Question about 2005 Hyundai Getz 1.6

Open Question

How to replace fascia panel on a 2005 Getz

To replace bulbs in panel for the heater lights

Posted by Anonymous on

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

3 Answers

One high beam not working 2006 Buick lacrosse


Sampson, sounds like a bunt out bulb, which will need changed.
If you feel comfortable doing it yourself. Basically three screws, and you have to pull one plastic fastener from the fascia (bumper) and pull the bumper back a bit, and pull the assembly out. I believe it is in the manual, not bad to do. I will post a link to tell or show you how to do it. Press the helpful button

Headlight Change 2005 2009 Buick LaCrosse 2006 Buick LaCrosse CX 3 8L V6

2008 Buick LaCrosse Headlight Replacement

Thread how do replace the headlight bulb in 2005 buick lacrosse

Headlight Bulbs

Feb 13, 2016 | Buick Cars & Trucks

1 Answer

How to change stop light globe on 2008 hyundai getz


Remove the two 10 mm (head) bolts that hold the stop light. This bolts are between the tail light assembly and the tail gate weatherstrip. You can see them without having to remove anything.

By using a masking tape wrapped flat screwdriver, pry "back" the whole tail light assembly. Once out, you can twist the brake light (or reverse, or turn signal) bulb plug, remove and replace the bulb.

The Getz uses standard two filament brake globes (1/4 turn to install).

May 12, 2014 | 2008 Hyundai Getz 1.6

1 Answer

Steam comes out of the air vents Hyundai getz


Sounds like the heater matrix has been damaged. Turn the heater to cold to see if still happen. If it stops, took under bonnet/hood to see if its coming out in engine bay.....

Apr 07, 2014 | 2005 Hyundai Getz 1.6

1 Answer

How to replace rear brake light hyundai getz 2004


Access to the tail light cluster should be through panels in the rear corners of the vehicle. Remove the panel and you can remove the tail light cluster to replace the bulbs. This is the position on most sedans, unless, like on pick-ups, the tail light lenses have screws which allow the lenses to be removed to change the bulbs.

May 15, 2011 | Hyundai Motor 2004 Accent

1 Answer

Need to replace the headlight assembly on front passenger side do i have to take off the bumper? for ponitac vibe 2003 also have dent on the area


Yes you do. This is the steps to do that to replace the entire headlight assembly:


Remove the front fascia.
  • Remove the front fascia extensions, if equipped.
  • Remove the front fender liners.
  • Remove the fog lamps.
  • Remove the bolts (4) from the front bumper fascia (3) at the fender.


506bafd.gif

Remove the bolts from the front bumper fascia at the fender



  • Remove the push-in retainers (2) from the bumper fascia using J38778.
  • Remove the fascia bolts (1) from the fascia.
  • Remove the fascia from the vehicle.
  • Remove the 3 bolts which secure the composite headlamp.


  • 7f1ec16.gif

    Remove the 3 bolts which secure the composite headlamp



    1. Remove the sidemarker bulb electrical connector.
    2. Remove the sidemarker bulb, if necessary.
    3. Remove the composite headlamp assembly from vehicle.

    To install:

    1. Install the sidemarker bulb to the composite headlamp, if removed.
    2. Connect the sidemarker bulb electrical connector.
    3. Secure the composite headlamp to the vehicle with the 3 bolts. Tighten the headlamp mounting bolts to 89 inch lbs. (10 Nm).
    4. Install the front fascia.
    5. Install the headlamp bulb to the composite headlamp, if removed.
    6. Fasten the headlamp bulb retainer clip.
    7. Install the socket to the headlamp bulb.
    8. Install the rubber cover to the composite headlamp.
    9. Aim the headlamps.
    10. Close the hood.

    Oct 12, 2010 | 2003 Pontiac Vibe

    1 Answer

    How do I replace dashboard heater light? The glowing lights that indicate direction of air flow.


    Heater light bulb, and all other bulbs for the air conditioning buttons, are on the same mini panel, and attached to the back of the radio front fascia. To dismount this fascia, you need 1) To pry out (no screws) the clock 2) Unscrew the one screw that holds the top of the fascia (screw is hidden behind clock) 3) Unscrew the two screws at the bottom of the fascia 4) Disconnect all connectors from the back of the fascia 5) Look for the burnt minibulb.
    You could replace the bulb without disconnecting, but the cables are short, and the possibilities of marring your dashboard are high.

    Jun 19, 2010 | 1999 Honda Accord

    1 Answer

    How to change 2005 Corvette fog light bulb


    Fog lights are simple, but tight as you would expect.

    You will need to jack up the front.

    Remove the front fascia closeout panel and right and left lower cowl/spoiler.

    Un plug the electrical to the back of the foglight, reach up in and unscrew the bulb. A bit tight. It is about a half or three quarter turn. Pull the old bulbs out.

    Install in reverse.

    You may need to adjust the beam if you tug to much.

    Once you remove the access panel and then pull the brake cooling duct out of the way (just snaps in place...).

    It was not necessary to remove the small air-dam corners on my car (nor is it specified in the service manual), but it it make the job easier, it is only two or three screws per side.

    Thank you for suing fixya and be safe

    Apr 18, 2010 | 2005 Chevrolet Corvette

    1 Answer

    How do you remove the air filter box on a 2001


    REMOVAL
    Release hood latch and open hood.
    Access Rubber Grommet
    Remove large rubber grommet (70 mm x 168 mm) from splash shield to gain access to fascia fasteners.
    Fastener Locations

    Remove fasteners attaching fascia to the front fender and splash shield, using access hole in splash shield.
    Remove Push In Fasteners
    Remove the push pins attaching the fascia to the upper radiator closure panel.
    Headlamp Jack screws

    Remove jackscrews attaching headlamp housing to crossmember and remove the lamp housing to access the lamp(s).
    Roll Fascia Forward

    Roll fascia forward to clear way for headlamp housing removal.
    Disconnect wire connector from back of lamp socket(s) and/or bulbs.
    Remove Headlamp Housing

    INSTALLATION
    CAUTION : Do not touch the glass of halogen bulbs with fingers or other possibly oily surface, reduced bulb life will result.

    Place headlamp housing into position.
    Connect wire connector to lamp socket(s)
    Verify headlamp and signal lamp operation.
    Install jackscrews to attach headlamp housing to crossmember.
    Align fascia to bumper reinforcement and install the top center push pins, to upper radiator closure panel.
    Align the two fascia studs to the fender vertical attachments, at the same time align the fascia groove on the horizontal flange with the fender drive pin. Push fascia rearward to engage the fasteners.
    Install nut on fascia stud through the splash shield access hole.
    Verify headlamp operation and alignment


    Nov 03, 2009 | 2001 Chrysler 300M

    1 Answer

    How do you replace headlamp bulbs on 1999 chrysler 300


    You half to remove the Headlamp housing to change it. Here is the instructions out of the factory manual.
    Tell me if this works for you?
    HEADLAMP HOUSING - CONCORDE/LHS/330M Headlamp lens fogging is a normal condition and does not require service unless excessive or continual. Moisture will vent from tubes or vents located on the back of the lamp.
    REMOVAL
    1. Release hood latch and open hood.
    2. Remove large rubber grommet (70 mm x 168 mm) from splash shield to gain access to fascia fasteners Access Rubber Grommet
    3. Remove fasteners attaching fascia to the front fender and splash shield, using access hole in splash shield Fastener Locations
    4. Remove the push pins attaching the fascia to the upper radiator closure panel Remove Push In Fasteners
    5. Remove jackscrews attaching headlamp housing to crossmember and remove the lamp housing to access the lamp(s) Headlamp Jackscrews
    6. Roll fascia forward to clear way for headlamp housing removal Roll Fascia Forward
    7. Disconnect wire connector from back of lamp socket(s) and/or bulbs.
    8. Remove headlamp housing Remove Headlamp Housing
    INSTALLATION CAUTION: Do not touch the glass of halogen bulbs with fingers or other possibly oily surface, reduced bulb life will result.
    1. Place headlamp housing into position.
    2. Connect wire connector to lamp socket(s) and/or bulbs.
    3. Verify headlamp and signal lamp operation.
    4. Install jackscrews to attach headlamp housing to crossmember.
    5. Align fascia to bumper reinforcement and install the top center push pins, to upper radiator closure panel.
    6. Align the two fascia studs to the fender vertical attachments, at the same time align the fascia groove on the horizontal flange with the fender drive pin. Push fascia rearward to engage the fasteners.
    7. Install nut on fascia stud through the splash shield access hole.
    8. Verify headlamp operation and alignment

    Mar 27, 2009 | 1999 Chrysler 300M

    1 Answer

    Instrument panel lights


    i just recently replaced mine and the temp control had burned . the dash fascia needs to be removed. the vents must come out and then remove the screws that hold it on..there are probably 10 screws.. under the vents , behind the ashtray, and behind the cruise control switch and dimmer switch.. once this is done you need to remove the 4 screws that hold the heater control unit in. the bulb that needs to be replaced lights up temp control and fan speed...you may be able to download an exploded veiw of the dash fascia...this is an involved job...but worth it at night!

    Oct 17, 2008 | 1992 Honda Accord

    Not finding what you are looking for?
    2005 Hyundai Getz 1.6 Logo

    Related Topics:

    31 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Hyundai Experts

    yadayada
    yadayada

    Level 3 Expert

    75807 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22133 Answers

    Jeff Turcotte
    Jeff Turcotte

    Level 3 Expert

    8172 Answers

    Are you a Hyundai Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...