Question about 2004 Chrysler Sebring

1 Answer

How do i change from manual seats to power seats and will the car have the wiring clip?

I want to switch from manual seats to power seats and I would like to know if the car comes with the clip where I can just plug in the seat or if I have to run the wires to the fuse box. Thank you

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 112 Answers

I expect your best option is the wrecking yard for the power equipment and switch gear. Wiring is easy-- just add a new circuit!

Posted on May 24, 2014

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 744 Answers

SOURCE: 2.7 l misfire after changing plugs

From karjunkie:

If the plugs get wet, then you have a spark problem somewhere in the ignition system. Pull a spark plug and hold it against a ground while you turn the engine over. You need to see a fat blue spark. If not, check the distributor, spark plug wires and coils. An easy way to test for spark is with an inexpensive spark tester. This is a device that is readily available at most auto supply stores. If the plugs do not fire properly, check the spark plug wires for fraying or cracking. Next, you need to check the coil(s). If firing voltage is low (weak spark), measure the coil primary and secondary resistance with an ohmmeter. If it is out of specifications, replace the coil. Also, make sure the coil is receiving normal voltage from the PCM or ignition module. If it is low, check the charging system for anything that may be reducing alternator output (battery and alternator cable connections, ground connections and voltage output).

Posted on Mar 22, 2009

motor1258
  • 6674 Answers

SOURCE: 2003 Chrysler sebring wiring diagram for power and heated seats

Do some checking if you haven't already, the harness may already be there under carpet. If not, you may have to sweet talk a service guy at dealership for the print you need, or try www.alldata.com.

Posted on Mar 27, 2009

  • 1 Answer

SOURCE: driver side power seat front to back motor stuck forward

Take apart the drive box in front of seat track, on both sides with an allen wrench. You can then push the seat to get at the bolts to remove it. My trolley drive motor had bad brushes. I am now looking to replace the motor, if I can find the replacement.

Posted on May 04, 2009

polarcycle
  • 1392 Answers

SOURCE: driver seat won't move

Look in the fuse box under the hood. Check for power and ground at the switch. Possibly a body control module problem also. Have seen a few switches go bad, but not all functions.

Posted on Jun 10, 2009

  • 1071 Answers

SOURCE: 2000 Chrysler Town & Country - Heated Seat Wont Heat

the actuator could be bad check ground wires check for power to the fuse and the device

Posted on Aug 26, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Ford expedition power seat not working up/down nor move forward/ backwards and the seatbelt light indicator is on,please help.


get it serviced, the magic is gone.
complex seat parts.
or read the FSM on all those complex tests.
factory service manual, on topic, seats.

ask ford to fix it or buy the book, or get it serviced anywhere;.

Jan 10, 2015 | Ford Cars & Trucks

2 Answers

Electric driver seat not working. And mirror's. In insignia


CHECK FUSES..... MAKE SURE VOLTAGE IS GETTING TO THE MOTORS AND SWITCHES FOR THE SEAT...IF SO.... YOUR SEAT MOTOR MAY BE OUT... AND THE MIRROR MAY BE ON THE SAME CIRCUIT. IF ONE QUITS THEY BOTH QUIT. WHICH IS OBTUSE, BECAUSE THEY SHOULD HAVE BEEN WIRED IN PARALLEL AND NOT SERIES.

Jan 06, 2015 | Cars & Trucks

2 Answers

How to change manual seats to power seats


Check this link for information..

Keep in mind you will have to run power and control wires to the new power seat. Also you will have to find a passenger door switch

May 17, 2014 | 2004 Chrysler Sebring

1 Answer

I need help on removing door panel on 2000 Dodge Caravan - window fell in dorr and I can not seem to get the panel off. Any suggestions?


Answer
FRONT DOOR TRIM PANEL
REMOVAL
Using a trim stick (available from parts stores), pry courtesy lamp from door trim.
Disconnect wire connector from courtesy lamp.
If equipped, remove screws attaching door assist handle to inner door panel.
If equipped, remove screw attaching door pull cup to inner door panel.
If equipped, remove screws attaching trim panel to door from below map pocket.
If equipped, remove window crank.
Using a trim stick, remove screw cover from switch panel.
Remove screws attaching switch panel to door trim.
Remove power accessary switch from door trim Front Door Switch Panel
Disconnect power switch from wire connector.
If equipped, using a small, flat bladed pry tool, remove memory seat/mirror switch and disconnect wire connector Memory Seat/Mirror Switch
If equipped, remove screw holding door trim to door panel from behind inside latch release handle.
Disengage clips attaching door trim to door frame around perimeter of panel Front Door Trim Panel
Lift trim panel upward to disengage flange from inner belt molding at top of door.
Tilt top of trim panel away from door to gain access to latch linkage.
Disengage clip attaching linkage rod to inside latch release handle Inside Door Handle Linkage
Separate linkage rod from latch handle.
Remove front door trim panel from vehicle.
INSTALLATION
Hold top of trim panel away from door to gain access to latch linkage.
Place linkage rod in position on latch handle.
Engage clip to hold linkage rod to inside latch release handle.
Place front door trim panel in position on door.
Install trim panel into inner belt molding at top of door.
Install clips to attach door trim to door frame around perimeter of panel.
If equipped, install screw to attach door trim to door panel behind inside latch release handle.
If equipped, connect power switch into wire connector.
Place power accessary switch in position on door trim.
Connect wire connector into memory seat/mirror switch and install switch into trim panel.
Install screws to attach accessary switch panel to door trim.
Install screw cover into switch panel.
If equipped, install window crank.
If equipped, install screws to attach trim panel to door inside map pocket.
If equipped, install screw to attach door pull cup to inner door panel.
If equipped, install screws to attach door assist handle to inner door panel.
Connect wire connector into courtesy lamp.
Install lamp in door trim.

Feb 02, 2012 | 2000 Dodge Caravan

1 Answer

Front seat wont move backwards but will move forward.. anyway you can move seat manually because its powered??


you have a bad switch , if you have a junk yard near you just go grab a switch and replace yours, if not,, and you have knowledge of cars ,, you can jumper the switch ,, your going to have a power wire going to the switch, and thats usually the center wire, out of each end of the switch are 2 other wires, ( one for forward, and one for back, if you take off the connector at the switch , and with a meter locate the power wire, ( 12 volts ) then you can use a jumper wire to supply that voltage to the correct wire that makes the seat move, I don't have the wiring color chart for your car, but if you just touch the power end of the jumper, to one or the other of the wires in that connector,, the seat will move,, once you do that ,, put it where you want it, and reconnect the switch and replace the switch when you can

Aug 12, 2011 | 2003 Oldsmobile Bravada

1 Answer

2001 HONDA ACCORD SEATS


Hi:
The leather seats will easily bolt right up, but you need to check and see if your car has the wiring harness for the power seats tucked under the carpet. Often, all cars have the proper harness,but not connected, and the fusebox has no fuse installed either, but it is a good thing to check before you start the project.

Jan 30, 2010 | 2002 Honda CR-V

2 Answers

93 ford tempo v-6 replaced fuel pump but will not start did reset


by chance the replacement pump you used was it a "CARTER" brand I had one of those quit the same day installed it! also be sure that the feed wire on pump in tank is connected properly! you can change them by taking out the back seat of car!! the seat has 2 clips good luck

Dec 22, 2008 | 1993 Ford Tempo

1 Answer

2000 Blazer power seats


i dont thing there is something to do with the power seats when you blew an engine, plus the power locks too.

im thingking, when you put the engine, a lot of wires and fuse boxes are in the engine compartment, you could probably disconnect some wire that are on the way on changing the engine and forgot to put the wires back together.

that is the only thing i could think of..

i hope i answered your questions...

tnx

drcool

pls rate me...

Jul 26, 2008 | 2000 Chevrolet Blazer

Not finding what you are looking for?
2004 Chrysler Sebring Logo

58 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

76070 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8266 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...