Question about 1997 Lincoln Mark VIII

Open Question

How do you remove ignition lock cylinder if you lost thr key?

Posted by Anonymous on

Ad

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
c17hydro
  • 2984 Answers

SOURCE: i need to take out old ignition lock cylinder

This is what the tech manual says.....

Ignition Lock/Switch REMOVAL & INSTALLATION

  1. Disconnect the negative battery cable. If equipped with an air bag, wait at least 90 seconds before working on the vehicle. CAUTION
    Some models covered by this manual may be equipped with a Supplemental Restraint System (SRS), which uses an air bag. Whenever working near any of the SRS components, such as the impact sensors, the air bag module, steering column and instrument panel, disable the SRS, as described in Section 6.
  2. Remove the lower steering column cover. Unfasten the ignition switch connector under the instrument panel.
  3. Remove the screws which secure the upper and lower halves of the steering column cover.
  4. Turn the lock cylinder to the ACC position with the ignition key.
  5. Push the lock cylinder stop in with a small, round object (cotter pin, punch, etc.). NOTE: On some vehicles, it may be necessary to remove the steering wheel and combination switch first.
  6. Withdraw the lock cylinder from the lock housing while depressing the stop tab.
  7. To remove the ignition switch, unfasten its securing screws and withdraw the switch from the lock housing. To install:
  8. Align the locking cam with the hole in the ignition switch and insert the switch into the lock housing.
  9. Secure the switch with its screw(s).
  10. Make sure both the lock cylinder and column lock are in the ACC position. Slide the cylinder into the lock housing until the stop tab engages the hole in the lock.
  11. Install the steering column covers and connect the ignition switch wiring.
  12. Connect the negative battery cable.

Posted on Jul 26, 2009

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2007 cadillac dts key stuck in ignition and wont shift out of park


Ignition Lock Cylinder Control Actuator
The vehicle it is equipped with a floor mounted console gear shifter, and has a ignition lock cylinder control actuator system in the steering column as an added safety feature. The ignition lock cylinder control actuator systems purpose is to prevent the steering wheel from being locked when the transmission is in gear and the vehicle may still be moving. The ignition lock cylinder control actuator system consists of the BCM, the lock cylinder relay, and the ignition lock cylinder control actuator. The ignition lock cylinder control actuator contains a pin that is spring loaded out to mechanically prevent the ignition key cylinder from being turned to the lock position when vehicle speed is above 5 mph for 15 seconds and the transmission is not in the Park position. If vehicle power is lost, and/or the transmission is not in the Park position the operator will not be able to turn the ignition key to the lock position and will not be able to remove the ignition key from the column. For situations where the vehicle must be towed, the system can be overridden by pressing a release button that is reached through an access hole located on the under side of the steering column. First, remove the black plug covering the hole.

Aug 09, 2015 | Cadillac Cars & Trucks

3 Answers

Lost key for 1999 Chrysler Cirris.need to replace ignition lock cylinder


take center of steering wheel off,access the star screw through a hole in the wheel to remove mechanism

Jul 23, 2015 | Chrysler Cars & Trucks

1 Answer

Ignition cylinder locked and lost keys how do i replace ignition lock without key


I think a dealer can help you get another key made. If not, you have to drill and break out the lock cylinder until it can be removed. It is a messy job and some of them have a piece of titanium in them to prevent drilling, that is where the breaking part may come into play.

Jun 03, 2014 | 1995 Buick Regal

1 Answer

How to remove the ignition lock on a 1994 Surburban without a key


A key code is stamped on the lock cylinder to aid in replacing lost keys.

Aug 06, 2012 | 1994 GMC Suburban

1 Answer

I need to change out the ignition on my 94 explorer cause my friend im buyin it lost the key so do you know how to get it out without the key?


You need to turn key to ON position and stick pin or paper clip in hole on side to release it so you can pull it out.

Section 11-04B: Steering Column, Ranger/Explorer 1994 Ranger and Explorer Vehicles Workshop Manual
REMOVAL AND INSTALLATION Ignition Switch Lock Cylinder (Without Key) NOTE: The following procedure applies to vehicles where the lock cylinder is inoperative and the lock cylinder cannot be rotated due to a lost or broken ignition key and the key number not known or the lock cylinder cap is damaged and/or broken to the extent that the lock cylinder cannot be rotated.
Removal
  1. Disconnect the battery ground cable . For tilt columns, tilt to the full up position. Remove the steering wheel , steering column locking lever (3B661) , and steering column trim shrouds as described in this section. NOTE: When drilling out the retaining pin, take care not to damage the cast housing.
  1. Punch the lock cylinder retaining pin with a ***** punch (1/8 inch maximum outside diameter). Using a 3.17mm (1/8-inch) diameter drill, drill out the retaining pin going no deeper than 12.7mm (1/2 inch).
  1. Place a chisel at the base of the ignition lock cylinder cap. Using a hammer, strike the chisel with sharp blows to break the cap away from the lock cylinder.
  1. Using a 9.8mm (3/8-inch) diameter drill, drill down the middle of the ignition lock key slot approximately 45mm (1-3/4 inch) until the ignition lock key slot breaks loose from the steering column cover casting. Remove the ignition lock key slot and the drill shavings from the base of the cover cast housing.
  1. Remove the lock cylinder drive gear, bearing retainer and actuator from the casting as described in this section. Thoroughly clean the components in an acceptable cleaning solution. Carefully inspect all components for any damage resulting from the drill operation. If any of the components show signs of damage, they must be replaced. Clean the casting with compressed air to remove any drill shavings or foreign particles and carefully inspect it for damage. If the casting is damaged, replace it with a new one.
Installation
  1. Lubricate the lock cylinder with grease.
  1. Reinstall the lock cylinder drive gear, bearing retainer and actuator. Lubricate with grease before installing.
  1. Turn the lock cylinder to the ON position and depress the lock cylinder housing retaining pin.
  1. Insert the lock cylinder into the lock cylinder housing making sure that the tab at the end of the cylinder aligns with the slot in the steering gear (3504) .
  1. Turn the key to the OFF position. This action will permit the retaining pin to extend into the lock cylinder housing hole.
  1. Using the ignition key, rotate the ignition switch lock cylinder to make sure to correct mechanical operation in all positions.
  1. Connect ignition key warning switch terminal and wire .
  1. Install the upper and lower steering column shrouds as described in this section.
  1. Install the steering wheel as described in this section. NOTE: When the battery is disconnected and reconnected, some abnormal drive symptoms may occur while the powertrain control module relearns its adaptive strategy. The vehicle may need to be driven 10 miles or more to relearn the strategy.
  1. Connect the battery ground cable .
  1. Check for proper start in PARK or NEUTRAL. Also check to make certain that the start circuit cannot be actuated in the DRIVE and REVERSE positions

Apr 06, 2011 | Ford Explorer Cars & Trucks

1 Answer

Trying to get the ignition tumbler unit out of a 1993 Ford Taurus at the junkyard. worked at it most of two days but no luck yet so I must be missing something having never tried this before.


Ignition Lock Cylinder REMOVAL & INSTALLATION Functional Lock The following procedure applies to vehicles that have functional lock cylinders. Such cylinders either have a key available or known key numbers from which a key can be made.
  1. Disconnect the negative battery cable.
  2. Turn the lock cylinder key to the RUN position.
  3. Using a 1?8 in. (3mm) diameter wire pin or a small drift, depress the lock cylinder retaining pin through the access hole in the upper steering column shroud (under the ignition lock cylinder) while pulling out on the lock cylinder. Remove the lock cylinder from the column. Fig. 1: Using the key, turn the ignition lock cylinder to the RUN position, then depress the retaining pin using a wire pin or small drift 86878085.gif
    To install:
  4. Install the lock cylinder by turning it to the RUN position and depressing the retaining pin. Insert the lock cylinder into its housing. Make sure the cylinder is fully seated and aligned in the interlocking washer before turning the key to the OFF position. This will permit the cylinder retaining pin to extend into the cylinder housing.
  5. Rotate the lock cylinder using the lock cylinder key, to ensure correct mechanical operation in all positions.
  6. Connect the negative battery cable.
Non-Functional Lock The following procedure applies to vehicles in which the ignition lock is inoperative and the lock cylinder cannot be rotated due to a lost or broken key, unknown key number or a lock cylinder cap that has been damaged and/or broken to the extent that the lock cylinder cannot be rotated. 1986-90 VEHICLES
  1. Disconnect the negative battery cable.
  2. Remove the steering wheel. For details, please refer to the procedure located earlier in this section.
  3. Remove the two trim shroud halves after removing the three attaching screws.
  4. Disengage the electrical connector from the key warning switch.
  5. Using a 1?8 in. (3mm) diameter drill, carefully drill out the retaining pin, being careful not to drill deeper than 1?2 in. (13mm).
  6. Place a suitable chisel at the base of the ignition lock cylinder cap, then, using a suitable hammer, strike the chisel with sharp blows to break the cap away from the lock cylinder.
  7. Using a 3?8 in. (10mm) diameter drill, carefully drill down the middle of the ignition key slot approximately 1 3?4 in. (44mm) until the lock cylinder breaks loose from its breakaway base. Remove the lock cylinder and drill shavings from the lock cylinder housing.
  8. Remove the retainer, washer, ignition switch and actuator. Thoroughly clean all the drill shavings from the casting.
  9. Inspect the lock cylinder housing for damage from the removal operation. To install:
  10. Replace the lock cylinder housing if it was damaged.
  11. Install the actuator and ignition switch.
  12. Install the trim and electrical parts.
  13. Install a new ignition lock cylinder.
  14. Install the steering wheel. For details, please refer to the procedure located earlier in this section.
  15. Connect the negative battery cable.
  16. Check the lock cylinder operation.
1991-95 VEHICLES
  1. Disconnect the negative battery cable.
  2. Remove the steering wheel.
  3. Using locking pliers, twist the cylinder cap until it separates from the lock cylinder.
  4. Using a 3?8 in. (10mm) diameter drill bit, drill down the middle of the ignition lock key slot approximately 1 3?4 in. (44mm) until the lock cylinder releases from its breakaway base. Remove the lock cylinder and drill shavings from the lock cylinder housing.
  5. Remove the retainer, washer, ignition switch and actuator. Thoroughly clean all drill shavings and other foreign materials from the casting.
  6. Inspect the lock cylinder housing for damage from the removal operation. If the housing is damaged, it must be replaced. To install:
  7. Replace the lock cylinder housing, if damaged.
  8. Install the actuator and ignition switch.
  9. Install the trim and electrical parts.
  10. Install the ignition lock cylinder.
  11. Install the steering wheel.
  12. Connect the negative battery cable, then check the lock cylinder operation.
prev.gif next.gif

Nov 05, 2010 | 1993 Ford Taurus

2 Answers

Husband lost key to car and I need to know how I can remove the ignition so it can be replaced


Cirrus, Stratus, Sebring Convertible and Breeze CAUTION
The Supplemental Inflatable Restraint (SIR) system must be disarmed before working around the steering column. Failure to do so may cause accidental deployment of the air bags, resulting in unnecessary SIR system repairs and/or personal injury.
  1. Disarm the air bag system, as described in Scetion 6.
  2. Remove the upper steering column shroud.
  3. Pull down the lower steering column shroud enough to access the lock cylinder retaining tab.
  4. Turn the ignition key to the RUN position.
  5. Insert a small prying tool into the tab access hole and depress the tab. Fig. 1: Depress the retaining tab and remove the lock cylinder 90908g36.gif

  6. Pull the ignition lock cylinder from the steering column. To install:
  7. With the ignition key in the lock cylinder, turn the key to the RUN position. Depress the lock cylinder retaining tab. Fig. 2: The shaft at the end of the ignition lock cylinder lines up to the socket at the end of the lock cylinder housing 90908g37.gif

  8. The shaft at the end of the ignition lock cylinder lines up to the socket at the end of the lock cylinder housing. The socket must be in the RUN position for the socket and lock cylinder to line up.
  9. Line up the lock cylinder to the grooves in the lock cylinder housing. Insert the ignition lock cylinder into the housing until the retaining tab sticks through the opening in the housing.
  10. Lightly pull on the ignition lock to make sure it has engaged the retaining tab.
  11. Turn the key to the OFF position. Remove the ignition key.
  12. Install the steering column covers.
  13. Arm the air bag system, as described in Section 6.
Sebring Coupe and Avenger NOTE: For information on removing/installing the Ignition Lock Cylinder, refer to the Ignition Switch removal and installation procedure, earlier in this section. prev.gif next.gif

Aug 17, 2010 | 1996 Dodge Avenger

3 Answers

How to remove ignition lock cylinder without the key


How to remone 1998 windstar GL (3.8 L) Ignition Locl.

Oct 06, 2009 | 1998 Ford Windstar

1 Answer

THE REMOTE DOOR LOCK ON A 2000 BUICK CENTURY HAS QUITE WORKING. THE FOBS ARE GOOD BUT WON'T OPEN ANYTHING.


The transmitter may have lost programming,
In the event that a transmitter is lost, program the old and the new transmitters into the memory of the remote control door lock receiver. Up to 4 transmitters may be programmed.

IMPORTANT:

  • Once entering this procedure, programming the first transmitter erases all previous transmitters. You must program all transmitters.
  • Program one vehicle at a time. One transmitter could be programmed into other vehicles that are also on program mode in close proximity.
  1. Sit in the driver's seat.
  2. Remove the ignition key from the ignition lock cylinder.
  3. Close all vehicle doors.
  4. Press and hold unlock on the door lock switch.
  5. While holding the door lock switch in the unlock position, insert and remove the ignition key twice. Do not rotate the ignition lock cylinder.
  6. Insert the ignition key a third time leaving the key in the ignition lock cylinder. The ignition must remain in the LOCK position for the rest of the procedure.
  7. Release the door lock switch. You will hear three chimes. This chime feedback indicates that transmitter programming is active.
  8. Press and hold the lock and unlock buttons at the same time on the keyless entry transmitter for 12 seconds . You will hear two chimes. This chime feedback indicates that the transmitter has been programmed successfully.
  9. Repeat step 8 for the rest of the transmitters (for a total of 4 transmitters).
  10. Exit this procedure by removing the ignition key from the ignition lock cylinder.

May 07, 2009 | 2000 Buick Century

2 Answers

Ignition switch in a 1995 ford taurus


Ignition Lock Cylinder
Ford Taurus/Sable 1986-1995 Repair Information grey_line.gif

clearpixel_002.gif clearpixel_002.gif lower_right.gif

clearpixel_002.gif

REMOVAL & INSTALLATION

Functional Lock


The following procedure applies to vehicles that have functional lock cylinders. Such cylinders either have a key available or known key numbers from which a key can be made.
  1. Disconnect the negative battery cable.
  2. Turn the lock cylinder key to the RUN position.
  3. Using a 1/8 in. (3mm) diameter wire pin or a small drift, depress the lock cylinder retaining pin through the access hole in the upper steering column shroud (under the ignition lock cylinder) while pulling out on the lock cylinder. Remove the lock cylinder from the column.

Using the key, turn the ignition lock cylinder to the RUN position, then depress the retaining pin using a wire pin or small drift

To install:
  1. Install the lock cylinder by turning it to the RUN position and depressing the retaining pin. Insert the lock cylinder into its housing. Make sure the cylinder is fully seated and aligned in the interlocking washer before turning the key to the OFF position. This will permit the cylinder retaining pin to extend into the cylinder housing.
  2. Rotate the lock cylinder using the lock cylinder key, to ensure correct mechanical operation in all positions.
  3. Connect the negative battery cable.

Non-Functional Lock
The following procedure applies to vehicles in which the ignition lock is inoperative and the lock cylinder cannot be rotated due to a lost or broken key, unknown key number or a lock cylinder cap that has been damaged and/or broken to the extent that the lock cylinder cannot be rotated.

Jan 27, 2009 | 1995 Ford Taurus

Not finding what you are looking for?
1997 Lincoln Mark VIII Logo

Related Topics:

23 people viewed this question

Ask a Question

Usually answered in minutes!

Top Lincoln Experts

yadayada
yadayada

Level 3 Expert

76132 Answers

fordexpert

Level 3 Expert

5520 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Are you a Lincoln Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...