding what you are looking for?
2006 Chrysler Pacifica Logo

103 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8215 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...