Question about Cars & Trucks

Open Question

Getting oil in the throttle body on a 1996 grand am ,Pontiac 2.4 liter

Posted by Anonymous on

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

ZJLimited
  • 17970 Answers

SOURCE: need wiring diagram for the ecm on a 94 chevy s10

Throttle Position Sensor (TPS) is connected to the throttle shaft on the throttle body. It is a potentiometer with one end connected to 5 volts from the VCM and the other to ground. A third wire is connected to the VCM to measure the voltage from the TPS. As the throttle valve angle is changed (accelerator pedal moved), the output of the TPS also changes. At a closed throttle position, the output of the TPS is low (approximately 0.5 volts). As the throttle valve opens, the output increases so that, at wide-open throttle, the output voltage should be approximately 4.5 volts. By monitoring the output voltage from the TPS, the VCM can determine fuel delivery based on throttle valve angle (driver demand).

zjlimited_1639.jpg

Fig. 1: Common Throttle Position Sensor (TPS) wiring diagram (wire color, terminal identification/location may vary on certain models)


In addition, I send you some wiring diagrams that coud helpful (click image for zoom)...

zjlimited_1640.jpg

Fig. 7: 1996 GM 4.3L Engine Schematic

zjlimited_1641.jpg

Fig. 10: 1996-1997 GM S10/Blazer Chassis Schematic

Hope this helps.

Posted on Jul 28, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is the manifold absolute pressure located on a pontiac grand am 2.4 liter


Right next to the throttle body and down to the right if you are facing the engine from the front. Chances are you have a broken vacuum line. Not often the sensor fails.

Sep 05, 2014 | Pontiac Grand Am Cars & Trucks

1 Answer

Getting oil in the throttle body on a 1996 grand am ,


check the pcv valve or does your car consume oil? engine might experiencing higher amount of combustion blowby due to piston ring wear

May 16, 2014 | Cars & Trucks

1 Answer

I have a 1996 grand am need to know where throttle position sensor is located on car


As the name implies --- screws hold it
on the throttle body

You will have to follow & remove the plastic
air intake ducting, from the air filter to the
throttle on the engine.

We can not know, to the exact inch, where
every one is located on all vehicles

Jun 29, 2011 | 1996 Pontiac Grand Am

1 Answer

Mass air flow sensor location


3.1 liter - It will be in the air snorkel in between the air filter housing and the throttle body.

3.8 liter - it will be mounted in the throttle body right before the throttle.

Both will have a flat 3 wire connector.

Oct 12, 2010 | 1999 Pontiac Grand Prix

1 Answer

Where is the thermostat on a 2004 pontiac grandam 3.4 liter


under the throttle body and is a pain to get to.

Sep 07, 2010 | 2004 Pontiac Grand Am

1 Answer

I am looking to replace my MAP sensor in my 2000 Pontiac grand am se. 2.4 Liter and I need to know the location?


MAP SENSOR LOCATION ON THE THROTTLE BODY.YOU HAVE TO REMOVE THROTTLE BODY MOUNTING SCREWS TO REMOVE.MAP SENSOR WILL HAVE A VACUUM LINE HOOK TO IT.THAT WILL MAKE LOCATING IT EASIER.

Sep 01, 2010 | Pontiac Grand Am Cars & Trucks

1 Answer

Where is the oil presure sending unit in an 1996 pontiac grand am manual 2.4 liters 4 cylynders.


Here's a copy of component locations for various engine sizes for the 1996 Pontiac Grand Am that I had on my online resource.prev.gif next.gif COMPONENT LOCATIONS The component locations shown are typical, and may vary slightly from one model year to another, because of variances in manufacturing and assembly. Fig. 2: 2.0L Engine Component Locations 91064gtt.gif
Fig. 3: 2.3L Engine Component Locations — 1988–90 91064gtu.gif
Fig. 4: 2.3L Engine Component Locations — 1991–93 91064gqa.gif
Fig. 5: 2.3L Engine Component Locations — 1994–95 91064gqb.gif
Fig. 6: 2.5L Engine Component Locations 91064gtw.gif
Fig. 7: 3.1L Engine Component Locations 91064gty.gif
Fig. 8: 3.3L Engine Component Locations 91064gtz.gif
prev.gif next.gif

Aug 29, 2010 | 1996 Pontiac Grand Am

1 Answer

How hard is it to replace thermostat on 3.4 liter pontiac grand am gt


it is a little bit tricky, but certainly do-able. you need to remove the throttle body to gain access to the thermostat housing, so make sure you buy a new throttle body gasket. to take this job on, you will need a few flex sockets and some extensions. make sure you are well equipped before starting this job. good luck!

Jun 14, 2010 | 2000 Pontiac Grand Am GT

1 Answer

Just wondering whats needed to tune up a 1996? thank you richard


Needed are: 1. spark plugs NGK6962 2. spark plug wires NGK8120 3. oil 5W-30 4.2 liters with filter 4. oil filter 5. fuel filter 6. PVC valve 7. throttle body cleaner 8. Grease gun, ( Use Marine Grease ) It cost more but last longer 9. Front, rear, transfer case. 80W-90 10. Antifreeze and thermostat 5.5 liter

Nov 03, 2009 | 1996 Suzuki Sidekick

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

17 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75066 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...