Why won't the DIC dispay, alarm stop ringing.

Hi there is a sensor in seat belt it is my bee sticky
hope it help

REMOVE THE DIC CENTER SEE IF IT IS GETTING POWER.SHAKE WIRES SEE IF DIC CONTROL WILL LIGHT UP WITH IGNITION ON ENGINE OFF.IF POWER GOING TO DIC CENTER AND SHAKE WIRES YOU STILL DONT SEE THE OIL DISPLAY LIGHT UP.DIC CONTROL COULD BE FAULTY.

Check the belt latch,(the short belt you click in and push button to release). It has a sensor in it. Tap and shake it as it may have a foreign object in it. Look under the seat for the connector(s), and make sure they are pushed in all the way and that the wires aren't damaged. If that doesn't help, try disconnecting the connector. If the light and alarm are still on afterwards.....you have two choices. First, replace that part of the belt. Or, try running a jumper wire across the two contacts in the connector but I cant tell you that!!

You may want to check the fuse...DIC/RKE located in the fuse panel.

{: ) The PARK ASSIST OFF message will be displayed when the parking assist system is disabled due to conditions that disable or inhibit the system. The object alarm module requests the DIC display PARK ASSIST OFF when it detects one of the following conditions:
• The parking assist system is manually disabled using the driver information center (DIC). • An object is attached to the rear of the vehicle, such as a trailer, bicycle rack, trailer hitch receiver, or tow bar. • The object alarm sensors are covered by snow, mud, dirt, slush, or ice. • The vehicle bumper is damaged. • Excessive paint thickness on a replacement object alarm sensor. • The object alarm sensors are disrupted by vibrations, like those caused by a large nearby vehicle or from heavy equipment such as a jackhammer.
The SERVICE PARK ASSIST message will be displayed when the object alarm module detects a malfunction in the parking assist system and the system is disabled. It could be one of your sensors is at fault or even the module.

{: ) The driver information center (DIC) displays SERVICE PARK ASSIST when the object alarm module detects a malfunction in the parking assist system and the system is disabled. The DIC also displays SERVICE PARK ASSIST when a loss of communication occurs with the object alarm module. Usually this is caused by faulty components or wirings. Better visit your dealer if still under warranty, for one park assist sensor only costs too much. If your bumper had been knocked off or had previous repairs outside the dealership, that's another thing.
The PARK ASSIST OFF message is displayed in the DIC when the parking assist system is disabled due to conditions that disable or inhibit the system. The object alarm module requests the DIC display PARK ASSIST OFF when it detects one of the following conditions:
• The parking assist system is manually disabled using the driver information center (DIC). • An object is attached to the rear of the vehicle, such as a trailer, bicycle rack, trailer hitch receiver, or tow bar. • The object alarm sensors are covered by snow, mud, dirt, slush, or ice. • The vehicle bumper is damaged, • Excessive paint thickness on a replacement object alarm sensor. • The object alarm sensors are disrupted by vibrations, like those caused by a large nearby vehicle or from heavy equipment such as a jackhammer.

{: ) SERVICE PARK ASSIST The driver information center (DIC) displays SERVICE PARK ASSIST when the park assist module detects a malfunction in the object detection system and sends a request to the DIC for display of the message. The DIC also displays SERVICE PARK ASSIST when there is a loss of communication with the park assist module.
PARK ASSIST OFF The PARK ASSIST OFF message is displayed in the DIC when the park assist system is disabled due to conditions that disable or inhibit the system. The red LED in the rear display, as well as, the telltale in the switch will be lit, notifying the driver the PARK ASSIST system is disabled. The object alarm module requests the DIC via the serial data circuit to display PARK ASSIST OFF when it detects that one of the following conditions is true:
• The object alarm system is disabled through DIC vehicle customization feature. Refer to the Owners Manual for more information. • An object is attached to the rear of the vehicle, such as a trailer, bicycle rack, or hitch receiver. • An object is hanging out of the endgate. • The park brake is not fully released. • The system receives vibrations from a large nearby vehicle or from a heavy equipment such as a jackhammer. In the case of objects attached to the rear of the vehicle such as a trailer, hitch receiver, or a bicycle rack, or objects hanging out of the endgate, the rear parking assist (RPA) will have an Automatic Object induced disable feature where the RPA will determine if the rear object is moving with the vehicle. If the RPA detects such a condition, the park assist will be disabled. The PARK ASSIST OFF message will continue to be displayed until the trailer hitch receiver is removed and the vehicle is driven forward above 24 km/h (15 mph).

There is a fault code present and you will have to take it to a dealership for them to use a Tech II and read the code.

find the fuse for the alarm and pull it out tha=is should solve it, but means you have no alarm

try pushing down lightly on the parking brake and release it. you have pushed it down some and the parking brake is on