Question about 1986 Ford F150 SuperCab

Open Question

Where is the oils ending unit located on a 86 ford f150

Posted by Anonymous on

4 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 43 Answers

SOURCE: I can not seem to locate the impact switch for my '86 F150. I've been looking around the fire guard. No luck. Can you help?

Below the heater duct , interior, right hand side

Posted on Apr 15, 2009

bonedivers
  • 1140 Answers

SOURCE: i got a 86 ford f150 5.0 EFI the Red wire on the

best to remove and check all fuses

Posted on Jul 10, 2011

  • 14036 Answers

SOURCE: 1998 FORD F150, OIL PRESSURE DROPPING SENDING UNIT

YEP COULD BE WORN ENGINE BEARINGS OR BAD OIL PUMP.

Posted on Oct 23, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where do I locate the oil sending unit on my 98 Ford F150 5.4 Triton engine?


Screws into the base of the housing just above where the oil filter goes on. You can identify it by the wire going to it.

Feb 28, 2015 | 1998 Ford F150 Regular Cab

2 Answers

Engine knocks after starting and running after 2 minutes.oil guage dropped.let truck sit then started truck again ran for two minutes and started knocking bad.is this the oil pump and where is it located


yes it sounds like it,but check your oil too just to be sure ,your oil pump is in the oil pan take off oil pan u should see it,it will be on the sump end of the pan(caution) the oil pump on most vehicles are connected to the distributor so u might have to retime in eng after u do this,Hope this helps and good luck

Apr 05, 2011 | 2004 Ford F150

1 Answer

I have a 99 Ford F150 with a 5.4. It will start and run fine, no codes. After 2 minutes of running the oil pressure goes to zero. Shut off the engine and restart the oil pressure will go up to normal for...


Start by verifying the oil pressure sending unit. It is quite common for a bad sensor to act erratically, such as you have described. Acquire an oil pressure gauge and install it in an appropriate location, perhaps in place of the oil sending unit if a more convenient location is not available, and run the engine. Observe the pressure on the test gauge at various RPM and over a period of several minutes as the engine warms. If pressure on the gauge is good, then you have a problem either with the oil pressure sending unit, in the circuitry, or instrument panel gauge. However, the problem is most likely the sending unit. Note: the sending unit often requires a special socket, which may be obtained at any auto parts store. Also, if you don't own a test gauge or unwilling to purchase, many auto parts stores now rent tools, others even loan tools provided an adequate security deposit is made.

Jun 19, 2010 | 1999 Ford F150 Regular Cab

1 Answer

Replacing an oil pump on a 1991 ford f150


if it's a 2wd it's posible to losen the motor mount's and do it from under the truck, i've doen it on my 86 5.0L but if u have a 4x4 u will have to unbolt the tranny to lift the motor hight enough to get to pomp, it's in the front side of the oil pan

Jun 04, 2010 | 1991 Ford F150

1 Answer

Oil pressure gauge shows no pressure when its cold out for about 5 minutes till it warms up 97 ford f150/4.6l. I use 10w30 oil, could there be a wire connection to the motor be shorting? where is it? Or is...


Jim, I think your oil pressure sender is going bad, you should replace it and see that your oil pressure is in fact good, you can also check and verify the wires to it at the same time. It is located next to the oil filter. Hope this helps, let me know

Dec 09, 2009 | 1997 Ford F150 Regular Cab

2 Answers

Location of the Oil Pressure Sending Unit on a 2001 Ford F-150 V-6 4.2 liter


On the drivers front of engine block below the cylinder head & gasket . Slightly behind waterpump.

Apr 14, 2009 | Ford F-150 Cars & Trucks

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

25 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

fordexpert

Level 3 Expert

5501 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...