Question about 1985 Nissan Pickup

1 Answer

Remove 4x4 transmission

What all to remove to drop the transmission...

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 790 Answers
Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How can I remove the transmission from a 2002 ford escape 4x4, six cylinder?


On a ramp and struggle not for the faint hearted and you will need at least 3 people to drop the box out.

Feb 19, 2016 | Ford Cars & Trucks

1 Answer

Engine removal and instalation for dodge ram 50 4x4 5speed


You need a manual to do this. Lots of info to follow. Quick version is. Drain the oil and coolant. Remove the starter, transmission, converter, engine mounts, electrical plugs,vacuum lines, Fan shroud and fan, (depending on year), intake plenum, and drop the A/C compressor. There is plenty more that needs to come off.

Jun 20, 2015 | Dodge Cars & Trucks

1 Answer

Rear main seal replacement


remove air filter and housing that be in the way.you need long off set flex ratchet wrench.you need off set box end wrenches to remove top transmission bolts.

Jul 10, 2013 | 1993 Ford Explorer Limited

1 Answer

How do i drop the trans


Remove the Rear Drive Shaft
Remove the Transfer case if 4x4
Disconnect the Shift
Disconnect the Clutch Secondary
Floor Jack under the Transmission
Remove the Cross Member
Remove Bell House Bolts
Pull straight Back
Lower Down
6 Pressure Plate Bolts
Remove 6 Flywheel Bolts

*(Recommend replacing Rear Main Seal)

Resurface Flywheel
Reassemble

Apr 15, 2013 | 1991 Ford F250

1 Answer

A cannot get the top center bolt out of the bell housing into the engine block on my 4l60e transmission in my 2001 chevy silverado 4x4


to remove the upper bell housing center bolts on a 4L60E (not an E if it's 4wd by the way but we'll go with that for now)
you will have to unbolt the transmission from the crossmember and drop it down which will in turn tilt your motor back and allow you better access to those two top bolts. Put your two bottom bolts back in finger tight before you drop the transmission down though or you stand the chance of breaking the bell housing when it's tilted back. you can also use a floor jack on your crank pulley on the front of the motor. Jack up on it and the motor will tip back but not if you have the transmission bolted in place still. hope this helps

Feb 22, 2013 | Cars & Trucks

1 Answer

I have a 1987 ford ranger 4x4 and im trying to figure out how to remove the shifter linkage from the tranny to drop the tranny


Hi danielh_04,
There are two different manual transmissions for that year but both processes are about the same. You need to remove the screws from the shifter boot and pull it back to gain access to the top of the transmission through the floor board. You should see a cover with bolts. Remove the bolts and pull the cover off. Then you want to carefully pull up on the shifter. The lever,shim and the bushing should come out. After you get it removed,you can cover the hole with a rag and drop the transmission. Good luck,if you need anything else,let me know,Chuck.

Dec 23, 2009 | 1991 Ford Ranger Supercab

1 Answer

Do you have to drop the transfer case when you change transmissions on a 94 GMC long bed extended cab pickup 4x4 with teh 6.5 turbo desil


no you should not have to drop it. there should be a slip yoke with the shaft leading from the transmission to the transfer case. when you remove that and support the transfer case there will be plenty of room to move the transmssion back away from the engine to remove it

May 10, 2009 | 1994 GMC Sierra

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

30 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

76649 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

726 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...