Question about 2004 GMC Sierra 2500

1 Answer

Cruise control not working on vectra 2.0 diesel 2005 I have tried brake and clutch switches any fresh ideas

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 76 Answers

Though I'm not familiar with the Diesel, most vehicles have two throttle cables. One is for the cruise and it's common for the plastic part at the end (throttle body) to break. This is the easiest fix, and very commonly the problem. Good Luck

Posted on May 17, 2014

Testimonial: "I have electronic system so no cables"

  • mwit465
    mwit465 May 18, 2014

    In that case, have you checked the fuses

  • leone ciantar
    leone ciantar May 18, 2014

    thanks I did and also scanner is not giving any faults

×

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 37 Answers

SOURCE: cruise not working

If any break lights are on, thats probably your problem. When your press the brake the cruise cuts off. (All Vehicles I know of)

Posted on Jul 01, 2009

  • 462 Answers

SOURCE: cruise control does not work

Have you had this campaign done yet?

06030: Product Safety - Brake Lamps Inoperative or Continuous Illumination

If the switch is malfunctioning the cruise control will not engage.

Posted on Sep 03, 2009

  • 1 Answer

SOURCE: Vauxhall Vectra Cruise control problem

try lifting the brake pedal with your toes then switching on the cc when driving. sometimes a faulty or loose switch on the brake pedal can cause cc to cut out.

Posted on Aug 17, 2009

  • 432 Answers

SOURCE: 1990 GMC Sierra 1500 pickup. Windshield wipers, Cruise Control

May want to look at replacing the wiper circuit board.It is located on the firewall adjacent to the wiper motor and has a some what square black cover with 3 torx screws and wireing harness pluged into the side.We had a truck that every time you washed it the wipers would stay on until it dryed out.You can try removing it and spaying it down with contact cleaner just watch the brease on the two contact tips.Well hope this helps.

Posted on Feb 05, 2010

riceski
  • 1851 Answers

SOURCE: I have 1998 gmc 3/4 ton auto . a.b.s light comes on intermitantly. when it does I also loose my full heater controls and cruise control. new brake switch has been instaled but c'ant see how that would

It is coincidence that your heater control went at the same time your ABS control went out. Try replacing the ABS control and see if that fixes it. Many times because of the electrical complexity you have to just start replacing things until you get it unless you own one very expensive computer.
Look for loose wires. Also try it in reverse if you like. Replace the heater control and see if that fixes it all. Also check ALL fuses.

Posted on Dec 07, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Why doesn't the cruise control work?


run the fault codes
cruise control needs the following to work together as one or more will stop it from working.
VSS sensor, (road speed /speedo)
engine rpms/tacho
brake switch sensor/
clutch switch sensor
cruise control switch

Jun 06, 2015 | 2005 SsangYong Rexton RX

1 Answer

Vauxhall vectra sli cruise controll not working


The cruise control is normal disengaged by applying a little pressure to either the clutch or brake pedal. There are switches/sensors on the top of these pedals near the return springs. The retuns springs become weaker with time/use, so it is possible that they are not fully returning to allow disengage to reset so that it can be used again.
That is the cheapest fix and should be the first check.
The next is to cange the stalk as the switch at the end may be broken. Costwise it is relatively inexpensive for a replacement and to instal yourself. Make sure you've done the first part, or else you'll waste money and time.
Good luck.

Nov 20, 2013 | Vauxhall Cars & Trucks

1 Answer

CRUISE CONTROL WON'T WORK ON 2005 CHEVY TRAILBLAZER


check cruise control fuse and check the brake lights see if brake light working because the brake light switch will deactivate cruise control when brakes is applied.if brake lights dont work either fuse blowed or switch bad.if all is good have vechicle code scan because cruise control control by PCM and vechicle speed sensor and thottle actuator control motor.

Apr 17, 2013 | 2004 Chevrolet TrailBlazer

1 Answer

2005 VW GTI cruise not working


a cruise control is controlled by several items. a switch on the brake pedal (adjustment) switch on the clutch (if you have 0ne) tailshaft speed sensor against engine rpm and vacumm. IF the road speed is too low for the engine revs it wont' engage. If an efi vehicle the sensor on the tailshaft will not tell the cpu to engauge and without this input it won't

Jan 14, 2013 | 2005 Volkswagen GTI

2 Answers

I own a 2005 GMC Canyon Five CYL and the cruise control stopped working last niight. You push the button and no cruise. I checked the fuse and it is ok I exchanged with another 10AMP and no change still...


Start with the simple and check the fuses and the Stop lamp switch. Check your brake lights, if they're not working, the cruise won't work either. If they're not working, check the fuse for them, if the fuse is fine, then take it into the dealer, there's been a recall issued on the brake switch, so it should get fixed for free.
Cruise Control Disengaged
The powertrain control module (PCM) disengages the cruise control operation based on the signals from the following switches:

* The stop lamp switch
* The TCC brake/cruise release switch
* The clutch release switch, if equipped
* The cruise control On/Off switch

The TCC brake/cruise release switch and the stop lamp switch are mounted on the brake pedal bracket. When the brake pedal is applied, the normally closed TCC brake/cruise release switch opens and the normally open stop lamp switch closes. The PCM detects a low signal voltage on the TCC brake/cruise release switch signal circuit and a high signal voltage on the stop lamp switch signal circuit. When the clutch pedal is applied, the normally closed clutch release switch opens and the PCM detects zero voltage on the CCP switch signal circuit. The vehicle speed stored in the memory of the PCM will be erased when the cruise control On/Off button is turned OFF, or the ignition switch is turned OFF.

The Cruise Control System will disengage when the PCM detects that a driver override function has been active for approximately 60 seconds .

When the Cruise Control System is disengaged, the PCM sends a class 2 message to the instrument panel cluster (IPC) in order to deactivate the cruise control indicator.

Cruise Control Inhibited
The powertrain control module (PCM) inhibits the cruise control operation when any of the following conditions exist:

* A cruise control related DTC has been set.
* The vehicle speed is less than 40.2 km/h (25 mph) .
* The vehicle is in PARK, REVERSE, NEUTRAL, or 1st gear.
* The engine RPM is too low.
* The engine RPM is too high, with fuel cut off.
* The vehicle speed is too high, with fuel cut off.
* The system voltage is not between 9 volts and 16 volts .
* The Traction Control System (TCS) is active for more than 2 seconds .

Thank you for using Fixya and start with replacing the stop lamp switch. Even though the brake light work, it;s been known for that switch to cause your issue. that's way there was a recall for it.

Apr 01, 2010 | 2005 GMC Canyon

1 Answer

Cruise control stopped working


Check the switch, located on the brake pedel the stop light switch and the cruise control switch are on the brake pedel towards firewall. The cruise control switch is plastic.

Mar 25, 2010 | 2001 Ford F350 Super Duty SuperCab

2 Answers

97' Ford 350 diesel the cruise control quit


There is a brake light switch that ,disconnects the cruise control,when braking,this maybe the problem,even if the brake lights work fine,the switch still could cause this problem,replace the brake light switch.

Feb 26, 2010 | Ford F-350 Cars & Trucks

1 Answer

Cruise control


sounds like the brake switch is bad as ive seen this a few times

Aug 19, 2009 | 2005 Kia Sorento

2 Answers

Vauxhall Vectra Cruise control problem


try lifting the brake pedal with your toes then switching on the cc when driving. sometimes a faulty or loose switch on the brake pedal can cause cc to cut out.

Jul 08, 2009 | 2004 GMC Sierra 2500

1 Answer

Cruise control does not stay on after setting it.


Possibly a brake or clutch pedal switch fault. Both the clutch and brake pedal have switches to control various things like cruise.

May 22, 2009 | 2005 Kia Sorento

Not finding what you are looking for?
Cars & Trucks Logo

94 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

yadayada
yadayada

Level 3 Expert

75051 Answers

Freddy

Level 3 Expert

1311 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...