Question about 2002 Toyota Camry

Open Question

Does a toyota camry have hydralic or adjustable valves 1998 camry

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 1861 Answers

SOURCE: 1998 toyota camry interior dome light replacement

Look closely at the cover. You will see a small slot. Insert a small flat blade screwdriver, and pry it off. Very easy..

Posted on Nov 10, 2008

  • 65 Answers

SOURCE: 1998 toyota

There is a pin that you have to push in on the bottom of the lock cylinder housing.It is recessed in a hole.You have to turn the key to acc or on to get it to push in.Once you push it in you can pull the key and lock cylinder out.

Posted on Dec 02, 2008

DickCanFixIt
  • 948 Answers

SOURCE: How to read trouble codes on 1998 Toyota Camry w/o scan tool

You can go to any auto parts store and they will usually read them for you for free. Around the late 90s many of the auto computer systems began requiring scan tools rather than the older method of simply flashing lights on the dash if you jumpered the correct pins.

Posted on Dec 31, 2008

  • 1986 Answers

SOURCE: Headlight adjustment instructions

The adjustment screws/nuts should be located either on the top of the headlamp assembly, behind the headlamp assembly, or near the frame rail by the radiator support.

You will have vertical adjustment screws for each independent beam (separate highs and separate lows, but will be same screw if highs and lows are the same bulb). You may also have additional horizontal adjustment screws as well

Park your car on a level ground 30 feet from a wall and measure the height from the ground to the bulb and mark on a wall (do this for highs beams and low beams if the bulbs are separate, if highs and lows are the same bulb, only do it for the lows)

For Low Beams: If the headlights read VOR, then aim the brightest part or cutoff part just below the mark on the wall. If it says VOL or nothing, aim them 2 inches below the mark on the wall.

For High Beams: Aim the headlight directly at the line you marked on the wall.

Posted on Sep 30, 2009

  • 318 Answers

SOURCE: 1998 toyota camry , 2 codes, p0171. + p1133

P0171 lean code. Clean the maf sensor. A f sensor is inthe exhaust pipe.

Posted on Oct 27, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I fix code P402 on the 1998 V6 3.0L Toyota Camry XLE?


That is "Exhaust Gas Recirculation Flow Excessive Detected". The EGR valve may be gunked up or stuck open, so remove and check that. It may also be that the VSV (vacuum switching valve ) connected to it has failed. In Toyotas these little solenoid valves sometimes fail when hot but test OK when cold.

More info is here

http://www.turboninjas.com/camry/eg2.pdf

Sep 26, 2014 | 1998 Toyota Camry

1 Answer

How to replace a servo motor on a 1998 toyota camry


Before tearing out the dash to get at servos, check for vacuum leaks and bad vacuum check valve.

Jan 31, 2014 | 1998 Toyota Camry

1 Answer

1998 toyota camry won't reverse and hesitating in drive


This could be a fault with the shift valve, hopefully just requiring cleaning. This is accessible with the trans pan removed, best done on a hoist.

Dec 30, 2012 | 1996 Toyota Camry

1 Answer

How do i adjust idle for 1989 toyota camry


Its not exactly adjustable, its controlled by the computer by using the idle air control valve.
If the idle speed is too high, you may have a vac leak, or the idle air control valve may be faulty.

Sep 22, 2012 | 1989 Toyota Camry

1 Answer

Valve lash clearance


95 was hydralic ,no adjustment

Aug 18, 2011 | 1995 Toyota Camry

1 Answer

How to adjust valves on a 98 chevy malibu


the valves are hydralic and require no adjustment. if noisey then a bad lifter/rocker arm/cam shaft may be the problem. also low oil level,or foamy oil from to much oil or a leak in the oil pump pickup system could cause noise

Apr 05, 2010 | 1998 Chevrolet Malibu

2 Answers

What is the best power steering fluid to use in a toyota camry


Lucas oil ...power steering fuild with conditioner. Or Casite honey power steering fluid. Even Prestone would be fine.

Feb 05, 2010 | 1995 Toyota Camry

1 Answer

My 98 Camry has a tapping sound from the engine as it runs. Is this normal? It sounds like the pistons.


well that is not normal go to a nearest mechanic and then advise them to check the valve of your engine maybe it needs some adjustment. And check the oil level of your engine also.

Feb 04, 2010 | 1998 Toyota Camry

2 Answers

Smell smoke


There is most likely an engine oil leak that is leaking on the exhast that runs accross the bottom of most toyota engines. Valve cover is common

Jul 02, 2009 | 1998 Toyota Camry

1 Answer

Engine noise


If its sounds like its under the valve cover then it would be a valve lash adjuster on the rocker.

Feb 03, 2009 | 1998 Toyota Camry

Not finding what you are looking for?
2002 Toyota Camry Logo

Related Topics:

13 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

75077 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7768 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...