Question about 1999 Chevrolet Venture

1 Answer

How do i change the a/c compressor on 1999 chevy venture

Posted by on


1 Answer

  • Level 1:

    An expert who has achieved level 1.


    An expert that hasĀ over 10 points.


    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 5 Answers

I just completed this task my self, it was not as hard as it looks, disconnect negative battery cable, Jack up the vehicle (Not on the engine cradle) and support with jack stands. Unbolt all the lines and power from compressor, Remove Inner wheel well cover on the passenger side, Remove the serpentine belt. Unbolt front passenger side engine cradle bolt, letting the engine cradle drop in that corner. Remove compressor bolts and remove compressor through the passenger side wheel well. Install in reverse order

Posted on Jul 17, 2009


6 Suggested Answers

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

  • 534 Answers

SOURCE: free pdf download 1999 chevy venture owners manual????

Posted on Feb 03, 2010

  • 2039 Answers

SOURCE: Reset factory alarm 1999 Chevy Venture

passager side lock and unlock the door try it out pierre

Posted on Oct 04, 2008

  • 135 Answers

SOURCE: need to change in my 1999 chevy venture van fuel

look under it on the frame rails, the filter it held to the frame about middle of van ,just follow the fuel lines from tank ,easy to change , ,hope this helps you, thanks robert b.

Posted on Jul 08, 2009

  • 65 Answers

SOURCE: 1999 Chevy Venture Battery Drain Problem!

you have to take out the door ajar switch its in the door it works your interior lights and door ajar switch which is in the door and is hitched to the door latch

Posted on Feb 01, 2010

  • 8197 Answers

SOURCE: how to change rear brakes on 1999 chevy venture


CAUTION Older brake pads or shoes may contain asbestos, which has been determined to be a cancer causing agent. Never clean the brake surfaces with compressed air! Avoid inhaling any dust from any brake surface! When cleaning the brake surfaces, use a commercially available brake cleaning fluid.

  1. Disconnect the negative battery cable.
  2. Remove 2 / 3 of the brake fluid from the master cylinder reservoir using a clean syringe or equivalent. Install the reservoir cap.
  3. Raise and safely support the vehicle with jackstands.
  4. Mark the relationship of the wheel to the hub and bearing assembly.
  5. Remove the tire and wheel assembly.
  6. Remove the caliper, as outlined later, and suspend from the strut with a wire hook or suitable piece of wire. Do NOT disconnect the brake hose or allow the caliper to hang from the brake line!

See Figures 1, 2 and 3

Fig. 1: Properly suspending the caliper, using a wire hook

Remove the outboard shoe and lining (pad) by using a prytool to disengage the buttons on the shoe from the holes in the caliper housing.

Fig. 2: Use a prytool to release the outboard pad retaining buttons

Fig. 3: Remove the outboard brake pad from the caliper

  1. Remove the inboard shoe and lining (pad) from the caliper.

See Figures 4 and 5

Fig. 4: Slide the inboard pad outward, disengaging the retaining clip ears...

2d62026.jpg Fig. 5: and remove the inboard pad from the caliper.

  1. Before installing new pads, clean the outside surface of the caliper boot with denatured alcohol, or equivalent.

To install:
  1. Lubricate the sleeves and bushings with silicone lubricant and install them in the caliper.
  2. One method of pushing the piston back into the bore is to use a large pair of adjustable pliers over the caliper housing and bottom the piston into the caliper bore. Another is to use the special disc brake tool available at most part stores, or even a large C-clamp will work.

See Figures 6, 7 and 8

Posted on Oct 25, 2010

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

My 1999 chevy venture just had a compressor replaced and ac charged. It was working for 3 weeks, and now is blowing warm air??

it may be a slow leak in the system or it may have ait in the lines go under the hood there will be two valves a high and a low side test both and see if you have any freon if so it may be air in the line or even a bad comprssor clutch but not likely

Aug 25, 2011 | 1999 Chevrolet Venture

1 Answer

How do you know what size window you need for a 1999 chevy venture rear (P) window

You dont need to know the size, window go by the year ,make and model and what glass, so you would tell them the same info you just gave me, 1999 chevy venture rear window pass /side,

Jan 11, 2011 | 1999 Chevrolet Venture

1 Answer

99' chevy venture trans "slipping"

change it youll b fine i drive a 99 camaro with 165000 miles on it and i change my tranny fluid every 30000 miles if not comfortable doin that try slick 50 first

May 18, 2010 | 1999 Chevrolet Venture

1 Answer

Reset factory alarm 1999 Chevy Venture

passager side lock and unlock the door try it out pierre

Oct 04, 2008 | 1999 Chevrolet Venture

Not finding what you are looking for?
1999 Chevrolet Venture Logo

736 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts


Level 3 Expert

81342 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides