Question about 2006 Volkswagen New Beetle

Open Question

Selector lever position light display all positions at the same time vw beetle 2006

When place in the drive position all the lights come on on the lever display

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

SOURCE: How to remove head light in a 2006 VW Beetle

go here
http://wiki.answers.com/Q/What_is_the_procedure_for_headlamp_removal_on_a_2006_beetle

Posted on Oct 14, 2008

  • 1 Answer

SOURCE: headlight installation 2006 Beetle TDI

For the 2006 Beetles
FYI - The bulb for the 2006 is DIFFERENT than the 98-05 beetles
GE - H7 55w
I will start with the tools I used:
(Locking mechanism)
1/4” drive ratchet with a 10” extension and a 5mm socket.
(secondary locking mechanism)
wooden paint stir stick (freebie from your local hardware or paint store) or some long thin stick like a wooden dowel.
Passenger’s Side
This is the easiest of the two as there is not as much in your way of both locking mechanisms. If you shine a light towards the front of the bottom of the light housing inside the engine compartment you will see a small silver pin with a 5mm head that has instructions on how to lock/unlock the primary locking mechanism printed on the black plastic above the pin. Using your 5mm socket and long extension. turn the pin ONLY 1/2 a turn and take care as the pin should turn VERY EASILY. Note that the direction to turn this pin is opposite for the passenger and driver's sides. Now the light housing should be able to move slightly out of it’s seat, but it will not come more than about 1” out of the front of the car. You may have to push on the back of the light housing, as VW puts some sticky sealer around the edge of the light housing in the front. A secondary locking mechanism still holds it in place. If you look a little further back, about 3” - 4”, from the primary locking pin; behind a wrapped wire, a/c line, and the power steering resevoir; you will see a horizontal silver lever, about 3” - 4” in length, pointing towards the front of the car. Using your wooden stick, simply hold this lever down about 1” to 2” and pull out the light housing at the same time. The entire housing should freely and easily come completely out of the front of the car. Take care removing it as there are no wires connected to it and it will fall to the floor if you are not holding on to it. Just open the back of the housing and replace the bulb that is out.
Driver’s Side
This is the most difficult one. The battery location is your enemy. In front of the battery, if you look with a flashlight, you will see the primary locking mechanism. It is the only silver looking pin there with a 5mm head. It looks like the headlamp adjusters on other cars. There are instructions printed on the black plastic above it. You should ONLY turn this 1/2 a turn, and you will NOT need to put much effort into turning it as it should turn very easily. You are not done yet. The entire headlamp assembly should be able to pull out of the fender about 1” now, then it will stop as if something else is holding it. You may have to push on the back of the light housing, as VW puts some sticky sealer around the edge of the light housing in the front. There is a secondary locking mechanism that is just a simple metal lever. If you look on the back of the battery, between the air filter housing and the battery, you should see the end of the small shiny silver lever. Using your wooden stick, simply hold this lever down about 1” to 2” and pull out the light housing at the same time. The entire housing should freely and easily come completely out of the front of the car. Take care removing it as there are no wires connected to it and it will fall to the floor if you are not holding on to it. Just open the back of the housing and replace the bulb that is out.

Posted on Dec 06, 2008

  • 65 Answers

SOURCE: lights on buzzer does not work

does your interior light and door light work when the door is open??.the lock mechanism has a micro switch that signifies when the door is open if this dont work niether will the buzzer...its a sound generated by the dash panel insert there is no sepperate buzzer.

Posted on Jan 22, 2009

  • 181 Answers

SOURCE: blue light stays on in my 2000 beetle sometimes flashes

Not certain, but you may be referring to the blue light that indicates when the water temperature in the cooling system is "cold". It's typically blue when the car first starts, then changes color when the water temperature rises. If the light remains blue the water temperature isn't heating up, and you may want to have the cooling system flushed and checked. Depending upon the cars mileage, it may be time to flush the cooling system anyway.

Posted on Jun 22, 2009

  • 1 Answer

SOURCE: 2002 VW Beetle EPC light on

where is the break light switch on a vw bettle

Posted on Dec 26, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My 2006 Ford fusion does not release the key from the ignition when it's in park???


You have a problem with THE SHIFT INTERLOCK SYSTEM !


The floor shifter assembly:




  • locks the transaxle range selector lever in the PARK position when the ignition switch is in the LOCK position.

  • requires the transaxle range selector lever to be in the PARK position to turn the ignition switch to the LOCK position.




PINPOINT TEST A: THE SHIFT INTERLOCK SYSTEM DOES NOT RELEASE/LOCK CORRECTLY







A1 TEST THE BRAKE LIGHTS









  • Apply the brake pedal and view the brake lights.

  • Do the brake lights illuminate?




Yes

GO to A2 .



No

REFER to Section 417-01 .




A2 TEST SHIFT INTERLOCK ACTUATOR POWER CIRCUIT









  • Disconnect: Floor Shifter Harness Connector C3245.

  • Key in ON position.

  • Measure the voltage between floor shifter harness connector C3245-1, vehicle harness side and ground, while applying the brake pedal.

    Is the voltage greater than 10 volts?
A3 TEST SHIFT INTERLOCK ACTUATOR GROUND CIRCUIT



  • Key in OFF position.

  • Measure the resistance between floor shifter harness connector C3245-4, vehicle harness side and ground.

    Is the resistance less than 5 ohms?

Yes

INSTALL a new selector lever. Refer to Selector Lever in this section.

No

REPAIR the circuit. TEST the system for normal operation.

May 25, 2015 | 2006 Ford Fusion

1 Answer

HAVE A 1989 FORD F-150 WITH AUTO TRANS THAT YOU CAN'T SHIFT OUT OF THE "PARK" POSITION AT THE STEERING COLUMN. THE TRANY CAN BE SHIFTED AT THE TRANS WHEN LINKAGE IS DICONNECTED.I THINK THE...


What trans? AOD? This is 1992 F Series, all I have.

Shift Controls, Automatic Transmission The transmission shift control linkage or cable transfers the transmission operating mode from the selector lever to the transmission. The indicated transmission position on the steering column is transferred to a shift lever on the bottom of the steering column. On vehicles equipped with cable-operated shift systems, the indicated position of the transmission selector lever is transferred to the transmission through the shift cane, then to the cable, and down to the transmission manual shift lever at the transmission. On vehicles equipped with shift rod assemblies, the rod transfers the indicated transmission selector level position through a bell crank assembly to a control rod. The control rod transfers the indicated position to the transmission assembly.
----------------------------------------------
Automatic Transmission Manual Linkage Adjustments
  1. With the engine stopped and the parking brake applied, place the transmission selector lever at the steering column in the D (DRIVE position) for C6 applications and in the (D) (OVERDRIVE position) for AOD and E4OD applications, and hold against the D or (D) stop by applying a three-pound force to the selector lever knob.
  1. Loosen the shift rod adjusting nut at point A. Refer to the following illustrations.
  1. Shift the manual lever at the transmission into the (D) (overdrive) position for E4OD, by moving the lever all the way rearward, then forward two detents.
  1. With the selector lever and transmission manual lever in the(D) position, tighten the nut at point A to 17-24 Nm (12-18 ft-lb) torque. Use care to prevent motion between the stud and rod.
  1. Remove the three-pound force from the steering column selector lever knob.
  1. Operate the shift lever in all positions to make certain that the manual lever at the transmission is in full detent in all gear ranges. Re-adjust the linkage if required.
  1. On F-Super Duty Chassis Cab and Motorhome and Commercial Chassis recheck for correct operation of the automatic transmission selector indicator (PRN(D)21). Refer to Section 11-04A, Steering Column, Shift Rod Within Tube. ani_caut.gif CAUTION: Under no circumstances will it be permissible to adjust linkage in any position other than the(D) position for E4OD applications.
---------------------
Automatic Transmission Shift Cable Adjustment
  1. From inside the vehicle, place the column shift select lever in the DRIVE position (C6) of the OVERDRIVE (AOD and E4OD). Hang a three-pound weight on the selector lever.
  1. Raise vehicle on a hoist.
  1. Remove the shift cable from the transmission lever ball stud.
  1. Pull down the lock tab on the shift cable body.
  1. Position the transmission shift lever in the DRIVE position (C6) or the OVERDRIVE position (AOD and E4OD). This is three detents from the front-most lever position with the first position counting as one.
  1. Connect the cable end fitting to the transmission lever ball stud.
  1. Push up on the lock tab to lock the cable in the correctly adjusted position.
  1. Lower vehicle down from hoist and remove the three-pound weight from the column shift select lever.
  1. After making the adjustment, check for park engagement. Check the transmission control lever in all detent positions with the engine running to make sure correct detent/transmission actions. Readjust if necessary.

Jun 21, 2011 | Ford F-150 Cars & Trucks

1 Answer

Dash Display shows all shift at same time When you place in shiftronic position for manual ,cant tell which gear it's in


same thing happened to me....unfortunately its a computer thing that costs about 1500. available only thru VW dealer. Problem is if you let it go it has the potential to mess up the gear shift permanently..or so the dealer told me!

Apr 23, 2011 | 2006 Volkswagen New Beetle

1 Answer

I have a 2000 VW Beetle, automatic transmision. The handle is locked on park position. ABS and Brake lights turns on at the same time. How can I unlock the transmision?


possibly the brake light switch above the brake pedal is faulty. The transmition lever will not move unless your foot is on the brake, if the switch that senses this action is faulty, the transmision lever will not move.

when you say ABS and Brake lights turns on at the same time, do mean the lamps at the rear of the car are on or are you refering to warning lamps on the dash panal?

if you meant dash panal then check your stop lights are working, if all 3 dont work, this definately points to a faulty brake light switch.

if your stop lights are on all the time, then this also could be either a faulty switch, or the switch has been dislodged from its bracket above the brake pedal.

Feb 23, 2010 | 2000 Volkswagen Beetle

1 Answer

2006 VW Beetle...need to replace the driver side low beam light...how?


Open the hood and look down beside the battery youll see a black lever.Pull the lever up it may take some patience but it will release,the headlight assembly will slide out of the front of the vehicle.Once you take the assembly out on the backside youll see a metal clip holding the bulb in place.Just depress the clip and it will release,Simply just reverse the procedure for installation.

Jan 31, 2010 | 2006 Volkswagen New Beetle

1 Answer

Gearshift selector problem


The gear selector switch is either out of adjustment or it is bad. Loosen the two bolts holding the gear selector in place and turn it slightly to see if the display stops flashing. You will have to manually shift the transmission lever at the switch into neutral, and then turn the switch until the display says neutral. Tighten the bolts and then check all gears. It's also possible the shift cable could also be out of adjustment. Does the display change if you simply wiggle the gear selector lever?

Oct 22, 2009 | 1988 Oldsmobile Toronado

1 Answer

Shifter alignment cable is out of place, how do i fix it ? If I put the car in drive it roles backwards. I have to drive with the car on 4.


To Adjust : 1- Unclip parking brake boot. 2- Detach the center console upper section. 3- Disconnect cigar lighter electrical connector. 4- Remove te center console upper section , disconnect the transmission mode and traction control electrical connectors 5- Move the selector lever to position "R" 6- Loosen the selector cable lock nut 7- Detach the selector cable. 8- Raise and support the car. 9- Move the Rotary position switch to the "R" position , so that it matches the lever. 10- Lower the car. 11- Connect the selector cable (Do not tighten selector lever lock nut) 12- Move selector lever to "D" , hold the selector lever applying light pressure and fingure tighten the rear lock nut , then fingure tighten the front lock nut 13- Now move the lever to different gear positions , ( when "D" is selected , make sure it sits as close as possible to the "D" and "4" position in each corner. 14- Tighten selector lever lock nut. 15- Install center console upper section. (connect the transmission mode and traction control electrical connectors) 16- Connect the cigar lighter connector 17- Install the center console upper section. 18- Clip together the parking brake boot.
And you are done , I know it looks hard but it is not , read through my instructions and understand it and all will be easy to do. Good luck , hope it helped :)

Jul 27, 2009 | 2001 Jaguar S-Type

1 Answer

My 2006 VW Passat will not turn over...


the sensor that tells the can bus what position the stick is in is located on the gearbox not on gearstick.you need to know what position that sensor is seeing the only way is with a more advanced diagnostic tool than just a fault reader.i would recomend vw dealer as passat electrical sytems can be a bit of a challenge when they go wrong and a dealer will be best placed to sort it for you.

Jan 26, 2009 | 2006 Volkswagen Passat

1 Answer

Shifter indicator light


is this the shift position indicator like drive, park reverse, neutral?

Transmission Selector Lever Removal
  1. Raise and support the vehicle. For additional information, refer to Section 100-02 .
  1. Remove the heat shield.
  1. Disconnect the selector lever assembly.
    1. Disconnect the selector cable adjusting cap.
    1. Disconnect the selector cable.
    1. Remove the nuts.
  1. Lower the vehicle.
  1. Remove the selector lever assembly.
    1. Remove the cover.
    1. Lift out the selector lever assembly.
    1. Disconnect the selector lever electrical connector.

Oct 20, 2008 | 1999 Mercury Cougar

Not finding what you are looking for?
2006 Volkswagen New Beetle Logo

Related Topics:

32 people viewed this question

Ask a Question

Usually answered in minutes!

Top Volkswagen Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

yadayada
yadayada

Level 3 Expert

75117 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7772 Answers

Are you a Volkswagen Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...