Question about 2002 Ford E350

1 Answer

2002 ford e-350 dually cargo van can not remove rear rotors

I have a dually 2002 ford e-350 dually wheels. the rear axel broke. took the tires off. took the axel spindal screws out but the rotor does not come off. it slides about 1/2 inch and everything looks clear. but feels like something is touching inside and not letting it come off. any ideas???

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 64 Answers

It's hammer time!

Posted on Jun 23, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Axel for 2002 kia rio


You should make the front end repairs and then get new tires. An alignment won't help until you replace the bad parts.

Sep 11, 2013 | Kia Cars & Trucks

1 Answer

How to remove wheel cylender from a 1987 , ford ecoiline , 350 , dually , rear , 7.5 l.


LOOK ON BRAKE SHOE BACKING PLATE WHEEL CYLINDER HAS 2 SCREWS HOLDING IT IN PLACE.

Sep 16, 2011 | Ford Econoline Cars & Trucks

1 Answer

I need to replce my rotor's on an e-250 van. How do I remove them?


Place van in park and place chocks behind the rear wheels. Jack up the van and place two jack stands underneath the frame. Remove the front tires. Loosen the bolts holding the caliper assemblies and use a large flat screwdriver to pull the caliper 1/16 in. Remove the bolts holding the calipers and pads and set the assembly up out of the way. Do not put any strain on the brake lines. Take off the bearing caps. Remove the cotter pins and wheel bearing nuts. Pull the rotors off. Inspect and have them machined or replace them with new.

Mar 25, 2011 | Ford E-250 Cars & Trucks

1 Answer

How do you replace front hub assembly on 2002 explorer 4 wheel drive


remove the wheel, and brake rotor as well as the calipur. behind the hub where the axel goes in, there will be some bolts , remove them, and then push the axel back in it as far as it will go, then pry or hammer it off the spindle , reverse to install.

Dec 30, 2010 | 2002 Ford Explorer

1 Answer

How to replace rear breaks on 2005 f350 super duty dually


Rear To Remove:
  1. Remove the brake master cylinder filler cap and remove fluid until the reservoir is half full.
  2. Raise and safely support the vehicle.
  3. Remove the rear wheel and tire assembly. CAUTION
    Never allow the brake caliper to hang from the brake hose.
  4. Remove the two disc brake caliper pin bolts.
  5. Lift the disc brake caliper from the anchor plate and position the caliper out of the way. Do not disconnect the fluid line.
  6. Inspect the disc brake caliper for leaks and replace the caliper if necessary.
  7. Remove the pads and retraction clips.
To Install:
CAUTION
Do not allow grease, oil, brake fluid or other contaminants to contact the pad lining material.
  1. Install retraction clips.
  2. Install the brake pads.
  3. Slowly compress the caliper pistons with a large C-clamp. CAUTION
    Use care not to damage the bleeder screw or front disc brake rotor shield.
  4. Install the disc brake caliper.
  5. Install the disc brake caliper pin bolts. Tighten the pin bolts to 26 ft. lbs. (35 Nm) (F-250, F-350 SRW). Tighten the pin bolts to 56 ft. lbs. (76 Nm) (F-350 DRW). Tighten the pin bolts to 46 ft. lbs. (62 Nm) (F-450 F-550).
  6. Install the wheel and tire assembly.
  7. Lower the vehicle.
  8. Fill the brake master cylinder reservoir with DOT 3 motor vehicle brake fluid.
  9. Inspect for correct brake operation.

Jul 06, 2010 | 2005 Ford F 350 Super Duty

2 Answers

Frontend shakes when braking, sometimes - have


The actual disc rotors have warped with heat (eg, driving with foot lightly on brake pedal). Easy fix, take it to a brake shop and get them to true the rotors. In New Zealand, we have guys that come to you to do it but essentially, they use a lathe and trim disc provided it doesn't go below manufacturers specs for thickness.

Oct 13, 2009 | 2002 Ford E-Series

1 Answer

Removing rear rotors on 2002 dodge dually.


Remove the axle and outer wheel bearing and pull the assembly off the truck. The rotor is bolted on from the rear.

Apr 17, 2009 | 1997 Dodge Ram 1500 Club Cab

Not finding what you are looking for?
2002 Ford E350 Logo

Related Topics:

532 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

fordexpert

Level 3 Expert

5546 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...