Question about 1998 Ford Ranger SuperCab

Open Question

Where on motor is egr vavle for 98 ford 4.6l - 1998 Ford Ranger SuperCab

Posted by Anonymous on


3 Suggested Answers

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017

  • 1114 Answers

SOURCE: 2001 ford escape does not want to go over 60 mph

change the converters and be done with it before you cause severe damage to mortar!

Posted on Jan 08, 2009

  • 1 Answer

SOURCE: where is the egr vavle located on a ford 2004 expolorer

Here's a pic of it on a 2004 Explorer Sport Trac. It's the part on the right of the 4.0L SOHC cover. It's a coppery color. Held on by two small bolts and then you'll need a big wrench to break the exhaust pipe part of it loose. Be careful. Those can brake. Spray some WD40 on it before you break it loose.

Posted on Sep 17, 2012

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

I have a 2002 ford ranger 2.3l and it has code po403 i beleave it needs a egr vavle but not sure how to change it it looks like its in a really hard place to get to

It's not a bad EGR valve ! It's a electrical problem ! P0403 Ford Exhaust Gas Recirculation Control Circuit Suggest you take your vehicle to a qualified repair shop before you replace parts you don't need >

Nov 16, 2016 | Ford Ranger Cars & Trucks

2 Answers

I need to know what the problem the p0401 what is the problem 1999 grand Victoria Ford 4.9

wow I wish ford could make a egr system that wouldn't fail as I've seen this one go a lot lately ! anyways the code is for insufficient flow in the egr system , this is a means to recirculate some of your exhaust back into your intake , as a means to reburn some of your excess fuel (emissions) , anyways it consists of a means to meter some of the exhaust , and control it (off/on) also to measure the amount that goes in , its part of the closed loop of the fuel inlet system , the fault code is specifically saying flow sensor cant detect any flow in the pipe , there can be a few causes for this including a bad flow sensor , all are from my opinion a poorly designed system (it doesn't self clean it's self ) as almost a guaranty every 60k miles your gonna have some problem with it

Feb 03, 2016 | Ford Cars & Trucks

1 Answer

Pollution vavle

You must be talking about the EGR valve.You didn't state your vehicle 's engine size and I am elected to do that,so we are using the 98 year.Here's a link to what it looks like,easy to remove,just disconnect vacuum hose,remove 2 bolts holding it on,it has a gasket on it,may need replacing if you remove.

Jun 07, 2013 | Ford Crown Victoria Cars & Trucks

1 Answer

I have a 99 Windstar 3.8L Keep getting DTC PO401 have replaced DPFE EGR Valve and EGR tube still keep getting Code PO401

Does the egr vavle open ? You will need to use a scanner to test the dpfe voltage when the egr valve is energized you should read around 3.5 4.00 volts. Also you could remove the vacume line from the egr valve and with the engine running you should see around 100 rpm drop in engine rpm at least this would indicate the egr valve is capable of flowing egr gases through the system to the cylinders.

May 30, 2010 | 1999 Ford Windstar

1 Answer


The mechanical components of the egr themselves may be fine, but the electrical circuit that moves the egr may be faulty. now if the egr valve uses vaccum to operate, then it may be sticking just enough to throw a code.

Feb 11, 2010 | 2001 Mitsubishi Galant

1 Answer

How do i replace iac valve on 2001 ford escape

The IAC vavle is located behind the EGR valve on the driver side of the motor. You will disconnect 2 hoses and unplug the wire harness from the system. The unit will come right out. Just make sure that the hoses you take off go back in the same place. Also make sure that you have the negative battery wire disconnected. I had this same issue on my 2001 Escape, had to replace both the EGR and IAC so check both carefully.

Jan 03, 2010 | 2002 Ford Escape

1 Answer

1989 ford f150 302fi will start and run but will stall out at various times.usually will start again but dies

Have you replaced fuel pump? It could be one of 3 things- fuel pump, tune up or EGR vavle and sensor.

Sep 18, 2009 | Ford F-150 Cars & Trucks

1 Answer

2001 ford escape does not want to go over 60 mph

change the converters and be done with it before you cause severe damage to mortar!

Jan 08, 2009 | 2001 Ford Escape

1 Answer

Won't idel

can seafoam clean carbon from the egr vavle for the gas and motor let ur car man clean the egr valve run some stuff in it motor getting carbon due to sitting and sends it through ur egr

Dec 23, 2008 | 1994 Chevrolet S-10

Not finding what you are looking for?
1998 Ford Ranger SuperCab Logo

Related Topics:

40 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts


Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers


Level 3 Expert

5546 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides