Question about 2004 Honda CR-V

1 Answer

Brakes do not completely release at times,

Brakes do not release completely when driving and you have to apply brakes . does this sometimes. also when it has been stopped brakes do not release all the way when you start to drive. only sometimes. what is the problem? no one can tell me whats wrong.

Posted by on


1 Answer

  • Level 1:

    An expert who has achieved level 1.


    An expert that gotĀ 5 achievements.


    An expert whose answer gotĀ voted for 20 times.


    An expert who has answered 20 questions.

  • Contributor
  • 28 Answers

Might be bad brake lines if front (the rubber ones). When they get old they collapse when you apply the brakes and they won't let the brake fluid go back to the master cylinder until the pop back open.

Posted on Jun 24, 2009

  • polkadice Jun 24, 2009

    Might be bad brake lines if front (the rubber ones). When they get old they collapse when you apply the brakes and they won't let the brake fluid go back to the master cylinder until the pop back open.



1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

2 Answers

I bought 03 f-150 7700 series master cylender was replaced just befor i bought it I replaced all 4 disc all pads and calipers when driving brakes lock up

After applying brakes is it all four brakes,check portion valve.if it one check the braided brake line they go bad inside looks fine on outside ,to check jac up the locking brake side have a helper apply the brakes the release spin the wheel if it doesn't release loose bleeder check if it has fluid flow if it releases then replace braided line.

Jun 10, 2017 | Ford F-150 Cars & Trucks

1 Answer

2004 ford lariat it Wont go out of park I

There should be a solenoid that releases when you press the brake pedal. The solenoid releases the lock that prevents you from shifting out of park unless you have applied the brakes.
So, either the brake switch is bad or the solenoid or the wiring.

BUT, sometimes (especially if the car was put into park without coming to a complete stop) the transmission will get a bit stuck - rocking the vehicle could help.

Feb 28, 2015 | Ford Cars & Trucks

1 Answer

Brakes seem to be dragging at times,fuel mileage goes straight to hell and then other times the car rolls right on out.cannot get problem to "happen". i know there is some sort of ******** that...

Hi Wisker, If the brake problem occurs once you have been out on the highway and applied the brakes several times, the problem is with the brake master cylinder and is associated to the seal which should allow brake fluid to return to the pot when the brakes are released. It would seem that your vehicle is building up fluid pressure which is not returning and causing the bakes to apply from that point onward. When the fault reoccurs near home, drive there and open one of the bleed nipples and the brakes should return to normal until they are applied three or four times. The cure is for you to replace the master brake cylinder. Once done bleed the brakes, beginning with the wheel furthest from the reservoir and work closer one wheel at a time untill you complete all four. Make sure the brake fluid is kept topped up all the time and the wheels are chocked so the car cannot move. The Caddy is heavy and you don't want it resting on your chest! regards John

Jun 24, 2012 | 1988 Cadillac Sedan DeVille

1 Answer

While driving the brakes started to slow the car and I pulled off the road and pumped the brakes and it released but now when I apply the brakes they go to the floor but if i apply them hard they work...

You may have three seperate issues. First, could be a brake caliper sticking. Second, the master cylinder is bad.

Finally, Number three...and most likely, your brake pads are worn out, completely.

Have your brakes inspected by a qualified individual. Hope this helps.

Aug 17, 2011 | 2006 Ford Five Hundred

2 Answers

My rigth side front brake is locking the wheel off while driving and the brake is applied

most common cause would be a bad disk brake caliper, or bad brake hose.

the way to find out witch one, is to jack up the front of the car and put it on jack stands. put the transmission in neutral. then turn the front wheels one at a time and wile turning the wheel have some one apply the brake the wheel should stop turning immediately and then wile applying pressure on the wheel have the person in the car release the brake pedal the brake should release immediately if not, then open the brake bleeder on the offending caliper if the brake releases then. you have a bad brake hose if the brake still does not release with the bleeder open then you have a bad brake caliper.


Mar 16, 2011 | 1992 Honda Accord

1 Answer

Brake light flashing on dash, headlights not working without manually turning on and then there is this dinging sound. When I brake the sound completly stops. When I begin to drive again, the noise starts...

sounds like emergency brake is on or the switch is broken try releasing it and see if you maybe hit it if not apply it and release it and see if that fixes your issue good luck

Dec 15, 2010 | 2000 GMC Yukon XL

1 Answer

I have an 03 Chevy tracker 4 cyl 2 wd I've been having problems with the front brakes locking up when driving. It happens at different times and different driving conditions. Sometimes pumping the pedal...

if both front wheels are dragging it is probably the master cylinder, if only one wheel is dragging it could be the caliper or the brake hose, jack the car up and have some one apply the brakes and try to turn the wheel the instant the brake peddle is released both wheels should start turning the instant the peddle is released....hope this helps

Nov 13, 2010 | 2003 Chevrolet Tracker

1 Answer

How do i get my brake caliper to quit sticking and retract properly? I can hear my brake pad rubbing the rotor when I drive and no brake are applied.

If you can hear a squeak from the brake it is an indicator attached to the brake pad to let you know it is time to change pads. If it is not releasing you will generally have a pull to that side when driving. Disc brakes do not move away from the rotor as drum brakes do from the drum. They only apply pressure to the rotor or release pressure but stay in contact with it. The squeak is designed to keep you from running the brakes down to where the rotor would be damaged.

Dec 16, 2009 | 2006 Chrysler Sebring

Not finding what you are looking for?
2004 Honda CR-V Logo

Related Topics:

254 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts


Level 3 Expert

81285 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides