Question about 1990 Chevrolet Suburban

Open Question

Where are screws in front grill of 2000 ford xplr ltd?

Cannot see any screws in front grill to remove

Posted by Anonymous on

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

How to Remove the front grill for Ford Explorer 2003?


You probably can find a video on youtube that will show you how...do a search for it.

Dec 05, 2016 | 2003 Ford Explorer

1 Answer

How change front fender f150 2000


Fender -Front Removal
  1. Remove the radiator grille opening panel reinforcement (8A284).
  1. If equipped, remove the front wheel opening moulding.
    1. Remove the pin-type retainer.
    1. Remove the screws.
    1. Remove the wheel opening moulding.
    sy1~us~en~file=n12124a.gif~gen~ref.gif
  1. Remove the front fender splash shield (16103).
    1. Remove the screws.
    1. Remove the pin-type retainers.
    1. Remove the front fender splash shield.
    sy1~us~en~file=gn2615a.gif~gen~ref.gif
  1. Remove the cowl grille.
  1. On RH front fender, remove the antenna mast.
    sy1~us~en~file=k21762b.gif~gen~ref.gif
  1. On RH front fender, remove the antenna base.
    1. Remove the radio antenna base cap (18A927) by gently inserting a thin straight-edged screwdriver underneath the cap and carefully following inside the perimeter until both snaps are free.
    1. Remove the screws.
    1. Lift the antenna base.
    1. Disconnect the radio antenna lead-in cable (18812) and remove the antenna base.
    sy1~us~en~file=k22299b.gif~gen~ref.gif
  1. Remove the fender stuffer.
  1. Remove the stone guard.
    1. Remove the pin-type retainers.
    1. Remove the stone guard.
    sy1~us~en~file=gn2618a.gif~gen~ref.gif
  1. Remove the front fender.
    • Remove the bolts.

Sep 17, 2014 | 2000 Ford F150 Flareside SuperCab

1 Answer

Need instructions to replace the passenger side mirror and the driver side tail light on a 1999 Ford Taurus 4-door sedan. Thank you, Gary S.


Section 01-09: Mirrors, Rear View 1999 Taurus/Sable Workshop Manual REMOVAL AND INSTALLATION Procedure revision date: 06/25/1998 Mirror, Power-Outside Rear View Removal
  1. Disconnect battery ground cable (14301).
  1. Remove front door trim panel (23942). Refer to Section 01-05.
  1. Remove radio speaker grille from cover assembly by squeezing or pinching between thumb and index finger.
  1. Remove two screws from cover assembly.
  1. Disconnect outside rearview mirror wiring connector (C515-LH; C615-RH). Remove wiring guides as necessary.
  1. Remove three outside rear view mirror retaining nuts. Remove outside rear view mirror (17682) while guiding wiring and connector through hole in door.


an0786b.gif


Item Part Number Description 1 17682 Outside Rear View Mirror 2 N621906-S36 Nut (3 Req'd) 3 F8DB-17D699-
AAW Cover Assembly Rear Substrate-LH 3 F8DB-17D698-
AAW Cover Assembly Rear Substrate-RH 4 N808968 Screw 5 F8DB-18B984-
AAW Speaker Grille-Standard (No Badge)-LH 5 F8DB-18985-
AAW Speaker Grille-Standard (No Badge)-RH 5 F8DB-18K901-
BAW Speaker Grille-Mach-LH 5 F8DB-18978-
BAW Speaker Grille-Mach-RH 5 F8DB-238A35-
AAW Speaker Grille-Blank (No Speaker)-LH 5 F8DB-238A34-
AAW Speaker Grille-Blank (No Speaker)-RH A - Tighten to 6-8 Nm (54-70 lb-in) ------------------
Trim Panel, Door Front
Removal
  1. Remove cover behind inside door handle.
  1. Remove screw from bottom of pull cup retaining front door trim panel to front door (20124).
  1. Remove three screws retaining front door trim panel to front door.
  1. NOTE: Do not attempt to remove more than one pushpin at a time.

    Using Rotunda Windshield and Molding Trim Removal Kit 107-R0401 or equivalent, remove the door trim panel by pulling one door trim panel pushpin at a time from the inner door skin.
  1. Disconnect electrical connectors as necessary. Refer to Section 01-14A.
Installation
  1. Follow removal procedure in reverse order.
  1. Replace all pushpins with new pushpins (N808994-S).
Front Door Trim Panel


ar0318d.gif

Jan 14, 2011 | 1999 Ford Taurus

1 Answer

How do i car door panels safely


  1. Remove the cover behind the inside door handle.
  2. Remove the screw from the bottom of the pull cup retaining the front door trim panel to the front door.
  3. Remove the two screws retaining the sail panel/speaker grille assembly and remove the panel/grille from the door.
  4. Remove the three screws retaining the front door trim panel to the front door.

Do not attempt to remove more than one pushpin at a time.

  1. Use a suitable tool to remove the pushpins from the door.
  2. Carefully lift the door panel away from the door.
  3. Detach the electrical connectors as necessary and remove the panel from the door.

To install:

  1. Installation is the reverse of removal.
Door Panel

This procedure applies to both the front and rear door panels.


// // 0) preLoad.src = ctl00_cphLeft_chRepairTreeNav_tvTOC_ImageArray[i]; } ctl00_cphLeft_chRepairTreeNav_tvTOC_Data.lastIndex = 30; ctl00_cphLeft_chRepairTreeNav_tvTOC_Data.populateLog = theForm.elements['ctl00_cphLeft_chRepairTreeNav_tvTOC_PopulateLog']; ctl00_cphLeft_chRepairTreeNav_tvTOC_Data.treeViewID = 'ctl00$cphLeft$chRepairTreeNav$tvTOC'; ctl00_cphLeft_chRepairTreeNav_tvTOC_Data.name = 'ctl00_cphLeft_chRepairTreeNav_tvTOC_Data'; //]]> var _strTreeScrollHidName = 'ctl00_hidTreeScrollPos'; c17hydro_23.gif

Remove the cover from behind the inside door handle by gently pulling it out to release the retaining tabs


c17hydro_24.gif

Remove the pull cup retaining screw cover and...



c17hydro_25.gif

... remove the retaining screw from the cup and lift the cup straight up out of the door panel



c17hydro_26.gif

Remove the two sail panel/speaker grille retaining screws and...



c17hydro_27.gif

... remove the panel/grille from the door



c17hydro_28.gif

The door panel is retained to the door by 11 retaining clips



c17hydro_29.gif

Carefully lift the door panel off of the door and...



c17hydro_30.gif

... detach the electrical connectors from the switches and remove the panel from the vehicle

Nov 13, 2010 | 1996 Ford Taurus

1 Answer

How do i change the front turn signal in a 2000 expedition


lift the hood, on top of the turn signal housing there is a screw. take out the screw, then you have to pry out the housing- BECAREFUL the housing sits inside the grill ring. take your time

Dec 23, 2009 | 2000 Ford Expedition

2 Answers

2001 ford focus stereo amp location


not all have amps.

SECTION 415-01: Audio Unit 2001 Focus Workshop Manual
REMOVAL AND INSTALLATION Subwoofer Amplifier Removal
  1. Remove the subwoofer speaker. For additional information, refer to Section 415-03 .
8 screws
  1. Remove the grill.
  1. Remove the subwoofer amplifier cover retaining screws.
  1. Disconnect the subwoofer amplifier electrical connectors.
  1. Remove the subwoofer amplifier retaining screws.
    • Remove subwoofer amplifier.

Apr 27, 2009 | 2000 Ford Focus

1 Answer

How to replace 1998 Ford Contour headlights (with diagram)


Step 1
Remove your Contour's front grille. You can do this by raising the hood and removing two screws that are located on top of the grille.

Step 2 Remove the headlight assembly. The headlight assembly is held into the front of your Contour by three screws. Two screws will be located on top of the assembly, and one on the bottom.

Step 3 Replace the headlight assembly, if necessary. If you are only changing individual bulbs, make sure you replace the correct bulbs. Each assembly holds three light bulbs, including the bright, dim and turn signal bulbs.

Step4 Replace the headlight assembly and reattach the three screws to hold it in place.

Step5 Replace the front grille of your Contour and the two screws that hold it onto the front of the car.


  • It is usually a good idea to replace bulbs together (in pairs). This will allow the bulbs to wear at the same rate.
  • If you choose to replace only the individual light bulbs, do not touch the new light bulbs. The contact of your skin on the bulbs will cause the light bulbs to burn out much sooner.

Let me know if you have any further questions.


Benjamin

Apr 26, 2009 | 1998 Ford Contour

1 Answer

The wiper blade connection has released from the wiper blade motor bar that controls the wipers movement. You can hear the motor working but the arms have been disengaged.


please rate as fixya if this is what you need. Mounting Arm and Pivot Shaft —Windshield Wiper Removal
NOTE: The windshield wiper pivot arms (17526) must be in the highest position to remove them.
  1. Turn the ignition switch (11572) to the on position.
  1. Turn the windshield wiper (17500) on.
  1. Stop the windshield wiper pivot arms at the highest position by turning the ignition switch off.
  1. Remove the windshield wiper pivot arm.
    1. Remove the pivot arm nut cover.
    1. Remove the nut.
    1. Remove the windshield wiper pivot arm.

  1. Raise and support the hood (16612).
  1. Remove the cowl grille seal.
NOTE: The two cowl grilles overlap at the center. The LH cowl grille must be removed first.
  1. Remove the LH cowl grille.
    1. Remove the screw cover.
    1. Remove the screws.
    1. Remove the clips.
    1. Remove the pin-type retainer.
    1. Remove the LH cowl grille.
6a042b2.gif
  1. Remove the RH cowl grille.
    1. Remove the screw cover.
    1. Remove the screws.
    1. Remove the clips.
    1. Remove the pin-type retainer.
    1. Remove the RH cowl grille.
bfba69b.gif
  1. Remove the mounting arm and pivot shaft.
    1. Disconnect the electrical connector.
    1. Remove the bolts.
    1. Remove the mounting arm and pivot shaft.
8169c1e.gif

Mar 14, 2009 | 2000 Ford Expedition

2 Answers

Removing Headlight Assembly on 2003 Ford Focus Ultimate Edition


Jack up the front of the vehicle. Secure the vehicle with at least once JACK STAND. Open the hood of the car. Remove the front grill. Remove the fasteners on the head light assembly that are located on the exposed inner fender and the one that was under the front grill. Lay on your back and look between the front fender and the head light assembly. You only have about 4 inches. Remove that screw. All screws are either Phillips or torks.

Dec 24, 2008 | 2003 Ford Focus

Not finding what you are looking for?
1990 Chevrolet Suburban Logo

Related Topics:

15 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75117 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7772 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...